Tender For bid to ras corrigendum : tender for supply of supply of gas detectors : : - hydrocarbon gas detector , h2 detector , electrochemical type gas detector for o2 , so2 gas detector , fixed , detector , gas , h2s , chlorine gas detector , ammonia (nh3) gas detector , fixed co detector , eo detector , xguard-1 , is , 0 to 50ppm , crowcon , point type infrared hc gas detector t3 , hooter , gas alarm beacon , yellow , beacon blue for gas detector , chlorine gas leak detector w/sensor and acc , h2s gas detector , gas detector
Tender For requirement of spares of m/s ingersoll rand make conveying air compressor model r-160i-x 7.5wc and up5-22-7 for dry fly ash dense phase system,unit#3 and 4, ctpp, chhabra - model no. r160i-x7.5 wc, seal, shaft high pressure part no. 89292445, element, seprator tank 18 inch part no. 23566938/ 23545841, oil cooler, water cooled part no.23572415, after cooler, water-cooled part no.23572423, cap screw m6x25 soc hd cap w/nylon insert part no.22168710, pressure transducer 0-225 psig part no.47545275001, pressure transducer 0-15 psig part no.47560902001, assembly gear set 160 kw single stage 7.5 bar part no.23521859, pin dowel [motor] part no.39194915, pad pre filter part no.23523772, actuator service kit part no.23467251, inlet valve part no.23421217, elbow 1/4" 90 degree straight thread ms part no.96757604, spacer gear (ce177g) part no.39326483, sleeve motor shaft 4.25 od m132/160 part no.89292478, key,square both ends 0.88sq x1.25 part no.95135638, valve in line check part no.23453020, tube gear case scavenge part no.23453129, air cleaner assembly nlg37-42 pico standard part no.23390156, ultra coolant (208 litres) drum part no.39433743, key, rect one round end part no.96759212, clamp, plate part no.35295336, screw, socket head part no.32555819, housing, seal part no.22880744, gasket, gear case part no.39454558, pin, dowal [air end] part no.35295336, valve, orifice [separator tank] part no.23449200, oil filter assembly part no.23523434, o ring set part no.ok002222, pressure transducer cable part no.23529373, temprature sensor part no.23522246, valve min press check 132-160 kw part no.23521297, 5sv solinied cable part no.23562432, model no. up5-22-7, element coolant filter part no.54672654, element seprator 194cfm (spin-on) part no.54749247, pad pre filter part no.22053722, element air filter part no.89295976, kit, inlet valve repair part no.22067177, kit-mpcv part no.22064695, kit thermal valve repair part no.22393326/ 22832885, valve solenoid 125 inch npt part no.54774302, valve solenoid 1/2 in npt 110 volt part no.54654652, spring gas part no.54749114, elbow .31tx .50sae part no.95993572, elbow , 90deg male 37a10c3xz2 part no.95937686, tube oil feed (rear bearing) part no.85581858, tube, vmc block to bare part no.85581866, belt part no.89265052, ultra coolant (20litres) drum part no.38459582, tempreture sensor part no.22137848, conteroller part no.22128763, tube nylon part no.39124813, tube nylon part no.39124821, elbow part no.39155650, elbow part no.39155577, nipple part no.22354989
Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using
Tender For supply of roti making machine - heating coil, glass wire, sensor wire, plate set, pressing motor, pressing gear, temprature meter, contactor, ampere, votage indicator, indicator light, mc b 40 ,amp, baking motor, baking gear box, fan belt, black switch, capacitor, bearing, rotary switch, main gas pipr, 3 ft cu gas pipe, 1 ft cu gas pipe, gas valve
Tender For supply of w , carbon resistor 82 ohm,1 by 4w , carbon resistor 820e 1 by 4 w , carbon resistor3k9 1 by 4 w , ceramic capacitor 0 point 1ufd,630v , ceramic capacitor 100pfd , crocodile pin pair 16amp red and black , di soldering wick 2 point 5mm x 1 mtr long copper , diac db 3 ,3 point 3volt , diode 1n 4001 , diode 1n 4007 , diode 1n 5408 , electrolyte capacitor 10 micro farad 16v , electrolyte capacitor 100 micro farad 10v , electrolyte capacitor 1000 micro farad 16v , electrolyte capacitor 1000 micro farad 25v , electrolyte capacitor 1000 micro farad 50v , electrolyte capacitor 100mfd 25 v , electrolyte capacitor 10mfd 25 v , electrolyte capacitor 10microfarade,25 v , electrolyte capacitor 120-150 mfd, 440volt ac , electrolyte capacitor 2 point 2 microfarade,63 v , electrolyte capacitor 2 point 5 mfd, 230 volt is 1709 ac , electrolyte capacitor 22 mfd 25 v , electrolyte capacitor 2200micro farad 25v , electrolyte capacitor 330 mf,25 v , electrolyte capacitor 4 point 7 microfarade,25 v , electrolyte capacitor 470 micro farad 10v , electrolyte capacitor 470 microfarade,10 v , electrolyte capacitor 470mfd,25 v , electrolyte capacitor 47mfd,25 v , female to female jumper wires , fet , flame sensor , gang capacitor 135pf to 500pf , glass fuse 1amp , glass fuse 2amp , glass fuse 6amp , hook up wire, 1 coil equal to 90 mtr length , hrc fuse , ic 4017 , ic 555 , ic 7400 nand gate , ic 7402 nor gate , ic 7404 not gate , ic 7408 and gate , ic 741 , ic 7432 or gate , ic 7486 exor gate , ic 7805 , ic 7809 voltage regulator , ic 7812 , ic gf200850 12a , ic lm317 , ic socket 16pin , ic socket 8pin , igbt , inductor 100mh , inductor 3 point 3 millhenry 1amp , inductor 500mh , inductor 8h , ir sensor with pot , ldr , led blue 3v 5mm , led flexible strip , led green 3v 5mm , led lamp holder for 5mm led , led red 3v 5mm , led white 3v 5mm , led yellow 3v 5mm , lithium ion-li-ioncoin cell battery , main code wire 1meter 2 pin , main code wire 1meter 3 pin , male to female jumper wires , male to male jumper wires , metal diode, 25a , metal film resistor 100ohm zero point 25 to zero point 5 watt , metal film resistor 100ohm zero point 25 watt , metal film resistor 100ohm zero point 5 watt , metal film resistor 100ohm 1w , metal film resistor 10kohm zero point 25 to zero point 5 watt , metal film resistor 10mohm zero point 25 to zero point 5 watt , metal film resistor 10mohm zero point 5 watt , metal film resistor 1kohm zero point 25 to zero point 5 watt , metal film resistor 1mohm zero point 25 to zero point 5 watt , metal film resistor 1mohm zero point 5 watt , metal film resistor 22k 1 point 2 w , metal film resistor 22kohm zero point 25 to 1 watt , metal film resistor 22kohm zero point 5 watt , metal oxide film resistor 10m 5 w , metal rectifier 15 a , mica capacitor , mosfet irf540 15volt , mosfet irfz44 , mq 3 gas sensor , p.c.b. 4inch x 4inch , paper capacitor , pcb 6inch x 4inch , plastic film capacitor 0 point 0100 mfd , potentiometer 100k , potentiometer 10k , potentiometer 1m , potentiometers 1 k 1 w , potentiometers 100 ohm 1 by 2 w , potentiometers 250 k ohm 1 w , potentiometers 470 ohm1 by 2 w , preset 10k , resistor 100 ohm, 10 watt , resistor 10kohm , resistor 10m ohm, 5watt , resistor 1k 10w , resistor 1k ohm, 10watt , resistor 2.2k ohm, 2 watt , resistor 220 ohm, 2 watt , resistor 47 ohm , 1 by 2 watt , resistor 47 ohm, 5watt , resistor 470 ohm , 1 by 2 watt , resistor 560e , 1 by 4 watt , resistor 684 //bid details 2 / 142 ohm, 2 watt , resistors 10,20,30,40,50,60 ohm , 1watt , scr tyn 604 , soldering flux 50grm , soldering flux wire 500grm , soldering stick 60 colon 40 , soldering wire 80 colon 20 250grm equal to 1 no , sound sensor , switch dpdt 5amp , tantalum capacitor 6 ponit 8 mfd 35v , thermister ntc , thermister ptc , toggle switch dpst 5amp , toggle switch spdt 5amp , toggle switch spst 5amp , touch sensor , transistor 2n2222 , transistor 2n3906 , transistor bc 107 , transistor bc 108 , transistor bc 148 , transistor bc