Get complete information related to latest Discrepancy Switch Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Discrepancy Switch Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Discrepancy Switch Tenders.
Tender For corrigendum : repair and replacement of all internal components of laboratory equipment that sustained damage due to the severe flooding caused by the beas river - repair, removal of silt and cleaning of incubator 36"x24"x24" and replacement of (digital temp. controller. 6 element, d fan motor, sensor. insulation with paint & wiring etc.) including carriage in all leads and lifts., repair, removal of silt and cleaning of existing incubator size of 24"x18"x18" and replacement of (digital temp. controller, 6 elemen fan motor, sensor, insulation with paint, wiring etc.) including carriage in all leads and lifts., repair, removal of silt and cleaning of existing hot air oven size of 18"x18"x18" and replacement of (digital temp. controller. 6 element. fan motor, sensor, insulation with paint, wiring etc.) including carriage in all leads and lifts., repair, removal of silt and cleaning of existing laminar air flow,size of 4x2x2 and replacement of (hepa filter, pre filter. uv light 1 nos, fluorescent light, centrifugal blower motor with paint i nos wiring, etc.) including carriage in all leads and lifts., repair, removal of silt and cleaning of existing biosafety cabinet, size of 5x2x2 and replacement of (hepa filter, pre filter, uv light 1 nos, fluorescent light, centrifugal blower motor with paint 1 nos wiring, etc.), repair, removal of silt and cleaning of existing autoclave vertical and replacement of (element, psi control switch, water level switch, pressure gauge, safety valve, wiring, etc) including carriage in all leads and lifts., repair, removal of silt and cleaning of existing lab refrigerator and replacement of(complete cooling unit with temperature controller) wiring etc. including carriage in all leads and lifts., repair, removal of silt and cleaning of existing water bath and replacement of(heater, pilot lamp, thermostat, wiring etc) including carriage in all leads and lifts., repair, removal of silt and cleaning of colony counter and replacement of (mother board. display, electrode wiring etc). including carriage in all leads and lifts., repair, removal of silt and cleaning of water distillation glass part including carriage in all leads and lifts.
Tender For procurement of koel da rkit 26 and ard 25 - cgsd (mbi), air starter, da sea water pump / assembly of raw water pump, automatic voltage regulator,, dv electronic governor with over speed protection, set of joints, starting air pressure sensor, hp pipe assembly, speed control unit, temp sensor with inbuild transmitter (type-mbt5560,range 0-150d, outpu, limit switch, turbo oil drain pipe, double gear assembly, 0-2.5 bar danfoss make pressure transmitter for marine, pf33 individual pump, fuel pipe (from tank to feed pump tee) (marine-abs approved), set of o ring, exhaust temprature sensor with 2pin connector, fuel leakage switch, pump to leak off (marine abs approved), leakoff pipe (uniflex), piston assembly, fuel pipe (feed pump tee to filter in marine - abs approved), turning gear engaged limit switch, fuel pipe (from fuel filter to fip) (marine abs approved), centrifugal oil cleaner (band design), assly. rocker lever, oil filter element, k-coolant (26 lit can), small end bush (finished), belt v section (bx 58-pitchl ength 1520), hose reducer elbo, set of copper washers, fuel pipe (tee to pump inlet gear end) (marine abs approved), fuel pipe tee to feed pump gear end (marine abs approved), leak off pipe (from hp pipe to collector)marine _x0013_ abs approved, fuel pipe (tee to feed pump) (marine abs approved), belt for sea water pump drive, water level switch, thermostat element, hose for turbo compressor out, breather pipe, breather hose for marine, elbow connection, cly.head steel gasket 1.2 mm, bend 90 for feed pump out, top piston ring, exhaust valve, leakoff pipe for hp jacketed pipe (lh), drain cock, hose (dia 54) (bet.2 pipes), oil control ring, fuel pipe (tee to pump in), nozzle body (for oil spray nozzle), second ring piston, inlet valve, bolt (bearing cap), make up pipe, fuse terminal block 6a with 2a fuse link, exhaust valve seat insert, connecting rod bolt, rc joint, m.b.cross bolt (short), clamp(for fuel pipe), joint for governor mounting plate, special nut for exhaust manifold, valve seal, counter shunk head screw (for dv injector leakoff), valve guides, exhaust manifold stud, grommet: 22 dia ferrule, rubber bush (bottom), joint (bet.exh.manifold and expa. bellow), s.s.nut, sealing cap (for dia 25), valve collet, sealing cap (40 din 443)8, o ring: drain plug, grommet: 12 dia ferrule, stud-m10x1.5x25-8.8, set screw m8x1.25x25...8.8, washer copper, cup for valve springs, gasket (lub oil header), washer copper (18x22), plain machined washer - m6, service kit for heat exchanger, fuel feed pump, service kit for centrifugal filter, k cool super plus 50-50 premix 26 liter can, k-cool super plus, bearing, bearing, k sealent (80 ml), flat seal for oil seal housing, oil seal for drive end, conical copper washer, spring, cup for pr tube, flexible bellow, sea water outlet pipe from cac, joint for t connection, joint for sea water pump, joint for sea water piping, pipe for he raw water out, roller tappet assly, rubber sleeve, set bolt-m14x2x60-8.8, dowel pin, k cool plus 26 ltrs can, clamp (2 pipe), crank pulley, inlet valve seat semi-finish, exhaust valve seat semi- finish, cup washer (for nozzle clamp), valve guide, oil seal pulley end, timing pointer (for pulley), air shut off valve, set of main bearings, set of thrust washer, set of gasket for heat exchanger ts6m, oil pipe ( crankcase to pump), hose for air starter, sub assembly of bearing housing, joint cooler cover(rh)from fwe, k-coolant (26 ltrs can), copper washer (18x22), k-sealant, wire braided pipe from jacketed leakoff to fuel collector, temperature guage (0-120 deg), rubber bush (top), pressure guage (0-4 bar), pipe(sea water pump outlet to check valve), o-ring for drain plug, npt plug with zinc bar with he, k sealant 80 ml, drain cock, stud, set screw -m8x1.25x25-8.8, hose clip, copper washer, anti vibration mount - cori, anabond 666t max 25g, hose t bolt, hose clamp, rotary drain pump, k sealant (80 ml), automatic voltage regulator, worm drive hose clip (70mm), se
Tender For procurement of spares for il-76 aircraft - relay box, seat back rh, cyl attachment bracket, deflector outer wing (lh), ramp cylinder, chanel unit, cylindr side door, dme (sd-67m), encoder, shock mount dme i, eletrical driven centrifugal pump, valve, mobile rig for hyd system optimisation, shutter, block, flexible wave guide kp-2, wave guide kp2, transreceiver r-832m, v/uhf trans receiver r-832m, invertor change over unit, power unit (6em-8), block, measure unit, switch-pressure(v), flow detcector, sensor flex detector, ppi,hr scope and rackkp2-4a-7, device, crane cock, ammeter, oxygen regulator
Tender For corrigendum : procurement of lab instruments for chemical lab of ogcd, dtps, htps, kasimpur - sension5 portable conductivity meter specification range:#conductivity s/cm 0 to 19.99; 200 to 1999#conductivity ms/cm 2 to 19.99; 20 to 199.9#tds: 0 to 50,000 mg/l as nacl salinity: 0 to 42 g/l (ppt)#temperature: -10.0 to 105.0 c#resolution:#conductivity 0.01; 1.0#conductivity ms/cm 0.01; 0.1#tds: 0 .00-199.9 mg/l 0.1mg/l 2 00-1999 mg/l 1 mg/l 2 .00 -19.99 g/l 0.01 g/l 2 0-50 g/l 0.1g/l #salinity: 0.1 g/l (ppt)#temperature: 0.1 c#accuracy:#conductivity: 0.5% in the first 3 ranges, 1% at highest range #td of full scale #salinity: 0.1 ppt (-2 to 35 c) #temperature: 0.1 c# , make-hach, ph meter probe (ph meter sension ph3) cat no-lzw5010t.92.0002 make hachdetails in photograph enclosed in tender document, manual sieves shaker (with sieves set - mesh size-50,+100,+200) any standard make details in photograph enclosed in tender document, centrifugal machine for oil testing, any standard maketube capacity:no.12-24:size 15 mlshould have a digital timerbody should be made of strong fabricated & corrosion resistant steel.control panel- for start/stop switch, dynamic brakes, step less speed regulator with zero start switch & speed indicator with timer and protective fuses.door interlock.maintenance free brushless drive motor with exact speed preselection and display. speed range 100 to3000 rpm and above, accuracy 1 rpm. details in photograph enclosed in tender document, orset appratus (complete set), any standard make details in photograph enclosed in tender document, ph 2700 ph meter specification #ph range -2.000 to 20.000 ph #resolution 0.1 / 0.01 / 0.001 ph #accuracy 0.002 ph + 1 lsd #cal. points up to 6 preset or 5 custom #buffer sets usa, nist, din, user 1, user 2, custom #or range 2000.0 mv #rel. mv range 2000.0 mv on 0.1 mv# accuracy 0.2 mv #temperature,range (meter) 0.0 to 100.0 c / 32.0 to 212.0 f #resolution 0.1 c / 0.1 f #accuracy 0.3 c / 0.5 f #compensation atc / mtc #power requirements 9 v dc adapter, 1.3 a (100/240 vac, smps)# make- eutech
Tender For corrigendum : tender for supply of electrical boards and cabinets - power supply 28v 2a 50w , power supply 2x12v 2a 50w , identification board , distribution board , centrifugal electric pump starting converter unit , complete bridge of power 250a , air conditioner control unit , air conditioner control unit , air conditioner control unit , air conditioner control unit , air conditioner control unit , forward fresh water cooling circuit electric pump starting u , volumetric electric pump starting converter unit , forward sea water cooling circuit electric pump starting uni , sea water electro-pump staring unit , fresh water electro-pump staring unit , hydraulic fluid starting units , air compressor starting unit , 2-position reversing switch 3a with locking-yellow end , complete bridge of power 60a , complete bridge of power 130a , complete bridge of power 130a , quick-blow fuse cartridge 1a type ha22 5x20mm , control board , distribution board , distribution board , identification board , identification board , interface board , static contactor 25a 1700vdc peak - cmd 4.5-32vdc