Get complete information related to latest Draw Muscle Machine Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Draw Muscle Machine Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Draw Muscle Machine Tenders.
Tender For re babbiting-dismantling of bearings and pads from housing,rebabbiting of 10 nos tgb thrust pad along with all accessories,rebabbiting of turbine guide bearing, mid bearing & end bearing along with floating seals and all accessories,material composite test, ut test and dp test should be done for re-babbitted material,assembly of re-babbited bearings with blue match,submitting the video graphs of re-babbiting and reports of re-babbiting.re-alignment-the reason for shifting of generator shaft by 2 to 3 mm shall be analyzed and rectification works needs to be carried out,complete dismantling, assembling, painting and re-alignment of machine shaft,inspection of turbine shaft journal surface and repairs if required,inspection/replacement of worn out bushes and seals of guide vane, if necessary,inspection and repair of labyrinth ring, face plates, guide vanes and runner,guide vanes bed setting,tgb water cooler descaling work to improve the efficiency of cooler,complete assembly of machine,checking the magnetic axis of the generator and to ensure its alignment, checking of the unit leveling at all places and complete alignment of machine shaft,testing & commissioning of complete machine,painting of entire machine,checking of vibration & site balancing of machine,submission of vibration, balancing & alignment reports.flow switch-supply and installation of flow switch (flow rate110 lpm) along with 01 no 01 nc contact for inlet and outlet lubrication oil pipelines,supply and installation of pressure switch (30bar) for inlet and outlet lubrication oil pipelines,supply and installation of level switch for in tgb oil sump.replacement of new miv trunion shaft-dismantling of miv counter weight, miv servomotor assembly, and other related parts,lifting of miv from the bed,transportation of miv to the firms place, if required,replacing old nitrile rubber trunnion seals with existing profile by new one on both sides,replacements of miv trunnion shaft. providing of necessary drawings,material composite test, ut test and dp test should be done for new trunnion shaft & trunnion seals, bushes etc,all related fasteners and dowel pin to be replacing by new one,drive and non drive end trunnion bush, cupseals, stop end plate, washer ring etc need to be replacing by new one,repair of miv discand main body to be attended, if required,supply and replacement of miv disc rubber seal,pressure testing and commissioning should be carried out as per standard in presence of kpcl engineers,all tools & tackles required for the above mentioned works shall be arranged by contactor only.
Tender For corrigendum : supply of ferritic steel sheet 5x1250 x 3000 mm., as per drawing: rdso spec no.c-k201, gr ade x2crni12 (409m) table 1&2. heat treatment condition 2d as per table-5., packing instruc tion: stainless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic st eel) coils. the coil shall be protected in reasonably good condition to withstand nor mal handling hazard during transit with the following provision as the barest minimu m: i) coil should be wrapped with a layer of water proof paper through out whole leng th. ii) coil should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil should be wrapped with gi sheet. iv) side of the coil should be covered with card b oard sheet. v) after this whole coil should be wrapped with biodegradeable plastic sh eet of suitable thickness. vi) the inner edge of the coil should be protected by gi ring f ollowed by another iron ring. vii) outer edge of the coil should be wrapped with gi rin g. viii) coil should be securely strapped with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil shoul d be mounted on wooden blocks for easy lifting/stacking. x) the sheets in coil form fo r thickness 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 100 0-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2 mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 tonnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheet s/plates shall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate s hall be seprated with a layer of water proof paper, after this the whole bundle shoul d be wrapped with double layer of water proof paper and a biodegradeable plastic she et of suitable thickness. a metal protection in edges should also be provided. ii) all bu ndles shall have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every additional meter. the bundles shall also be provided with skid (wooden packing under neath) to facilitate handling. mechanical damange & corrosion during transit if any shall be at the cost of supplier. [ warranty period: 30 months after the date of delivery ]
Tender For supply of ferritic steel coil 1x1250mm., as per drawing: rdso spec. no. c-k201, grade x2c rni12 (409m) table 1&2, heat treatment condition 2b as per table-5., packing instruction: sta inless steel sheets, coils and plates:- (a) stainless steel (austenitic & ferritic steel) coi ls. the coil shall be protected in reasonably good condition to withstand normal han dling hazard during transit with the following provision as the barest minimum: i) coil should be wrapped with a layer of water proof paper through out whole length. ii) coi l should be wrapped with a layer of biodegradeable sheet. iii) outer & inner of coil sho uld be wrapped with gi sheet. iv) side of the coil should be covered with card board sh eet. v) after this whole coil should be wrapped with biodegradeable plastic sheet of s uitable thickness. vi) the inner edge of the coil should be protected by gi ring followe d by another iron ring. vii) outer edge of the coil should be wrapped with gi ring. viii) c oil should be securely strapped with minium 5 steel bands through the eyes of the coil and minium 3 steel bands on the circumference of the eye. ix) whole coil should be mou nted on wooden blocks for easy lifting/stacking. x) the sheets in coil form for thickne ss 2mm and above shall have: inner dia of coil 450-800mm outer dia of coil 1000-1300mm weight of coil 2.4 - 10 tonnes xi) the sheets in coil form for thickness below 2mm shall have: inner dia of coil 450-650mm outer dia of coil 1000-1300mm weight of coil 5.0 - 10 to nnes. (b) stainless steel (austenitic & ferritic steel plates/sheets) i) the sheets/plates s hall be supplied in bundles of optimum weight: 2mt+/-10% & each sheet/plate shall be se prated with a layer of water proof paper, after this the whole bundle should be wrapp ed with double layer of water proof paper and a biodegradeable plastic sheet of suita ble thickness. a metal protection in edges should also be provided. ii) all bundles shal l have a minimum of 2 hoops upto 1.2 meter in length and one extra hoop for every addi tional meter. the bundles shall also be provided with skid (wooden packing under neat h) to facilitate handling. mechanical damange & corrosion during transit if any shall b e at the cost of supplier. [ warranty period: 30 months after the date of delivery ]
Tender For supply of gym equipment - gym dumbbells 12.5 kg , gym dumbbells 15 kg , weight lifting rod 4 ft , weight lifting curl rod 3 ft , weight lifting rod plate 2.5 kg , weight lifting rod plate 5 kg , weight lifting rod plate 10 kg
Tender For suppy of helth material - apron jacket 120 layer super quality jacket must have tatoo of nagarpalika nigam mono, broom hand basket 600 gram 4 feet length, broom stick of basket attached, weight of basket 800 gram 4 feet stick attached, spade (tata company) weight approx 1.040 kg 98 plate length/width, pickaxe, weight approx 3.070 kg, gul shovel iron, weight 2.200 kg (77 inch plate) iron 7 feet length in 1.5 inches, crowbar, approx 6.500 kg (5 feet 5 inch length), small iron basket approximately 1.600 kg in galvanized sheet, big iron basket approximately 2.400 kg in galvanized sheet, thikra scraper (for lifting garbage) approx 175 gms iron seat, gumbut super quality in different sizes 6,7,8,9,10, iron wire brush super quality, claw toothed iron 7 feet length as per office sample, spade handle (wooden) 4 feet length super quality, pickaxe handle (wooden) super quality, carrybag bag 50 kg grain packing capacity like sack size 24"36"(23 feet) length+width umc print on each bag sample available in office, plastic tagari super quality 18" inch diameter, 6" depth, grass cutting sword as per office sample