Tender For supply of valve cone, ass drg desc: h. p control valve, assly drg no. : 01122305000, part no. : 4, variance no. : 0 , emergency governor, ass drg desc: emergency governor, assly drg no. : 01162705000, part no. : 0, varianc
Tender For custom bid for services - 30 mw & 14 mw tg miscellaneous works at nspcl-bhilai power plant-2- 10.10 tmstu61bd000 steam tur(bearing pedestal)attend defect: 1. take permit to work from concerned person., 2. remove control valve linkages, oil piping and other connections from the pedestal., 3. remove front pedestal top cover., 4. clean front pedestal housing., 5. take measurement as per instruction of eic. (involves checking of pinion shaft/gear, assembly, main oil pump gear wheel, gov. assembly & checking the backlash of gears.), 6. attend the defect/trouble shoot the problem in front pedestal as per instruction of eic., this includes the following work beside defect attending as per instruction of eic., 7. dismantle pinion shaft and record the alignment w.r.t to the gov. assembly., a) dismantle mop (main oil pump) bearings and gear., b) do servicing of mop and replace damaged items., c) dismantle governor assembly (consists of gop-governing oil pump and other, elements)., d) do servicing of gop and replace damaged items., e) assemble mop and governor assembly., f) put governor assembly in position., g) do alignment of the pinion shaft w.r.t to governor assembly., h) put electronic over speed shaft (pinion shaft) in position., i) put mop assembly in position., j) record backlash of gears and if requires, do adjustment., 8. measure the clearances of first three rows of oil gland fins & its servicing, 9. assembly of oil gland segments (new or old) and setting of clearances., 10. after the work, box up front pedestal top cover., 11. link control valve linkages, oil piping etc., 12. do rig test for setting governing characteristics., 10.20 tmstu56oh000 steam tur (bearings) serv- 1. take permit to work from concerned person., 2. remove control valve linkages, oil piping and other connections from the pedestal., 3. remove front pedestal top cover., 4. check bearing interference, toc, soc etc., 5. remove turbine front bearing top & bottom halves., 6. do the dpt and ut of turbine bearing., 7. check thrust bearing pads and do dpt, ut and blue matching., 8. check toc, soc, bearing interference of bearing after servicing., 10.30 tmstu01bd794 steam tur (<=30mw#) repl-gland- 1. removal of first 2 rows of hp front steam gland segments., 2. servicing of (new or old) gland segments and springs., 3. measurement of dimensions and machining of gland segments if required., 10.40 tmtgs01bd701 turbine gov. sys (<=30mw#) maintenance- i) attending passing defect in four nos. steam control valves, ii) servicing of two nos. hydraulic servomotors (including relay gear) of control valves, iii) inspection & servicing of speed governor and setting its governor characteristics (rig test)., iv) inspection & servicing of cies valve (left & right)., 1. ensure ptw from concerned person., 2. breaking of insulation around steam control valves & removal of debris from site., 3. dismantle linkages and decouple all four nos. control valves from spring box assembly, 4. remove spring box assembly from position., 5. dismantle bonnet bolts & remove all four control valves., 6. check blue contact / kerosene test of plug with respective seats., 7. do lapping of all control valves, replace plug/other components, if required., 8. assemble all control valves and tighten bonnet bolts., 9. servicing of cies valves (left & right), 10.servicing of spring box assembly hinges & pins etc., 11.place spring box assembly & couple all control vales with spring box., 12. servicing of two nos. hydraulic servomotors of control valves., 13. servicing of primary relay oil cylinder for checking for excessive draining of oil. replacement of relay gear power, piston if needed., 14. servicing of secondary relay., 15. servicing of linkage., 16. replacement of steam leak-off and impulse line pipes as per eic instruction. dp test of welding joints are to be, carried out., 17. inspection of speed governor, assessment of its component s healthiness, repl
Tender For supply of 19/30, single conductor, extra flexible,260 degree celsius thin walled abrasion resistant reinforced ptfe type teflon insulated 600 v control cable for ww governor amph enol plug,emd part no.8453180/dlw partno:18330332. [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : tender for supply of element thermoregulating lt , element thermoregulating ht , starting air hose , governor control shaft , sealing set , shim adjusting assembly , holder injector overhaul kit , seal , sealing set , ring piston , set of sealing for heads of cylinders blocks , sealing set for decompressor , inlet rocker arm & adjusting screw , exhaust rocker arm & adjusting scre , sealing , pinion set fuel pump , bearing , pre lub oil pump coupling , ht impeller , lt impeller , screw , washer , water pump overhaul set , governor drive overhaul kit , neoprene protection , right swivel articulation , left swivel articulation , ring o ring , screw for charge air cooler , screw , screw for charge air cooler , screw , screw , screw , screw for charge air cooler , screw for charge air cooler , sealing for fuel oil pre filter , ring sealing , ring sealing , ring sealing , ring sealing , ring sealing , ring sealing , ring sealing , sealing , sealing , sealing , ring sealing , spacer for cac , element filtering , cartridge of filter , paper filter , set of sealings for centrifugal filter , liner assembly , seals set hot box , connecting rod equipped , piston with pins and rings , gudgeon pin , cylinder head assembly , cylinder head overhaul kit , inlet valve yoke assembly , exhaust valve yoke assembly , push rod , cover cam roller , valve tappet maintenance kit , valve tappet sub assembly , air coolant overhaul sealing set , sealing se air coolant remounting , turbocharger overhaul kit , sealing set injection pump , injection pump assembly , connection piece , connection piece , pipe injection , o ring , injector seal kit , hose , hose , hose , fuel pump coupling , pin , thermostatic lement , gear + fitting set water pump , sealing setwater pump reassembly , gear + fitting set sea water pump , hose priming , key , washer , nut , pin , thermostatic element , spacer , multiduct , spacer , turning gear assembly , starting gear , screw , screw , screw , screw , screw , washer , washer , dowel pin , plug , plug , swivel connection , connection , pipe union , pipe union , pipe union , pipe union , pipe union , connection , pipe union , tee tube connector , swivel connection , o ring case , sealing , sealing , sealing set for injection pump head , o ring , o ring , o ring , shell to tubesheet gasket , fronthead to tubesheet gasket , shell side nozzle gasket , tube side nozzle gasket , o ring for black header , grid , flexible bush , sealing set cooling circuit , sleeve , hose , cartridge fuel filter , venting screw , lube oil module sealing set , hose , turning gear sensor , multipurpose pipe b side , multipurpose pipe a bank , pipeturbo wiring , cable har cpt turbo w200d45m , speed sensor overspeed , speed regulation sensor , temperature turbine inlet , high temperature switch oil engine inlet , cylinder temperature , fuel temperature engine inlet , oil pressure switch engine inlet idle speed , oil pressure engine inlet , water pressure engine inlet , seal set water/glycol water exchanger , sealing set fuel filter , sealing set prefilter , sealing disc tps52 , governor driving pinion , by pass valve overhaul set , oring , shaft , impeller , shaft , colling water hose , seal , o ring , hose , electrovalve for rigsaver , screw , pipe union , tee connection