Latest earthmat Tenders | Government earthmat Tenders

State Government

CTN :45477581

23 Jun, 2026 1.53 Crore

Multi City - Andhra Pradesh

Tender For strengthening of earthmat by providing additional 100x16mm ms/gi flat, 75x12mm ms flat, 75x12mm gi flat, 40mm ms rods and additional new earth pits to minimize /nullify equipment damages during fault periods at 220kv gajuwaka ss under rmi 24-25

corporations/Associations/Others

CTN :45445697

19 Jun, 2026 15.14 Lacs

Kaushambi - Uttar Pradesh

Tender For supply of materials and erection for shifting of control room pannel at 33/ 11 kv sub station bharsawa distt. kaushambi under deposit scheme on "semi turnkey basis" under edc, kaushambi - name of work: supply, carriage & erection of materials for control room pannel shifting of shiffting of 33/11 kv s/s bharsawa distt. kaushambi, supply of de-centralised materials, 11 kv 3x120 mm2 xlpe cable jointing kit o/d & i/d, control cable 4x2.5 mm2, control cable 2x2.5 mm2, g.i. pipe 6 " dia, rubber matting, clamp with nut & bosts, earth wire clamp for pcc pole, stay clamp for pcc pole, top channel clamp pcc pole, dropper channel clamp pcc pole, g.i. strip 35x6 mm, carriage of following material, pcc pole 8.5 mtr. long., structure of la, 33kv isolator, 33 kv cts, single t/f control pannel, 33kv vcb,11 kv outgoing. incoming pannel, battery & battery charger and other associated accessiories etc. (availibility at concern store center of store division), erection work, installation of 33 kv single transformer control pannel 2 no., incoming 2 no. and 7 no. outgoing in the switchgear room and grouting the pannel by rag bolt using cement, sand mortar in ratio 1:3. work includs fitting of all accessories in all respect with complete connection of control cable with pannel. all material will be provided by the contractor except vcb and crp., construction of cable trenchs with top cover and laying of control cable for vcb, c.t. & t/f control pannel etc. as per direction of engineer. trenchs to be 12 wide and 9 deep. work includes digging, of trench, concreting of the foundation in the ratio 1:3:6 r.b. wall 9 wide with cement mortar 1:4 and plastering inside the trench in the ratio 1:3 and sand filling in the trench. all material will be provided by the contractor., earthing of 11 kv indoor equipments, switchgears as per resspo drawing. with g.i. strip of size 35x6 mm. g.i. strip fully welded at both ends and to be connected with earthmat,, erection of dp with pcc pole 8.5 mtr long with all accessaries and grouting of the pcc pole with cement, sand and brick ballast ratio 1:4:8 size 0.45x 0.45x 1.5 mtr deep under the ground as per drawing no. res-6.(cement, sand, brick, ballast shall be provided by the contractor.), installation of 24 volt battery and battery charger with cabinet in the switch gear room, by grouting base channel 100 x 50 x 6 x 1000mm. fixing of rag bolt., laying of 11 kv 3x300/3x185/ 3x120 sqmm. xlpe cable by digging 0.75 mtr. deep trench, putting layer of sand in the bottom, ramming it, laying of cable over it rmt and covering the cable from sides and top by laying bricks, finally covering the same by earth and levelling of the same, all the materials, except cable, will be pvovided by the contractor., fixing and termination of outdoor/ indoor heat shrinkable cable boxes of size 3 x300/3x185/3x120 sqmm. xlpe cable. boxes will be supplied by the contractor, sundries ( as per site requirement/emergency work), safe dismantling of 11 kv o/g pannel & received back to store, laying of weasel conductor with the help of aluminium roller by hanging three nos. on each support in a manner taking sufficient care to ensure safety of weasel conductor against rubbing on ground, precaution for safety of crops is also to be taken. the work includes jointing of conductor by providing jointing sleaves, stringing of conductor upto correct sag and binding of conductor with insulators on each support. all material shall be provided by contractor such as jointing sleeve binding wire, armour rod etc.

corporations/Associations/Others

CTN :45328177

05 Jun, 2026 62.00 Lacs

Kaushambi - Uttar Pradesh

Tender For supply of materials and erection for shifting of control room pannel at 33/ 11 kv sub station bharsawa distt. kaushambi under deposit scheme on turnkey basis under edc, kaushambi - name of work: supply, carriage & erection of materials for control room pannel shifting of shiffting of 33/11 kv s/s bharsawa distt. kaushambi, supply of centralised materials, 11 kv switch gear 600/300/5a 350 mva i/c, 11 kv switch gear 200/100/5a 350 mva o/g, 11 kv 3x300 mm2 xlpecable, 11 kv 3x120 mm2 xlpecable, 24 volt battery, 24 volt battery charger, pcc. 8.5 mtr. long for feeder, 11 kv tpmo switch with fixing clamp, 11 kv top channel, 11 kv dropper angle, earthing complete, stay set complete, 11 kv polymer pin insulator, 11 kv polymer disc insulator, 11 kv disc fiting, 33 kv control panel t/f, acsr weasel conductor, supply of de-centralised materials, 11 kv 3x120 mm2 xlpe cable jointing kit o/d & i/d, control cable 4x2.5 mm2, control cable 2x2.5 mm2, g.i. pipe 6 " dia, rubber matting, clamp with nut & bosts, earth wire clamp for pcc pole, stay clamp for pcc pole, top channel clamp pcc pole, dropper channel clamp pcc pole, g.i. strip 35x6 mm, carriage of following material, pcc pole 8.5 mtr. long., structure of la, 33kv isolator, 33 kv cts, single t/f control pannel, 33kv vcb,11 kv outgoing. incoming pannel, battery & battery charger and other associated accessiories etc. (availibility at concern store center of store division), erection work, installation of 33 kv single transformer control pannel 2 no., incoming 2 no. and 7 no. outgoing in the switchgear room and grouting the pannel by rag bolt using cement, sand mortar in ratio 1:3. work includs fitting of all accessories in all respect with complete connection of control cable with pannel. all material will be provided by the contractor except vcb and crp., construction of cable trenchs with top cover and laying of control cable for vcb, c.t. & t/f control pannel etc. as per direction of engineer. trenchs to be 12 wide and 9 deep. work includes digging, of trench, concreting of the foundation in the ratio 1:3:6 r.b. wall 9 wide with cement mortar 1:4 and plastering inside the trench in the ratio 1:3 and sand filling in the trench. all material will be provided by the contractor., earthing of 11 kv indoor equipments, switchgears as per resspo drawing. with g.i. strip of size 35x6 mm. g.i. strip fully welded at both ends and to be connected with earthmat,, erection of dp with pcc pole 8.5 mtr long with all accessaries and grouting of the pcc pole with cement, sand and brick ballast ratio 1:4:8 size 0.45x 0.45x 1.5 mtr deep under the ground as per drawing no. res-6.(cement, sand, brick, ballast shall be provided by the contractor.), installation of 24 volt battery and battery charger with cabinet in the switch gear room, by grouting base channel 100 x 50 x 6 x 1000mm. fixing of rag bolt., laying of 11 kv 3x300/3x185/ 3x120 sqmm. xlpe cable by digging 0.75 mtr. deep trench, putting layer of sand in the bottom, ramming it, laying of cable over it rmt and covering the cable from sides and top by laying bricks, finally covering the same by earth and levelling of the same, all the materials, except cable, will be pvovided by the contractor., fixing and termination of outdoor/ indoor heat shrinkable cable boxes of size 3 x300/3x185/3x120 sqmm. xlpe cable. boxes will be supplied by the contractor, sundries ( as per site requirement/emergency work), safe dismantling of 11 kv o/g pannel & received back to store, laying of weasel conductor with the help of aluminium roller by hanging three nos. on each support in a manner taking sufficient care to ensure safety of weasel conductor against rubbing on ground, precaution for safety of crops is also to be taken. the work includes jointing of conductor by providing jointing sleaves, stringing of conductor upto correct sag and binding of conductor with insulators on each support. all material shall be provided by contractor such as join

State Government

CTN :44929870

04 May, 2026 22.99 Lacs

Multi City - Karnataka

Tender For routine, preventive, breakdown maintenance of ody equipemets i.e breakers, cts, pts, transformers, earthmat, mulsifyre system, hydrant system, dewatering system etc of ee(ody)n division at nagjhari power house for a period of 12 months covering all associated works required for successful completion of the work.

CTN :44759698

16 Apr, 2026 NA

Solan - Himachal Pradesh

Tender For replacement of pls led pc spot lights, dmx controller, repair of six channel dimmer and procurement of cord less mic in auditorium at dr. ysp university of horticulture and forestry nauni-solan.

CTN :44590609

02 Apr, 2026 NA

Solan - Himachal Pradesh

Tender For replacement of pls led pc spot light dmx controller,repair of six channel dimmer and procurement of cord less mic in auditorium at uhf nauni solan

corporations/Associations/Others

CTN :44555002

01 Apr, 2026 1.50 Lacs

Ajmer - Rajasthan

Tender For supply of spare parts of leyland vehicles - various oil seal, various fan belt, brake shoe inner &clutch facing., major & minor repair kit, prop. shaft component s, king pin components, u bolts,i bolts, centre bolt with nut, chassis malleable components shakle ,all. bracket, shakle pin & bushes, high tensile automile fastner, water pump components, automotive rubber parts, all spare relavents to repair of power stearing box & pump, head light assambly head light unit accesaries, automotive bulb, break light, roof light head light, meter bulb, automotive switch flasher 24v h.l.switch 24v dimmer switch 24v, rocking arm 20" rocking blade 20", allu.rivit for facing 40 hole, rivit for slack adjuster, slack adjuster cover plate mei 1676, major rep.kit, minor rep.kit, exhaust monifold nut, exhaust monifold stud, ac crank shim, sump plug, with drawl plate 4 finger, release bearing ff cover, release bearing, housing ff, cap valve steam, cap oil filter (filter cap), cy.liner x bs ii, cy.liner y bs ii, cy.liner z bs ii, main brg.set 0.10, main brg.set 0.20, main brg.set 0.30, main brg.set 0.40, main brg.std, con.road.brg.set 0.10, con.road.brg.set 0.20, con.road.brg.set 0.30, con.road.brg.set 0.40, con.road.brg.std, crank thrust washer, con.road bush bs iii, oil filter bs ii eti, oil filter bs iii, came bush kit, piston assy.bs ii eti, piston assy.bs iii, valve seat exhaust, fly wheel shim thick 14", valve steam oil seal bs iii, cyl.head gaskit mls, ohg kit whg 6 dti-mls, valve grinding rubber, tapper cover packing, return spring for pressure plate, selector plate 3rd, selector plate 1st & 2nd, syncro ring 1st & 2 nd, sliding dog clutch 2nd & 3 rd, sliding dog clutch 4th & 5th, tp cover, filter elbow, syncro cone mk-2nd, sleeve, sleeve for spigot, bearing, syncro kit, selecter pad, helical spring, syncro body 5th & 6 th, input shaft, locking ring, syncro ring 2nd & 4th, syncro ring 5th & 6th, syncro body 3rd & 4th, detent plunger, detent plunger, spring, sleeve reverse, rear nut locking ring, pressure piecl, (plunger), ball pin big, ball pin small, syncro cone mk-2 (2nd & 3rd), selector shaft, selector shaft kit, split ring, syncro cone 1st zf, m.s.4th gear zf, c.s.4th gear zf, input shaft cover bs iii, m.s.5th gear bs iii, l.s.5th gear bs iii, 4th gear ms 24 teeth bs iii, input shaft mk-2, gear box gas kit zf, return spring gear box, split ring 37 mm, u.j cross shim, prop. shaft check nut bsii, front jaw & pin with nut, brake cam sleeve, spacer, brake cam washer, brake cam shim, brake cam lock, frt. axle cotter pin 3 1/2, frt. grease cap packing, king pin gaskit, king pin bush, stud axle, king pin cotter pin big, king pin cotter pin small, tie rod rep.kit bsiii, rear jaw & pin with nut, brake cam sleeve rear, rear diaphram, o ring rear, diapharam tata, brake linear rivits set 80 hole, gear side diff.(sum gear), rear axle shaft packing, rediator cap with chain bsii, clutch socket comp., clutch socket screw, diesel pipe 19χ19, diesel pipe 17χ20, oil flexible pipe, shackle pin lock bolt with nut 1/2 x 2%, rediator hose metal, gear joint assy., battery teerminal p+n, battery lug, battery charging clip, rear view mirror with bracket, rear view mirror, allu. washer flat 6 mm, allu. washer flat 8 mm, allu. washer flat 10 mm, allu. washer flat 12 mm, allu. washer flat 14 mm, allu. washer flat 16 mm, allu. washer flat 18 mm, allu. washer flat 19 mm, allu. washer flat 20 mm, allu. washer flat 22 mm, allu. washer flat 30 mm, allu. washer flat 32 mm, allu. washer flat 34 mm, toggle switch, pull & push switch, wiper wheel box big/small, head light holder 3 pin, self starter switch, l.e.d light yellow 24 volt, l.e.d light red 24 volt, l.e.d light white 24 volt, fuse box 12 poll 24 volt, wiper lock big, wiper lock small, wiper blade 24", wiper arm 24", warning lamp assy., warning lamp bulb, l.t wire 4mm (one role 25meter), l.t wire 6 mm, l.t wire 8 mm, p.v.c tape, cotton tape roll big, wi

Earthmat Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

corporations/Associations/Others

corporations/Associations/Others

State Government

corporations/Associations/Others