Latest eccentric press Tenders | Government eccentric press Tenders

CTN :45693900

10 Jul, 2026 NA

Mumbai - Maharashtra

Tender For supply and installation of automobile trainers and equipment at consignee locations. (tender ref no.26008/2026-27) - light motor vehicle driving simulator, injector -multi hole type, pintle type, petrol engine - 2 stroke, motor cycle/ scooter, injector cleaning unit, injector testing set (hand tester), fuel feed pump for diesel, fuel injection pump - diesel - inline, fuel injection pump - dismantling tool kit, fuel injection pump - distributor fuel rotary pump with standard accessories, fuel injection pump - ve pump with standard accessories, cylinder liner- dry & wet liner, cylinder liner - press fit & slide fit, steering assembly - rack and pinion, air brake trainer assembly, alternator assembly - lmv, engine bearing model set, piston model set, front axle assembly, rzeeppa joint with stand for dismantling and assembly, full floating axle and semi floating axle assembly, wiper motor assembly, cut section model - 4 cylinder diesel engine, cut section model - automatic transmission gear box, cut section model - centrifugal clutch assembly, cut section model - diaphragm clutch assembly, cut section model - radiator - cross flow, cut section model - radiator - down flow, cut section model - shock absorbers, cut section model - single plate clutch assembly, cut section model - turbocharger, demonstration board - anti theft device car, automotive safety air bag simulator, car air conditioner trainer, demonstration board - crdi system, demonstration board - electronic ignition system and ignition coil, disk brake trainer, drum brake trainer, working model - power windows, working model - torque converter, denting kit set, engine compression tester (diesel), two post car lift- capacity 4 ton, electric operated, radiator pressure tester, tyre changer machine, tyre air pressure gauge with holding nipple, wheel alignment machince computerized 3d, wheel balancing machine (for wheel balancing of lmv), air conditioning service unit - car, automotive battery charger, automotive battery tester/ analyser, battery terminal cleaner tool, air blow gun, air impact wrench with impact sockets, engineers stethoscope, grease gun - 500 grams, oil can 500 ml, oil filter wrench - upto 500 mm, piston ring compressor - 50 - 100 mm, piston ring expander and remover - 50 - 100 mm, piston ring groove cleaner, belt tensioner gauge, car jet washer with standard accessories, auto electrical work bench, gloves: rubber, gloves: cotton, industrial/ safety shoes, industrial helmet, blow lamp: 0.5 liter, magnifying glass: 75 mm, lifting tackle/ sling: 1 ton, 2 meters, laser distance measuring instrument, demonstration board: electric vehicle cooling system, engine and transmission system for electric vehicle, cut section of electric vehicle motors, hvac trainer, electric vehicle service equipment test adapter kit, battery tester with inbuilt printer, lighting and wiring system for electric vehicle, electric vehicle diagnostic scanner, solar based charging system, electric vehicle tool kit, electrically insulating blanket, clamps for insulating blanket, insulated rubber mats, gloves: electrically insulated, industrial/ safety shoes: electrically insulated, glove inflator kit, goggle: white glass, ac current digital clamp meter, digital continuity tester, soldering iron set: mechanic electric vehicle

CTN :45705038

07 Jul, 2026 8.00 Lacs

Ahmedabad - Gujarat

Tender For auction sale of flat - all parts and parcels of non-agriculture immovable residential flat no.b-503 having carpet area 36.08 sq mt, super built up 42.27 sq mt, undivided shareof "ashopalav residency land 14.79 sq mt, undivided share of common road 2.56sq mt & undivided share of common plot 1.93 sq mt which is on 5th floor of b tower constructed on na land bearing block no.230 admeasuring 21144.00 sq mt paiki eastern part reserved for owner known as coat no.1, coat no.2, coat no.4 of"press coat residency", revenue survey no.318/1 and 327 situated in scheme named "ashopalav residency" at village: kapurai, ta. vadodara, district: vadodara of gujarat state with is bounded as under; east: ots & flat no.a-560 of tower-a. west: common passage & flat no.b-504. north: common passage, ots & lift. south: block no.214/2.

CTN :45688862

16 Jul, 2026 57.20 Lacs

Visakhapatnam - Andhra Pradesh

Tender For tender for supply of guide ring , elastomeric spring , shaft intermediate , nozzle 11 hole , hand pump , spring washer , washer spring b12 , rotary seal , rubber mount , buffer , contact cleaner spray , circlip , circlip 72x2.5 , pressure monitor , plug , screw , screw , screw , screw , cylinder roller bearing , butting washer s63 x 80 din 988 , toothed quadrant , screw , turbo charger , washer , o ring , o-ring , o ring , oil filter , air filter element , woodruff key 2 x 3 , 7 din 6888 , rectanglr-sect ring , ring sealing a16x20 , ring sealing (crank case) a48x55 , shaft seal , shaft seal , tachometer , radial-lip shaft seal , crankshaft , seal 50x78x1.5 din71511 , hylomer sq 32m , sealing paste gd block , gasket , pipe , sealing tube , valve inner , exhaust valve , valve inlet , seat ring valve inlet , bush guide , guide tube assy , gasket , water pump shaft , pipe , gasket , seat ring valve , spring retainer , leak off fuel line , press relief valve , pressure relief vv 5.5 bar , pressure relief vv 2.5 bar , pipe , retaining tube , thrust ring , o ring , impeller , o ring , gasket , connecting piece , sealing ring modified , oil pump , valve exhaust , valve guide , packing plate , nozzle holder with nozzle , ring sealing , cylinder head w/valve , cover , spacee plate , track ring , pushrod exhaust , gasket , gasket , damper strip , fuel priming pump , gasket , impeller , gasket , high pressure line , gasket , hp line , mtu test kit , complete , o ring , sleeve rubber , o ring 9.2x2.62 , o ring 11x25 , o ring 15x5 , o ring , o ring 31x2.5 , o ring 32x4 , o ring 36x5 , o ring 37.46x533 , o ring 46x2 , o ring 75x5 , o ring 80x6 , o ring 84x3mm , o ring , o ring 90x4 , o ring 105x3.5 , o ring 18x4 , o ring 6x2.5 mmn 429 , o ring , o ring , gasket 57 x 2 mmn 489 , hose line , cam shaft drive gear , idler gear assembly , bearing bush , spare parts kit , pump element , plate , spare part kit k37 , bolt , washer , compensating washer , compensating washer , compensating washer , shim , compensating washer , compensating washer , shim , spring , o ring 76 x 2.5 , coloured screw , hose clamp , adaptor , element fuel filter f.f-0023 , hose clamp , nut , snap ring , rubber bellows , thermocouple , trackball , tachometer , pressure sensor , pressure sensor , top compr.ring st w6 , fuel pump complete , screen , mpc1-01 computer , plug-in board , bib 1 , plug in board cib 3-10 , display dis 10-01(5105381275/s0004) , valve exhaust std floating bridge , ros 2-03 control lever , multi led t5 , 5k24 red , wiring harness to injector , module mcs-5/pim3 , module pim2 measure/monitor mod , modular system , plug-in-board , housing , test unit , hp pump , electronic gover ecu4-04 (e5275304760/76) , sea water pump , starter , injector , bearing body , tester , pressure sensor , gasket

State Government

CTN :45695563

03 Jul, 2026 NA

Nicobar Island - Andaman And Nicobar Islands

Tender For maintenance of iei and eei to the directorate of tribal welfare building under section-ii of sub division-i during 2025-26. sw supply of materials - frls pvc insulated copper conductor cable 1.5 sq mm. make: anchor/havells/ polycab/ rr kabel., frls pvc insulated copper conductor cable 2.5 sq mm. make: anchor/havells/ polycab/ rr kabel., frls pvc insulated copper conductor cable 4.0 sq mm. make: anchor/havells/ polycab/ rr kabel., fan capacitor 2.5 mfd (oil). make : havells/universal or equivalent., led batten suitable for 20 w led tube. make: havells cat ref. : regalbattent8upto1x22w ssbswh equivalent., p.t switch 6 amps. make : anchor penta urea/ havells reo range (white)., p.t socket 6 amps, 2 in 1, 5 pin. make : anchor penta urea/ havells reo range (white)., p.t bell push. make : anchor penta urea/ havells reo range (white)., p.t switch 20a. make : anchor penta urea/ havells reo range (white)., p.t socket 20a & 10a uni socket. make : anchor penta urea/ havells reo range (white)., one module step type fan regulator. make : anchor penta urea/ havells reo range (white)., two module step type fan regulator. make : anchor penta urea/ havells reo range (white)., 6a batten holder. make : anchor penta/ havells reo range (white)., 6a ceiling rose. make : anchor penta/ havells reo range (white)., call bell (ding dong type/ musical type) make: pressfit, code:712190 or equivalent., pvc gang box 2 way (for 15/16a s/socket) make : press fit or equivalent., pvc gang box 1 way (for 05/06a s/socket) make : press fit or equivalent., pvc gang box 2 way (for 05/06a s/socket) make : press fit or equivalent., pvc gang box 3 way (for 05/06a s/socket) make : press fit or equivalent., pvc gang box 4 way (for 05/06a s/socket) make : press fit or equivalent., pvc gang box 5 way (for 05/06a s/socket) make : press fit or equivalent., pvc gang box 6 way (for 05/06a s/socket) make : press fit or equivalent., pvc gang box 8 way (for 05/06a s/socket) make : press fit or equivalent., pvc conduit pipe 20mm (mms) make : precision or equivalent., pvc conduit pipe 25mm (mms) make : precision or equivalent., pvc 01 way junction box 20 mm (mms) make : precision or equivalent., pvc 02 way junction box 20 mm (mms) make : precision or equivalent., pvc 03 way junction box 20 mm (mms) make : precision or equivalent., pvc 04 way junction box 20 mm (mms) make : precision or equivalent., pvc 01 way junction box 25 mm (mms) make : precision or equivalent., pvc 02 way junction box 25 mm (mms) make : precision or equivalent., pvc 03 way junction box 25 mm (mms) make : precision or equivalent., pvc coupler 20 mm (mms) make : precision or equivalent., pvc coupler 25 mm (mms) make : precision or equivalent., pvc bend 20 mm (mms) make : precision or equivalent., pvc bend 25 mm (mms) make : precision or equivalent., pvc elbow 20 mm (mms) make : precision or equivalent., pvc elbow 25 mm (mms) make : precision or equivalent., pvc tee 20 mm (mms) make : precision or equivalent., pvc tee 25 mm (mms) make : precision or equivalent., pvc square box/ junction linker (mms) make : press fit or equivalent., pvc channel 20mm (mms) make : press fit or equivalent., pvc channel 25mm (mms) make : press fit or equivalent., pvc channel 32mm (mms) make : press fit or equivalent., pvc insulation tape 18mm (red, yellow, blue, green, black). make : precision or equivalent., ac ceiling fan 1 star rating with isi mark, 1200 mm sweep. make : crompton, energy saving or equivalent., wall fan, 400 mm. make : crompton, hiflo neo or equivalent., exhaust fan, 250 mm, make : crompton, brisk air neo or equivalent., b series sp mcb 6 a-32 a, make: havells cat ref. dhmgbspf006-032 or equivalent., c series sp mcb 6 a-32 a, make: havells cat ref. dhmgcspf006-032 or equivalent., isolator 40 amps, four pole, make: havells cat ref. dhmgifpx040 or equivalent., isolator 63 amps, four pole, make: havells cat ref. dhmgifpx063 or equivalent., pvc wall grip, m.s screw 1", m.s screw 1 1/2", ball bearing 6201 (make : skf

CTN :45646934

07 Jul, 2026 2.25 Lacs

Thiruvananthapuram - Kerala

Tender For one panchayath one playground -development of jai hind stadium in njarackal grama panchayath in vypin lac, ernakulam district-supply and installation of open gym equipment - outdoor gym equipments, od268048/2025-2026 chest press (double) - supply and installation of double chest press having the following specifications: dimensions: (l x w x h) 1955 x 710 x 1900 mm. main center pipe - ø 114 mm od “b” class gi pipe. foundation plate –m.s. round plate of ø 250mm & 8 mm thick. foundations cover capdome shape of pp / nylon / hdpe material. remaining frame -made up of ø 48 mm od “b” class g.i. pipe. handle - made up of ø48mm od “b” class g.i. pipe. link - made up of ø 48 mm od “b” class g.i. pipe. seat & back rest – 380 x 275 x 60 mm thick high-density polyethylene (hdpe) blow molded with m10 in-sert wall thickness 3 to 4 mm. bearing bush closing cap’s– pp / nylon / hdpe material. handle must be connected with frame by 8 mm laser cutting ms profile. top closing cap – dome shape made by pp / nylon / hdpe material. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe.height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing - use is 6005 permanent lubricated reputed brands. pin – made up of ø 25 mm m.s. bright bar pin. bearing bushes - ø 60 mm od seamless pipe. grips - high quality rubber ø 46 mm od. circlips–a 24 circlips are used for assembly. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od268050/2025-2026 air walker - supply and installation of air walker having the following specifications: dimensions: (l x w x h) 1190 x 380 x 1244 mm. main frame- ø 88 mm od ?b? class gi pipe dually bending design. foundation plate?m.s. round plate of ø 250 mm & 8 mm thick. paddle? ø 42 mm od round gi pipe. handle ? ø 33 mm od ?b? class gi pipe. footrest - cast iron 124 x 296 x 5 mm thick and m.s. plate of 2 mm thick use to support it. top closing cap ? dome shape made by pp / nylon / hdpe material. closing cap?s -pp / nylon / hdpe material. bracket - 8 mm thick laser profile is use to support paddle frame. foundation stool: made from main pipe ø 88 mm od m.s pipe and top support of m.s. round plate of ø 250 mm & 8 mm thickness is welded top. square tube of 30 x 30 x 2 mm must be used to support center pipe.height of stool is 3 ft. foundation stool is embedded in c.c. stock below ground level. bearing- use is 6005 permanent lubricated reputed brands. pin?s ? ø 25mm m.s. bright bar pin. circlips? a 24 circlips are used for assembly. bearing bushes -ø 60 mm od seamless pipe. coating - best quality of powder coating 80-120 micron. safety instructions and exercise chart - start & finish position stick on product. all joints must be welded as per is standards and zinc primer paint should be applied at all the welding points prior to finishing. (foundation shall be m20 cc and design shall be approved by the engineer-in -charge before installation.), od268054/2025-2026 rower - supply and installation of rower having the following specifications: dimensions: (l x w x h) = 1472 x 915 x 1040 mm. upper and bottom pipes - 88 mm od b class gi pipe. foundation plate m.s. round plate of 250 mm & 8 mm thick. handle - 33 mm od b class g.i pipe. angle between handle and horizontal surface is 75 - 80 degree. linkages 48 mm od b class g.i. pipe.seat & back rest 380 x 275 x 60mm thick high-density polyethylene (hdpe) blow molded with m10 in-sert wall thickness 3 to 4 mm. foot resting pipe - 60 mm od b class g.i. pipe. e

CTN :45492754

24 Jun, 2026 4.50 Lacs

Leh - Jammu And Kashmir

Tender For corrigendum : supply of retainer , rivit bird cage , cover , pan om , clip , plug rockersw , cover hvac , insert threaded , cap end , knob , sleeve , bumper , instruction , bushing keyed , bushing , clevis rod end , spring centering , pin hardende clevis , stand seat , foam panle , foam edge , foam panel , panel lh , cover pan flor , foam front , boot , foam pan floor , pedal assy lh , hinge rear door , handle latch door , retainer plastic , roller , stop , channel , stud weld on , grip lever , plug , pin pivot tapered , knob clamping , bushing wear , fitting grease , damper , bushing weld on , bushing pivot , ftg grease strainth , ftg grease 90 , ftg grease straght , spring compression , lever tach , pin , cover drain , plug recessed pipe , link , gasket liquid , cover access , cover plate , bearing axle , key wood ruff , vent breather , bushing press fit 5 , mount man fold drain , fitting hyd connector , clamp , mount bulkhead , strap , clamp tube khead , tee , fitting hyd elbow , clamp hose , decal danger , strap tie , clamp 10 , spacer tube , mount valve , mount boom down , handle control , adapter hyd , seal bushing , pin clevis , pin hair * /bid number : gem/2026/b/7640814 + /dated: 09-06-2026 ' ' / bid document 1 / 66

Corporations/Associations/Others

CTN :45637028

26 Jun, 2026 NA

Lonavala - Maharashtra

Tender For invitation of e-quotation for the procurement of open-gym equipment for all parks in lonavala city and for the supply of casting benches to various wards within the city. - open-gym equipments, surf boardtechnical specifications length :- 1850mm wdth :- 1100mm height :- 1690mmsafe area :- 3.07 x 2.32 meter surf board equipment made up of b class gi pipe of different nb. nb stands for nominal boar size i.e. internal diameter of pipe in millimeters. make of gi pipe will be of tata, jindal, and swastik. the main frame pipe is 80 nb of arc bend dia 1590 mm.handle frame is made up of 25 nb with radius of 740mm.handle support made up of 25 nb pipe.prime stand base are made up of ms round plate 250x8mm thk, prime stand base plate have round slot slots. welded to main frame with a triangular notch 75x50x5 mm thk. prime stand supporting bush is of dia 140mm.main paddle support bearing bush made of dia 140mm.pedal bearing bush support plate dia 130 x 60 bore x 8 mm thk.pedal is made up of 40 nb pipe with serpent shape of 3 bend, to avoid stress on pipe & increase bearing life, avoiding stress on bush.pedal movement restricted to 120 by specially designed mechanism.drum closed with dia 140 x 3 mm thk plate.to build bushes seamless pipe of od 70mm & 6mm thickness used.the pins used are made up of en-8 35mm.the bearings are used 6007-2rs1 permanent lubricated bearings. bearings are used reputed brand (skf/fag).the circlips a34 used for assembly., thi chi spinnerstechnical specifications length :- 1050mm width :- 850mmheight :-2000mm safe area :- 2.27 x 2.07 meterthi-chi spinner made up of b class gi pipe of different nb. nb stands for nominal boar size i.e. internal diameter of pipe in millimeters.make of gi pipe will be of tata, jindal, and swastik.the main frame pipe is made up of 50 nb with semi arc bend of r4.3 meter.prime stand base is made up of ms round plate 250x8mm thk, prime stand base plate have round slot holes, welded to main frame with a triangular notch 75x50x5mm thk supporting pipes welded to main frame size 40x40x2.5mm thk wheel connection link is 25 nb curve bend made up of b class of g.i. pipe.wheel of dia 450 mm gi plate with 1.2 mm thick with collar.wheel support is made up of 25x25 sq pipe which also welded to bush.to build bushes seamless pipe of od 60mm & 6 mm thickness used.the pins used are made up of en-8 25mm & 12mm. the bearings are used 6205 permanent lubricated bearings., leg press machine technical specificationslength :- 1760mm.width :- 1500mmheight :- 1420mmsafe area :- 2.96 x 2.7 meterleg press equipment made up of b class gi pipe of different nb. nb stands for nominal boar size i.e. internal diameter of pipe in millimeters.make of gi pipe will be of tata, jindal, and swastik.the main frame pipe is 80 nb with arc bend of r795mmprime stand base are made up of ms round plate 250x8mm thk, prime stand base plate have round slot holes. welded to main frame with a triangular notch 75x50x5 mm thkprime stand supporting bush is size of dia 140mm.main paddle support bearing bush is size of dia 140mm.drum closed with dia 140 x 3 mm thk plate.to build bushes seamless pipe of od 60mm.the pins used are made up of en-8 material 35mmthe bearings are used 6007-2rs1 permanent lubricated bearings.the circlips a-34 used for assemblypedal bearing bush support plate dia 125 x 60 bore x 8 mm thk plate pedal is made up of 40 nb pipe with serpent shape, to avoid stress on pipe & increase bearing life to avoiding stress on bush.pedal movement restricted to 120 by specially designed mechanism.the footrest frame is made up of 25 nb of b class of g.i. pipe with l shape bend.footrest support is made by 50x50x3mm ms square pipe. the footrest made from pc material of size 305x125x5 mm, & assemble with the support of 250x115x3mm thick ms plate., chest cum seated pullertechnical specifications length :- 2460mmwidth :- 970mm height :- 2270mmsafe area :- 3.68 x 2.19 meterchest cum seated puller equipment made up of b

corporations/Associations/Others

CTN :45624244

26 Jun, 2026 4.67 Lacs

Chandigarh - Chandigarh

Tender For providing and fixing of open air gym equipments in various parks of sector 20,chandigaarh under ward development fund. - providing and fixing of chest press double size / dimensions length -1200 milimeterwidth- 700 milimeterheight 1800 milimetermaximum weight -120 kilogrammaterial:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength, durability, and corrosion resistance. the main central pipe shall be an 80 mm nb gi pipe, while the handle frame and sheet frame shall each consist of 40 mm nb gi pipes. the connecting links shall be made of 32 mm nb gi pipes, and the footrest pipe shall also be 32 mm nb gi. the mild steel (ms) foundation plate shall have a minimum thickness of 12 mm. the foundation pipe shall consist of a gi pipe anchored 750 mm deep and supported with an ms angle of 25 25 4 mm for stability. the seat and backrest shall be made of high-density polyethylene (hdpe) sheets with a thickness of 3 mm, designed with a uniform bending radius to avoid sharp edges and ensure user safety. all nuts and bolts used for assembly shall be made of galvanized iron (gi) to enhance durability and resistance to corrosion. the movement mechanism shall be fitted with ball bearings that are self-lubricating and sealed to protect against rain, dust, and other environmental elements. the closing caps of open ends of all pipes, as well as bearings, bushes, and bases, shall be covered with fibre-reinforced plastic (frp) closing caps having a minimum thickness of 3 mm. all plastic components shall be uv-stabilised and weather-resistant to ensure long-lasting performance in outdoor conditions.colour:- green paint finish- power coated, uv resistantpaint coating thickness (min) 100 micrometerwarranty 3 years.complete in all respects, including installation of equipment in a cement concrete block of size 5 x 5 x 1 , to the entire satisfaction of the engineer-in-charge., providing and fixing of leg press leg shaper complete in all respects having following specifications.a) all pipes should used in the equipments should be galvanised with 3mm thickness.b) multi colour powder coating with polyster paints should be used on all the equipments.c) the foot pedal on all the equipments should be of aluminium only.d) the seats should be made of high quality plastic with colour scheme in yellow or orange.e) the high end bearings such as skf/nbc must be used in all the equipments.1 dimensions- 1730*450*1450mm2 colour- customizable multi colour and complete powder coat3 size of main tube-114*3.75mm steel pipe4 size of supporting tube-76*3mm steel pipe5 there is restrainer inside, the distance between swing arm and main tube is greater than 230mm avoiding the danger of getting stuck.6 al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 anti-skid components are used at the pedal parts.8 the distance between two spinners is no less than 230mm, avoiding the damage of being stuck9 anti theft cover is made by stainless steel/high quality plastic.10 thickness of bearing bracket is no less than8mm11 hazardous materials like coating agent, rubber are under national newest standard.functions: develops the strength of lower limbs, and improves the stability and agility of three main joints of lower limbs; good for the healing of inconvenience of bending and stretching of lower limbs, and muscular atrophy of lower limbs, rheumatoid arthritis, sciatica, sprain of the anklebone, etc. approaches: sit on the chair and step on the footboard. stretching legs with force and recover slowly. repeat. users: suitable for people of different ages.complete in all respects, including installation of equipment in a cement concrete block of size 5 x 5 x 1 , to the entire satisfaction of the engineer-in-charge., providing and fixing of parallel bars size/dimensionslength- 900 millimeterheight 800 millimetermaterial:- all the pipes shall be galvanized iron (gi) and isi marked to ensure strength and durability. the ver

Central Government/Public Sector

CTN :45616776

20 Jul, 2026 NA

Ajmer - Rajasthan

Tender For supply of interchangeable threaded insert 1/4* bsp male to 1/4* female hydraulic nut for automatic hydraulic bearing extractor machine used for press out of roller bearing bearing no. 22326 c/c3 of bore size130 mm [ warranty period: 30 months after the date of delivery ] ]

State Government

CTN :45625466

02 Jul, 2026 16.05 Lacs

Gautam Budnagar - Uttar Pradesh

Tender For providing and fixing of open gym equipment and g.i chain link fencing open gym in village chanchali yea wc-6 - sit up station: providing, designing and fixing of double sit-up station of size 1500 x 1150 x 650mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe of 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using akzo nobel or equivalent of 80 - 120 micron thick. all joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. seat and base plate cover to be made up from virgin lldpe manufactured by rotational molding with minimum thickness of plastic as 8mm, colorful and uv resistant and environmental friendly. the equipment to be fixed on ground with concrete of minimum strength m-25 and j shape welded bolts and once the concrete is set, fix the equipments on to it and cover nuts and bolts with the base plate. all complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base pedal) and fixing of equipments etc. (the cement concrete and excavation work shall be paid separately). (ar/yeida/uppwd/sor-2020), leg press: providing, designing and fixing of leg press of size 2000 x 550 x 1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using akzo nobel or equivalent of 80 - 120 micron thick. all joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. handle bars to be provided with high quality grip rubber on top end. pedals shall be made up of nylon alloy with rounded edges to prevent any impact of injury. seat and base plate cover to be made up from virgin lldpe manufactured by rotational molding with minimum thickness of plastic as 8mm, colorful and uv resistant and environmental friendly. bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted with inbuilt limiters to prevent unwanted movements. all open ends of pipe to be closed by gi/ lldpe caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m-25 and j shape welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate. all complete as per direction and approval of engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipments etc (the cement concrete and excavation work shall be paid separately). (ar/yeida/uppwd/sor-2020), seated chest press: providing, designing and fixing of seated chest press in a pair of size 1800 x 700 x 2000 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipe 40mm dia and 2.5mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using akzo nobel or equivalent of 80 - 120 micron thick. all joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. handle bars are to be provided with high quality grip rubber. pedals shall be made up of nylon alloy with rounded edges to prevent any impact or injury. seats and base plate cover to be made up from virgin lldpe manufactured by rotational mounding with minimum thickness of plastic as 8mm, colorful and uv resistant and environmental friendly. bearing used shall be maintenance free, duly oil sealed and self lubricated made by reputed company to be approved by engineer in charge. equipme

Eccentric Press Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Corporations/Associations/Others

corporations/Associations/Others

Central Government/Public Sector

State Government