Tender For supply of r1 spares of ssl d d - water pump pully , indicator light , hyd temp sensor unit , bty cut off switch , baby filter , indicator switch , hours meter with cable , water temp gauge , oil temp gauge , fuel tank cap , lever knob
Tender For tender for supply of bearing set , cores for drier , power contactor , local/remote switch , lock nut , lock nut , lock nut , seal rod , ring retaining , ring retaining , lock washer , spring compression , plug orifice 3/8-18 nptf w/.277inch orifice 1918 , assembly shaft seal , rod indicator , spring unloader 1918 , assembly linear transmitter short stroke , valve slide 1918 , sleeve female distance , lock washer , fan bearing(fhy beraing d 25ukp 206-with adpter slee ve d25) , he d12 filter size 345x560 , elecrical actuator for motorised valve 100mm , control trafo ratio-480/120v(etf3010023) , flush type actuator red with element 2nc(epb1110013) , flush type actuator green with element 1no+1nc(epb2110013) , aux.contactor 4no(rl4rd040td) , pilot light assembly 24v dc with red led(elm1020058) , pilot light assembly 24v dc with green led(elm1020059) , pilot light assembly 24v dc with amber led(elm1020060) , ctrl trafo ratio-415/230v 200va(etf2110004) , impeller for swp , shaft along with sleeve for swp , impeller nut , bearing set for sw pump , mechanical seal for swp , shaft-impeller key cwp , coupling key for cwp , impeller nut for cwp , rubber bellow for ac plant sea water pump inlet , thermostatic expansion valve , differencial pressure gauge+switch for oil tag no.dpg101 , chilled water pressure transmitters tag no-01-pt-106 , lube oil temperature transmitter tag no.tt102 , pressure switch rt 1(lp) , pressure switch rt 5(lp) , liquid injection solenoid coil(18z6710) tag no.sv103 , level switch for oil model no.913a0123h01 tag no.ls 101 , valve , angle , sea water cooler se-6 , 3-way valve 15mm
Tender For corrigendum : supply of schedule iv (x-ray films, chemicals, e. c. g. rolls, materiels etc.) - schedule iv (x-ray films, chemicals, e. c. g. rolls, materiels etc.), polyster base round corner x-ray films (8" x 10") green sensitive, blue base with base fog less than or equal to 0.23 & dmax not less than 3.10 interleaved. the density values should be met at developer temperature 32 c to 35 c, polyster base round corner x-ray films (10" x 12") green sensitive, blue base with base fog less than or equal to 0.23 & dmax not less than 3.10 interleaved. the density values should be met at developer temperature 32 c to 35 c, polyster base round corner x-ray films (12" x 15") green sensitive, blue base with base fog less than or equal to 0.23 & dmax not less than 3.10 interleaved. the density values should be met at developer temperature 32 c to 35 c, dental x-ray films intraoral periapcal the density values should blue base with base fog less than or equal to 0.20 & dmax not less than 3.10 the density values should be met at developer temperature 32 c to 35 c, liquid developer replenisher for automatic processor (starter solution, if recommended by the manufacturer, should also be supplied), ( price of item no. 5 and item no. 6 will be considered as a unit), liquid fixer hardner for automatic processor ( price of item no. 5 and item no. 6 will be considered as a unit), inj. meglumine diatrizoate sodium diatrizoate iodine content 365-375 mg/ml in 20 ml. ampoule/vial, pigtail angiography catheter with multiple side holes length 65 to 75 cm 5f, inj. gadolinium based contrast for mri for liver/liver specific (should provide details of compound being hepatobiliary specific), inj. gadolinium based contrast for mri for general use, inj. gadolinium based contrast for mri for angiography, disp lure lock syringes 3 ml. for glue injection, disp lure lock syringes 1 ml. for glue injection, x-ray folders laminated 250 gsm 14 1/2" x 17 ", dual pack 200 ml syringe with aspirator, "y" shaped coiled tube y-tube sterile, non-pyrogenic (minimum 300 psi & above) compatible with dual head pressure injector ( lf/medrad/ sea crown / spectra / apollo), extension "y" shaped coiled tubing for injector 150 cms. (-5 or +15cm) low pressure (minimum 300 psi & above), dual disposable syringes (60 to 65 ml each) with "y" or "t"shaped coiled tube connecting tubes small spike for contrast and large spike for saline compatible with mri injector (lf or medrad)., one way stopcock (high pressure), low pressure extension "y" or "t" shaped coiled tubing min. 150cms (-5 or +15 cms) with coiled connecting tubes & small spike for contrast & large spike for saline for medical mri injector., flavoured, ionic, water soluble, oral contrast iodine content 240-250 mg/ ml. in 30 ml, bernstein catheter 4 f 100 cm, bernstein catheter 5 f 100 cm, chiba needle 21 g 15 cms length, chiba needle 22 g 15 cms length, disposable c t scan pressure injector syringes (190 ml syringe + quick fill tube) for bayer medrad salient injector (toshiba / canon), extension "y" shaped coild tube adapter dual check valves (minimum psi 300 & above), nonionic iodixanol isoosmolar, 320 mg 50 ml, disposable mri syringes kit for 65/115 mr injector system 65 ml contrast syringes and 115 ml ns syringes with connecting tubing combo pack for spectris solaris medrad pressure injector, spring loaded fully automatic and semi automatic biopsy instrument with adjustable penetration depth of 18 mm and 25 mm. having trocar tip with dimpling on needle and fire ready indicator. 14 g & 10 cm in length, spring loaded fully automatic and semi automatic biopsy instrument with adjustable penetration depth of 18 mm and 25 mm. having trocar tip with dimpling on needle and fire ready indicator. 16 g & 10 cm in length, coil shape breast tissue marker with both front trigger & an alternate rear trigger, should be visible in ultrasound, mammography and mri, extension coiled tube with integr