Tender For repair/replacement of external electric supply distribution network with other connected items at malad, marve and kandivali under ge (n) santacruz, mumbai - supply, install, testing & commissioning pedestal cubical type double door lt bus bar chamber box of suitable size factory made modular construction fabricated out of 3 mm thick crca sheet, angle iron, channels, epoxy powder coated to give a superior finish , outdoor type , totally enclosed dust & vermin proof with locking arrangements front & back side opening system including rain shed, busbar chamber should be suitable for accomodating all aluminium bus bar strips (50mm x 10mm x 04 nos) & gi strip for earth fixed on porcelain insulators, and one independent metering module suitable for accomodating three phase volt meters & ammeter digital type, indicator lamps, cable entry/exits cut outs at bottom part, with fixing arrangement on pcc (1:3:6) type c-2 bed block with studs, bolts, nuts & washers, danger notice board with scull suitable for 415 volts or required size to be fixed on pannel including dismantling of old bus bar panel all as specified and directed by engr-in charge.notes:-(a) aluminium bus bar duly covered with colour coded shrinkable sleeves of required size for phases and neutral - 01 set(b) mccb 4 pole , ics=100%icu- 25 ka, 415 volts, 100 amps , with thermal adjustable and fixed magnetic setting with extended terminals -02 nos.(c) digital multifunction meter of size 96x96 mm to measure current, voltage, frequency and power factor with built in selector switch and programable ct of appropriate ratio.-01 no make- imp/automatic electrical(ae)/ l&t / havells/ meco(d) panel indicating lamp neon/led type (red ,yellow & blue) with lamp holders - 03 nos(e) panel instrumental wiring with frls suitable size but not less than 2.5 sqmm copper wire single core - 01 job(f) necessary sizes of lugs for fixing of cables in bus bar deemded to be included rate quoted by the contractor.make of mccb & mcb: larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 400 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:- larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 160 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 16 ka 100 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 250 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb all as specified and directed by engr-in-charge make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supplying, laying,connecting, testing & commissioning lt ug pvc insulated, heavy duty, 1100 v grade electric cable with aluminium conductor of size 16 sqmm x 4 core, laid in trenches or passing through pipe or fixed to wall, making all connections with and including provision of necessary glands, lugs, bushing etc as required including taking down old unserviceable cable complete all as specified and as directed by engineer-in-charge of following sizes:-note : earthwork excavation, dwc
Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - annual overhauling of c&i equipment’s for - box spanners (mm & inches), size up to 50-min. 4 sets, ring spanners (mm & inches), size up to 50-min. 4 sets, de spanners (mm & inches), size up to 50-min. 20 sets, slide wrench 6", 8"- min. 20 sets, slide wrench 12"-min. 10 sets, pipe wrench 300 mm min. 5 sets, pipe wrench 450 mm min. 5 sets, combination pliers - min. 20 sets, mini connector (taparia make) - min. 20 sets, 1. screwdriver sets-min. 20 sets, - champion set - min. 20 sets, . connector taparia (932) - min. 20 nos, . watchmaker set - min. 5 sets, . junior hacksaw with frame - min. 20 sets, 6. teflon hammer - min. 5 sets, 6. ss tube cutter-min. 5 sets, . slide cutting pliers-min. 20 sets, nose pliers-min. 20 sets, . soldering iron - min. 2 sets, multi meter with all function (fluke) - min. 20 sets, ma source-min. 2 nos, wire stripper-min. 20 sets, flat screwdrivers (small/medium/large) - min. 20 sets, led torch light (good quality)-min. 20 sets, allen key set (mm & inches), normal sizes-min. 20 sets (each), portable drilling machines with bits-min. 3 nos, portable grinding machines with wheels-min. 4 nos, general file set & needle file set-min. 5 sets, chisel set, hacksaw frame with sufficient blades-min. 5 sets, centre & hole punch set; letter & number punch set-min. 3 sets, tap set (6, 8, 10, 12 mm & ", 6", 1")-min, 4 sets each, flaring tool-min. 3 not, pointer puller-min. 3 nos, portable welding set with welding rods-min. 4 sets, hand lamp set (24 vdc)-min 5 sets, hand lamp set (240 vac)-min. 7 sets, power extension board with rccb-min. 7 nos, feeler gauge-min. 3 sets, thread gauge-min. 3 sets, ss tube benders (6, 8, 10, 12 mm)-min. 4 sets each, circlip plier (inner/outer)-min. 3 nos each, air blower-min. 4 nos, anti-spark spanner set & slide wrench (6", 8", 12")-min. i sets, spray painting machine-min. 3 sets, magnetic spanner-min. 2 sets2x660 mw unit # 4.
Tender For supply and installation of training items for drone technician trade under craftsman training scheme (cts) at consignee locations - pliers, soldering station, multi meter, binoculars, anemometer, magnifier, unassembled drone kit, unassembled drone kit - standard with hd camera & thermal camera, electricity lab, smd technology kit with wall chart, dc regulated variable programmable dc power supply, drone workbench, analog-digital circuits development platform, applied mechanics training platform, drone battery management training systems, charge controller training system, bldc (brushless dc) motor training system, inverted pendulum, drone sensor trainer kit, antenna training system, advanced microwave integrated circuit lab, gps training platform, wireless communication modules, fcb and esc training platform, drone gimbal set with motor and control, npnt compliant micro uav built for mapping and surveillance, field repair kits, drones and spare parts kit, balance charger, power distribution board, laptop latest configuration, thrust measurement meter, indoor netted facility, outdoor controlled netted testing facility, various electronic and electrical components, 3d printer, drone ( long range)
Tender For corrigendum : repair maint of old unsv meter panel meter box sub main wiring electric distribution board mccb mcb and other connected items under ge mis mhow