Latest digital meter Tenders | Government digital meter Tenders

CTN :45446753

22 Jun, 2026 57.77 Lacs

Bhiwani - Haryana

Tender For supply erection commissioning of electrical and mechanical equipment for dewatering of flood water from field area for village badesra outfall at rd 70600 l of jui feeder - estimate for supply, erection & commissioning of electrical & mechanical equipment for dewatering of flood water from field area for village badesra outfall at rd 70600-l of jui feeder in lift w/s (m) division, bhiwani - supply, erection & commissioning of 5 c/s axial flow water lubricated vertical pumps of 5 cs. discharge at 1440 rpm at static head of approx 8.0 mtr. with y body, including ms bend including flange welding, nut & bolts etc complete in all respect as per site requirement with epoxy coating & as per approved specifications of the department, supply, erection & commissioning of solid shaft motor of capacity 30 hp, 1440 rpm, 3 phase, 380 volt+- 10%, with eficiency class ie2 suitable for fitment with 5 cs. v.t axial/mix flow pump type vertical flange mounted as per approved specifications of the department, supply, erection & commissioning of fully automatic star delta starter suitable for 30 hp motor as per ip 54 with all allied item like mccb, contactor, rating 120 amp 90 amp, 50 amp, all type of protection relays (over voltage, under voltage, over corrent, singhle phasing preventor, delay siwtch ) correction capacitor, digital meter, bus bar, thimble etc suitable and all live parts should be covered as per site demand and compartment coated with epoxy coating as per approved technical specification of department. (including cable suitable for panel to motor).

CTN :45446757

22 Jun, 2026 73.10 Lacs

Bhiwani - Haryana

Tender For estimate for supply, erection & commissioning of various electromechanical equipment like 5 no. 5 cs. vt pump, electric motors, starter panel and other allied material for flood protection works from the field area of village dang khurd & outfall at rd 65000-r of nigana feeder in lift w/s (m) division, bhiwani for the year 2026-27. - supply, erection & commissioning of 5 c/s axial/mix flow water lubricated vertical flood pumps of 5 cs. discharge at 1440 rpm at static head of approx 6.0 mtr. having adjustable height, including ms bend including flange welding, ss/ht nut & bolts etc complete in all respect as per site requirement with epoxy coating & as per approved specifications of the department, supply, erection & commissioning of solid shaft motor of capacity 30 hp, 1440 rpm, 3 phase, 380 volt+- 10%, with eficiency class ie2 (with 35 mtr compatible 3 phase submersible cu cable from motor to panel/starter) suitable for fitment with 5 cs. v.t axial/mix flow pump type vertical flange mounted as per approved specifications of the department., supply, erection & commissioning of fully automatic star delta starter of cap. 150 amp including all accessories as one incomer of mccb (150amp) with 1 no mcb for lighting load, contactor rating 120 amp, 90 amp, 70 amp with control transformer for control supply, outgoing indicator, having mpr & all types of protections i.e.uv/ov/ over current, phase imbalance/phase reversal protection, locked rotor, dry run etc, digital meters, push buttons, bus bars, capacitor bank, seperate relay for single phase protection etc. complete in all respect suitable for open fields operation of 1 no. motor of capacity of 30 hp with a stand of ms channel with canopy having suitable operating height above the kachha open fields as per approved specifications of the department. (suitable for voltage range 380 +- 10%,) panel should be outdoor type., supply, erection & commissioning of m.s delivery pipe 10" dia. made of ms plate both end flanged (equal to or less than 6 mtr length of pipe) as per approved specification & make. (including ss/ht nut & bolt, rubber packing & other fitment accessory required), supply, erection and commissioning of ms girder parallel flange section ismb 150 with primer and bituminous based paint inside & outside of length 4mtr (approx wt 60 kg per pc) as per approved make & conforming to is808:2021.

corporations/Associations/Others

CTN :45407789

02 Jul, 2026 NA

Kolkata - West Bengal

Tender For supply of various electrical lt switch gears control equipment and cables in the ltdb of power load b b - supply of 630 amp 3 pole mccb 415 volt, , supply of spreader link for 630-amp 3 po , supply of extended rod with handle 630-a , supply of ring ct make- kappa, ratio- 60 , supply of 400 amp 3 pole mccb 415 volt, , supply of spreader link for 400-amp 3 po , supply of extended rod with handle 400-a , supply of ring ct make- kappa, ratio- 40 , supply of 200 amp 3 pole mccb 415 volt, , supply of spreader link for 200-amp 3 po , supply of extended rod with handle 200-a , supply of ring ct make- kappa, ratio- 20 , supply of 100 amp 3 pole mccb 415 volt, , supply of spreader terminal for 100-amp , supply of extended rod with handle 100-a , supply of ring ct make- kappa, ratio- 10 , replacement and retrofitting of 630 amp 3 , replacement and retrofitting of 400 amp 3 , replacement and retrofitting of 200 amp 3 , replacement and retrofitting of 100 amp 3 , supply of 95 sq mm single core copper fl , laying of 95 sq mm single core copper ca , supply, replacement and re-fixing of 95 , supply of indicating led lamp red- 60 n , replacement and re-fixing of indicating , supply of multifunction meter make- secu , installation, calibration, testing and ret , supply of auxiliary contactor for mccb m , ring ct installation and retrofitting , control cable connection and circuit mod , supply of 2.5 sq mm flexible wire , supply of 400 amp 3 pole power contactor , supply of 160 amp 3 pole power contactor , supply of 160 amp 3 pole mccb for capaci , supply of spreader terminal for 160-amp , supply of extended rod with handle 160-a , replacement and retro-fitting of 400 am , replacement and retro-fitting charges fo , replacement and retro-fitting of 160 amp , supply of 12 window apfc relay, make- ep , replacement and retro-fitting charges fo , supply of 3-phase digital voltmeter make , supply of 3-phase digital ammeter make- , replacement and retro-fitting of 3-phase , rectification and restoration of mechanic , supply of 300 sq mm, 3.5 core, 1.1 kv gr , supply, fitting and fixing of gland for 30 , laying of 3.5 core, 1.1 kv grade armoure , supply and replacement of socket for 300 s , manual disconnecting of power supply, di , supply, installation, testing and commis

CTN :45419880

13 Jun, 2026 NA

Patiala - Punjab

Tender For supply of hero hf deluxe motorcycle into hybrid lectric stelth mobility vehicle d d - hub motor kit , lithium ion battery , motor controller , charger unit , dc-dc converter , battery box fabrication , heavy wiring kit and connectors , main fuse mcb , ignition switch , rear disk brake calipers , digital meter , tyre with nozzle fitment , bike wrapping vinyl

CTN :45417602

10 Jun, 2026 NA

Tiruvallur - Tamil Nadu

Tender For supply of lab items for eee and mechanical - eee and mechanical lab items, single phase transformer rating: 1 kva, 50 hz input: 230 v ac output: 115 v ac type: air-cooled, single-phase step-down transformer properly insulated input and output terminals brought out for safe operation, three phase transformer type: three phase transformer rating: 3 kva input voltage: 415 v ac, 3-phase output voltage: 230 v ac, 3-phase frequency: 50 hz winding material: copper wound insulation class: class b or higher duty: continuous duty suitable for laboratory use bench/floormounted suitable for laboratory operation. all winding terminals shall be brought out to insulated terminals and enclosed within a protective outer cover for safe laboratory operation , on / off control of lamp using solid state relay kit type : solid state relay (ssr) trainer kit control/input voltage : 12 v / 24 v dc or up to 30 v dc output load voltage : 230 v ac, single phase load control : on/off control of ac lamp load solid state relay based switching circuit opto-isolated input control built-in ac lamp load manual on/off switching arrangement led indication for input and output status , mcb elcb trainer kit 1 phase/3 phase, 2/3/4 pole, 3a-16a single pole mcb 2-5amps two pole elcb 30ma lamp load single phase 5amps panel enclosure and terminal outlets , single phase induction motor kit for load test by speed control of vfd (variable frequency drive) 2 hp single phase 230v complete load test experimental setup(with brake drum/pulley) induction motor -1 no work bench setup with digital meter -1 no motor stand with ant vibration bush 1 set loading arrangement with spring balance non-vibrating brake arrangement with stand and electrical work bench , 3 phase induction motor kit three phase squirrel cage induction motor with rope brake arrangement non-vibrating brake arrangement with stand and electrical work bench three phase squirrel cage induction motor 5 hp, 440 v, 1440 rpm, foot mounted type, frame size 132 mm, core length 110 mm, mechanical rope loading set up with 1" screw rods 2 nos, 6" adjustable wheels 6" 2 nos, back support frame, 9" aluminium drum, 0 50 kg spring balances 2 nos , dc shunt motor kit for load test dc shunt motor rope brake arrangement non-vibrating brake arrangement with stand and electrical work bench d.c. shunt motor 5hp, 220v, 1500 rpm, foot mounted type, frame size 132 mm, core length 110 mm, field current 0.5a, armature current 11a, 4 pole with inter poles, mechanical rope loading set up with 1" screw rods 2 nos, 6" adjusting wheels 6" 2 nos, back support frame 9" aluminum drum, 0 50 kg spring balances 2 nos. , bldc motor kit with electrical work bench *36v 400w bldc pro motor 1 no inbuilt volt and ammeter and rpm meter inbuilt power supply input 230v ac

Central Government/Public Sector

CTN :45246782

05 Jun, 2026 NA

Bangalore - Karnataka

Tender For corrigendum : supply of digital meter 8.5 and 6.5

Central Government/Public Sector

CTN :45372347

05 Jun, 2026 NA

Multi City - Multi State

Tender For automatic premix coffee dispensing machine 1. item dispensed: tea, coffee, milk, water, soup 2. body material - galvanized iron sheet 3. dispensing valve material - plastic 4. tray material - plastic 5.material of raw mixture chamber - polypropylene 6. number of raw mixture chambers - 4 nos. 7. with volume adjustment , continuous dispensing function . auto-clean & auto flushing function 9. water supply in machines - submersible pump 10. programmable digital controls pre-programmed beverages - 10 nos. 11. built with flow meter ,digital meter to count no. of drinks dispensed, programming on front lcd panel, auto water flushing & sleep mode 12. inbuilt hot water storage capacity - 2.0 ltrs 13. raw mixture chamber capacity - 4 ltrs. 14. dispensing rate - 140 cup per hrs 15. power - 2.0-2.5 (kw) 16. warranty - 1 year. 17. accepted make- godrej, netscafe, bru, tata,cafe desire 18. installation by the supplier at the site. [ warranty period: 12 months after the date of delivery ] ]

CTN :45175490

01 Jun, 2026 NA

Jhabua - Madhya Pradesh

Tender For corrigendum : tender for supply of motor samagri - technical specification 2hp item set v4 (single phase) 20 hp 16 stage item set v6 (three phase) 05 hp item (three phase) - texmo 50 hp 08 stage vertical open well pump set v8 01 hp open well pump (single phase) 02 hp open well panel (single phase) 20 hp automatic star delta item (three phase) 15 hp panel item (three phase) digital meter cut out fuse 200 amp cut out fuse 63 amp 06 mm cc 03 core (three phase) 08 mm ac 02 core (single phase) 12 mma w (90 metre) bundle breaker machine 21 kg ld-joint class-15-isi 90 mm ld-joint class-15-isi 110 mm cld-joint class-15-isi 150 mm ld-joint class-15-isi 200 mm hdpe c.1.d. joint 90 mm. hdpe c.1.d. joint 110mm hdpe c.i.d. joint 125mm hdpe c.i.d. joint 140mm hdpe c.i.d. joint 160mm hdpe c.i.d. joint 180mm hdpe c.i.d. joint 200 mm clamp set with nut bolt - 4 inch clamp set with nut bolt-6 inch clamp set with nut bolt - 8 inch pvc coupler isi in 6kg-90 mm pvc coupler isi in 6kg-110 mm pvc coupler isi in 6kg-140mm pvc coupler isi in 6kg-160mm pvc coupler isi in 6kg-180mm pvc coupler isi in 6kg-200mm aplon (teflon tape)

corporations/Associations/Others

CTN :45332552

16 Jun, 2026 NA

Jammu - Jammu And Kashmir

Tender For supply of wiring for light point fan point exhaust fan point call bell point with 1.5 sq.mm , earth wire , supplying and drawing following sizes of pvc conduit as required 1.5mm , modular plate , supplying and fixing two module stepped type electronic fan regulator on the existing modular plate , supplying and fixing modular blanking plate on the existing modular plate , supplying and fixing following size , 3 module 100mmx75mm , 4 module 125mmx75mm , 6 module 200mmx75mm , 8 module 125mmx125mm , 12 module 200mmx150mm , supplying and fixing suitable size gi box , 15x16 amps , a exhaust fan of all sizes. , modular plate and cover in front on surface or in recess , providing and fixing 25 a , mcb distribution board , single pole 6 to 32 amp , single pole and neutral 6 to 32 amp , single pole and neutral 63 amp , triple pole and neutral 32 amp. , 63 a tpn mcb 10 ka c curve , mcb db complete etc as required , 32 a 415 v c curve tp mcb , 600 mm x 600 mm x 6 mm thick watering pipe of 2.7 meter long etc. , providing and fixing 25 mm x 5 mm gi , providing and fixing 6 swg dia gi , led batten light 40 watt , ceiling fan 3 star rated with voltage range 90 v to 300 v 1200 mm , 300mmx12 inch sweep exhust fan , 50 w flood light 50 watt , sitc of building distribution panel indoor , 160 a 36ka fpmccb , aluminium bus bar 200 amp set of 4 strips 18 inch , digital metering devices , supplying and laying of following size dwc hdpe pipe isi marked along with all accessories , supplying and laying of one number pvc insulated and pvc sheathed , supply and making end termination with brass compression gland and aluminium lugs , 2.5 kva sine wave inverter input 1 phase 3 wire and output 1 phase 3 wire with 2 nos of 12 v 200 ah battery , hot dipped galvanised iron cable tray 100 mm width x 50 mm depth x 1.6 mm thickness

Central Government/Public Sector

CTN :45251822

03 Jun, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For providing of calibration services - mechanical, electrical, thermal, fluid flow, glassware; dimension, mass and volume, pressure and vacuum, specific heat & humidity, temperature, gas analysis, pressure, pressure guage and digital meter; nabl labs; buyer premises..

Digital Meter Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Central Government/Public Sector

Central Government/Public Sector

corporations/Associations/Others

Central Government/Public Sector