Latest driven shaft Tenders | Government driven shaft Tenders

corporations/Associations/Others

CTN :40974452

15 Jul, 2025 NA

Koderma - Jharkhand

Tender For supply of brake shoe with lining for eht brake of main hoist , brake shoe with lining for eht brake of aux hoist , brake shoe with lining for eht brake of cross travel , brake shoe with lining of eht brake of long travel , brake spring for eht brake of main hoist , brake spring for eht brake of aux hoist , brake spring for eht brake of cross travel , brake spring for eht brake of long travel , brake thruster for eht brake of main hoist , brake thruster for eht brake of aux hoist , brake thruster for eht brake of cross travel , brake thruster for eht brake of long travel , brake drum of main hoist , brake drum of aux hoist , brake drum of cross travel , brake drum of long travel , pulley assembly for mh main pulley with bearing , pulley assembly for ah main pulley with bearing , pulley assembly for mh equilizer pulley with bearing , pulley assembly for ah equilizer pulley with bearing , main hoist input coupling_motor drive shaft , cross travel input coupling_motor drive shaft , cross travel coupling_wheel side , cross travel coupling_floating shaft side , cross travel output coupling_gear box shaft side , long travel input coupling_motor drive shaft side , long travel coupling_wheel side , long travel output coupling_gearbox shaft side , floating shaft for cross travel , floating shaft for cross travel line shaft , floating shaft for cross travel pillow shaft , input pinion shaft with bearing for main hoist , input pinion shaft with bearing for aux hoist , input pinion shaft with bearing for cross travel , input pinion shaft with bearing for long travel , aux hoist input coupling_motor drive shaft ) /bid number : gem/2025/b/6401352 * /dated: 05-07-2025 & & / bid document 1 / 34

Central Government/Public Sector

CTN :40610423

07 Jul, 2025 NA

Durg - Chhattisgarh

Tender For corrigendum : procurement of loco spares - a floating bushing extension shaft , b floating bushing extension shaft , c floating bushing extension shaft , d floating bushing for lifter , e floating bushing for lifter

CTN :40840744

09 Jul, 2025 NA

Kathua - Jammu And Kashmir

Tender For supply/fitting of bronze bushes in two halves to the plummer block of floating shaft of 16/20 ton capacity 07 nos. radial gates u/s 1 (shaft dia 105 mm contains 02 nos bronze bushes on floating shaft), s/w 5 (shaft dia 62 mm contains 04 nos bronze bushes and 02 nos bearings on floating shaft), s/w 2, 11, 12, 13 & 14 (each tsp gate having shaft dia 70 mm contains 06 nos bronze bushes on floating shaft) installed at ujh barrage. the job includes dismantling of floating shaft from both side of the motor coupled elecon gear box of central drive unit along with plummer blocks of bushes type and nsk-14 bearing type. supply/fitting/fabrication, turning, machining the bronze bushes in two halves as per sample size, drilling holes in bushes making slots for lubrication greasing. supply/fitting of bearing of nsk-14 type plummer blocks by dismantling of old/ damaged bearings and fitted the same as per sample size. job also includes strengthening of floating shafts along with plummer blocks by way of welding, turning and polishing to make it the required size. assembling of all parts with the unit after strengthening of the intermediate supports by way of welding to weakened portion/spots including replacement of old cotter pins, foundation bolts along with nuts. supply/fitting of grease nipples on each plummer block to facilitate the lubrication process. lubrication/greasing to both plummer blocks i.e. bush type and bearing type of above mentioned undersluice and spillway radial gates and testing on full load at site. complete job includes supply and fitting charges, tools and tackles required for the execution of job along with the cost of material including transportation charges besides charges of installation and all the taxes as applicable, p/fitting of new 2 nos. temperature indicator (wti and oti) with control system in place of damaged. connection of all the control system from buchholz relay and winding of transformer to ht panel no. 1 to ensure the safety and smooth operation of the transformer with copper control cable 8-core 1.00 sq. mm 15 m length approximately with other fittings as per site requirement of any is standard.

CTN :40879488

02 Jul, 2025 2.50 Lacs

Muzaffarnagar - Uttar Pradesh

Tender For bridge unloader - bridge unloader, 1. design, manufacturing and supply of heavy duty out door bridge for sugar mill plant cane unloading conforming to is:807-1976 & is:3177- 1977 fabricated from m.s. plate section conforming to is:226/2062 steel in box type design with and carriage fitted with wheel of fusion welded having l type bearing housing for long travel (lt) wheel assemblies having span-22.00 mtrs capacity -05ton swl along with dismantling of old existing bridge and erection and commissioning of new bridge old existing cross travel trolley will be used. type of bridge-m.s. plate fabricated box type span-22.00 mtrs, unloading capacity -05 ton swl2. techincal specification:-type of bridge -box type (m.s. plated fabricated), capacity-05 ton swl, unloading capacity -80 to 100 ton cane/hr, utility-sugar cane handling, height of top of top rail from ground-10.00 mtrs, height of lift-12.50 mtrs, wirerope19mm, 6/36 construction fibre wire, long travel speed -23-25 meter/minute, box side plate height-1250mm, box side plate thickness8mm, top & bottom plate thickness-top plate-12mm thick, bottom plate-10mm thick, top & bottom plate width-500mm, baff /stiffener plate spacing -750mm, baffle/stiffener plate thickness-8 mm., 3. end carriage:- length-5000mm, height-450mm, centre distance for end carriage wheel-4500mm,centre distance of trolley wheel as per previous trolly.4. long travel mechanism:- size of rail top at long travel- width-60mm, height-25mm, size of rail section at cross travel-width-60mm, hight25mm.5. electric motors for long travel drive 5.3hpx960 rpm rating s4 duty, qty-02 nos.6. gear box for long travel:- type helical,model-hb-350, ratio-40:1, service factor-greater than 2 on installed power, qty-02 no7. coupling for long travel drive:- type geared type half gear model1038. breaks:- thruster-electro hydraulic thruster 18 kg/cm , dia-6", qty 02 no., floating shaft dia/length-70mm/800mm-1000mm9. wheel:- dia meter-420mm, bearing-22218 skf/fag make, housing l type, qty-04 nos, note:- (i)fabrication will be done using prime plates and sections and using mig, welding process. (ii)only tack welding will be done by electrode using arc welding(iii) parallelist of the cross travel rails/square bar, diagonals, deflection of the bridge & trolley will be accurate and confirming to standard and best engineering practices. (iv) bridge must be two coated by red oxide metal primer and two coats of golden yellow colour.11. electric panel for new bridge, resistance boxes for bridge motors, control cabin,12. electric wires, main switch push button control & cable trolleys for complete13. unloader.14. dismantling of old trolly and all its accessories and erection & commission of new trolly, frame and fitting of all old spares ie. rope, drum, thruster break etc complete testing and trail., scope of work1. supply of above mentioned bridge on for basis to mill site.2. dismantling of old unloader. 3.erection of new unloader bridge with old trolley & grab with complete electric work with new electrical panel for bridge and all electrical panel for trolley & grab. all wiring should be new & standard isi make

State Government

CTN :40872507

14 Jul, 2025 1.26 Crore

Multi City - Karnataka

Tender For re babbiting-dismantling of bearings and pads from housing,rebabbiting of 10 nos tgb thrust pad along with all accessories,rebabbiting of turbine guide bearing, mid bearing & end bearing along with floating seals and all accessories,material composite test, ut test and dp test should be done for re-babbitted material,assembly of re-babbited bearings with blue match,submitting the video graphs of re-babbiting and reports of re-babbiting.re-alignment-the reason for shifting of generator shaft by 2 to 3 mm shall be analyzed and rectification works needs to be carried out,complete dismantling, assembling, painting and re-alignment of machine shaft,inspection of turbine shaft journal surface and repairs if required,inspection/replacement of worn out bushes and seals of guide vane, if necessary,inspection and repair of labyrinth ring, face plates, guide vanes and runner,guide vanes bed setting,tgb water cooler descaling work to improve the efficiency of cooler,complete assembly of machine,checking the magnetic axis of the generator and to ensure its alignment, checking of the unit leveling at all places and complete alignment of machine shaft,testing & commissioning of complete machine,painting of entire machine,checking of vibration & site balancing of machine,submission of vibration, balancing & alignment reports.flow switch-supply and installation of flow switch (flow rate110 lpm) along with 01 no 01 nc contact for inlet and outlet lubrication oil pipelines,supply and installation of pressure switch (30bar) for inlet and outlet lubrication oil pipelines,supply and installation of level switch for in tgb oil sump.replacement of new miv trunion shaft-dismantling of miv counter weight, miv servomotor assembly, and other related parts,lifting of miv from the bed,transportation of miv to the firms place, if required,replacing old nitrile rubber trunnion seals with existing profile by new one on both sides,replacements of miv trunnion shaft. providing of necessary drawings,material composite test, ut test and dp test should be done for new trunnion shaft & trunnion seals, bushes etc,all related fasteners and dowel pin to be replacing by new one,drive and non drive end trunnion bush, cupseals, stop end plate, washer ring etc need to be replacing by new one,repair of miv discand main body to be attended, if required,supply and replacement of miv disc rubber seal,pressure testing and commissioning should be carried out as per standard in presence of kpcl engineers,all tools & tackles required for the above mentioned works shall be arranged by contactor only.

Central Government/Public Sector

CTN :40842864

05 Jul, 2025 NA

Bathinda - Punjab

Tender For supply of drive shaft , intermediate shaft , driven shaft , coupling pin with nut

CTN :40812448

14 Jul, 2025 NA

Delhi - Delhi

Tender For supply of electro hydraulic thrustor brake complete set along with break shoe liner type mdt 150 dash 18 , mechanical end stopper for lt motion of crane , ms floating shaft 100 mm dia , auto phase seq corrector 20 hp capacity with double contactor system , auto phase seq corrector 17 decimal 5 hp capacity with double contactor system , changeover 125 amp 4pole , power contactor mn 12 , electro hydraulic thrustor brake complete set along with break shoe liner type mdt 300 dash 34 , pendent push button station 8 way along with push button 08 nos on and off switch , pendent push button station 12 way along with push button 12 nos on and off switch , single phase preventer vsp2 make in india , gear break drum coupling 200 mm dia with s2 bolted , gear break drum coupling 250 mm dia with s2 bolted , rotary type geared limit switch ratio 48 by 1 with 2 contact type grls 48 by 2 se ip 54 , shrouded copper conductor busbar 160amp , supply of desert cooler powder coated body required foundation ground support all as directed at site the entire satisfaction of the board officer , supply of self supporting stand for evaporative air cooler desert cooler all as per the site requirement made out of angel iron at site the entire satisfaction of the board officer

CTN :40715880

07 Jul, 2025 NA

Pathankot - Punjab

Tender For supply of oil seal , ring , cup seal , dcb switch , fuel flexible pipe , wheel bolt , driven shaft , pipe , clamp 10x7 , bolt hex , stopper cable , pressure gauge , temperature sending unit , seal and spg set

Driven Shaft Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Central Government/Public Sector

State Government

Central Government/Public Sector