Latest excavator loader Tenders | Government excavator loader Tenders

CTN :45720703

30 Jul, 2026 2.00 Crore

Chhatarpur - Madhya Pradesh

Tender For inviting rates of different items for construction of diffrent type of work as per demand on cm help line or ward parsad or public - supply of handpump material 2026-27, excavation for roadwork in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location with all lifts and lead up to 1000 m as per section-300 of the specifications.item no nvi-3.12, construction of embankment/sub-grade/earthen shoulders with material obtained from other sources, as per provisions of section 305 of the specifications, with approved materials/soil confirming to requirements given in table 301-1 of specifications including all lead and lifts, including cost of watering, compaction by vibratory roller/heavy pneumatic type roller etc. confirming to requirements given in table 301 2 of the specifications complete.item no nvi-3.12, construction of granular sub-base, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method at omc and compacting with vibratory roller of 80-100 kn static weight to achieve the desired density, including all lifts and lead complete in all respect as per section-400 of the specifications.by mix in place method item no nvi -4.1.1.1, construction of dry lean cement concrete sub- base over a prepared sub-grade with coarse and fine aggregate conforming to is: 383, the size of coarse aggregate not exceeding 26.5mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1 of the specifications, cement content not to be less than 150 kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 mpa at 7 days, mixed in a batching plant, transported to site, laid with paver with electronic sensor/mechanical paver, compacting with 8-10 tonnes vibratory roller, finishing and curing and as per section 601 of specifications.item no nvi- 6.1.1, providing and laying cement concrete grade m-20 with 20 mm graded crushed stone aggregate, mixing shall be in mechanical mixer, laying with paver compacting by use of pin, plate / screed vibrators including form work by strong steel girders fixed by spikes, separation membrane 125 micron thick, including cutting of joints @ 4 to 5 m interval and filling it with hot applied bituminous sealant (without dowel bars) (max. thickness 20 cm).item no nvi-6.4, construction of dowel jointed, plain cement concrete pavement in m-30 grade concrete over a prepared sub base with 43 or higher grade cement, coarse and fine aggregate conforming to is:383 maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver with electronic sensor spreading the concrete by shovels, rakes compacted using needle, screed and plate vibrator and finished in a continuous operation including provision of contraction, expansion, and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, placing of dowel bar, tie rod admixtures as approved, curing compound, finishing to lines and grades as per approved drawings as per irc:15 and as per section-602 of the specifications complete excluding cost of steel in dowel bar and tie rod etc.item no nvi-6.2.1, earth work in excavation for foundation, trenches for pipes / cables or drains etc. by mechanical means / manual means (exceeding 30cm in depth.) including ramming of bottom,dressing of sides,disposal of excavated earth including of all lift and lead upto 50m.disposed earth to be levelled and neatly dressed.all kinds of soil item no nii 2.6.1, demolishing cement concrete manually/by mechanical means including disposal of material with in 50 meters lead as per direction of engineer-in-charge.1:3:6 or richer mixitem no nii

State Government

CTN :45702997

30 Jun, 2026 NA

Ambala - Haryana

Tender For manhole chambers providing and fixing sfrc manhole covers and frames marked with is: 12592 including setting the same to correct lines and levels in 1:3 cement sand mortar over manhole including carriage loading unloading stacking handling re-handling etc. complete in all respects to the satisfaction to the engineer-in-charge. 1. type:- extra heavy duty set (ehd-35) 560mm clear opening , earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. all kinds of soil. ,demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2. nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix), cement concrete (cast in situ) providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work below plinth level and up to floor iv level: 6. 1:4:8 (1 cement : 4 coarse sand (zone-iii) : 8 graded stone aggregate 40 mm nominal size)

State Government

CTN :45704840

30 Jun, 2026 NA

Ambala - Haryana

Tender For providing gi pipes class b marked with is: 1239 in 3.05 m length, their threading and welding with flanges (heavy duty) on both sides, jointing with nuts and bolts ( w make), rubber gaskets , lowering into tube wells and testing including carriage, loading, unloading etc. complete in all respects to the satisfaction of engineer-in- charge. 3. 80 mm i/dq , providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 1. 80mm i/d cid joint ,providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 2. 100mm i/d cid joint , providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 3. 150mm i/d cid joint ,providing, lowering, laying in trenches, aligning, fixing in position and jointing ductile iron (di) isi marked k-9 grade sands pipes as per 15:8329-2000 (amended up to date), with internal cement mortar lining for potable water with rubber ring (epdm/sbr) joints as per is: 5382-1985 (excluding special accessories) complete including all material, labour, hydraulic testing and commissioning as per technical specifications and as per direction of engineer. note: e/w to be measured and paid separately ,earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. all kinds of soil. , demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2. nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix) ,providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work below plinth level and up to floor iv level: 2. 1:2:4 (1 cement : 2 coarse sand (zone-iii) : 4 graded stone aggregate 20 mm nominal size)

State Government

CTN :45704964

30 Jun, 2026 NA

Ambala - Haryana

Tender For cc interlocking paver blocks providing and laying 100mm thick factory made cement concrete interlocking paver block of m -35 grade made by block making machine with strong vibratory compaction, of approved size, design and shape, laid in required colour and pattern over (bis 15658:2006) and including 60mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of engineer-in-charge. ,providing, lowering, laying in trenches, aligning, fixing in position and jointing ductile iron (di) isi marked k-7 grade sands pipes as per is:8329-2000 (amended up to date), with internal cement mortar lining for potable water with rubber ring (epdm/sbr) joints as per is: 5382-1985 (excluding special accessories) complete including all material, labour, hydraulic testing and commissioning as per technical specifications and as per direction of engineer. , earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. all kinds of soil. ,demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2. nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix) , providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work below plinth level and up to floor iv level: 2. 1:2:4 (1 cement : 2 coarse sand (zone-iii) : 4 graded stone aggregate 20 mm nominal size)

State Government

CTN :45705821

30 Jun, 2026 NA

Sirsa - Haryana

Tender For providing, lowering, laying, cutting (cut surface to be uniformly finished), jointing with rubber rings marked with is : 5382 and testing of spigot and socketted rcc, np2 marked with is : 458-1988 and specials into trenches for all depths including carriage, loading, unloading, stacking, handling, re-handling etc. complete is all respects to the satisfaction to the engineer - in -charge. 4. 350 mm i/d ,`jointing plain and reinforced concrete pipes and specials of all classes in trenches using collar joints jointed with 1:1 cement sand mortar nearly dry heavily caulked into joints and with end dowels filled with 1:1 cement sand mortar including facing trowelling and finishing the joints at an angle of 45 degrees with faces of collars keeping joints wet till curved testing the drain lines for leakage and making good all leakage and defects as laid down in the contract specifications complete with two spigot ends jointed to collar and internal diameter of sewer pipe or special , earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer-in-charge. 1. all kinds of soil ,cement concrete (cast in situ) providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work below plinth level and up to floor iv level: 3. 1:2:4 (1 cement : 2 coarse sand (zone-iii) : 4 graded stone aggregate 40 mm nominal size),brick work brick work with common burnt clay non-modular bricks of class designation 10.5 in foundation and plinth in: 2. cement mortar 1:6 (1 cement : 6 coarse sand), cement plaster (in fine sand) 12 mm cement plaster of mix : 3. 1:4 (1 cement: 4 fine sand)

State Government

CTN :45702932

30 Jun, 2026 NA

Rohtak - Haryana

Tender For fixing bell mouths bailing out water from the trenches for making new connections in fully charged pipe-lines including cleaning trimming and dressing the trenches to correct alignment and grade as required by the engineer-in-charge. size of the main with which connection is to be made. 1. up to 200 mm internal diametre ,providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 2. 100mm i/d cid joint ,providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 3. 150mm i/d cid joint , earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer-in-charge. 1. all kinds of soil , demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2. nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix)

State Government

CTN :45702948

30 Jun, 2026 NA

Rohtak - Haryana

Tender For fixing bell mouths bailing out water from the trenches for making new connections in fully charged pipe-lines including cleaning trimming and dressing the trenches to correct alignment and grade as required by the engineer-in-charge. size of the main with which connection is to be made. 1. up to 200 mm internal diametre ,providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 2. 100mm i/d cid joint , providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 3. 150mm i/d cid joint , earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer-in-charge. 1. all kinds of soil ,demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2. nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix)

State Government

CTN :45702975

30 Jun, 2026 NA

Rohtak - Haryana

Tender For fixing bell mouths bailing out water from the trenches for making new connections in fully charged pipe-lines including cleaning trimming and dressing the trenches to correct alignment and grade as required by the engineer-in-charge. size of the main with which connection is to be made. 1. up to 200 mm internal diametre , providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 1. 80mm i/d cid joint , providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 2. 100mm i/d cid joint , providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 3. 150mm i/d cid joint , earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer-in-charge. 1. all kinds of soil ,demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2. nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix)

State Government

CTN :45702988

30 Jun, 2026 NA

Rohtak - Haryana

Tender For fixing bell mouths bailing out water from the trenches for making new connections in fully charged pipe-lines including cleaning trimming and dressing the trenches to correct alignment and grade as required by the engineer-in-charge. size of the main with which connection is to be made. 1. up to 200 mm internal diametre ,providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 2. 100mm i/d cid joint , providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 3. 150mm i/d cid joint,earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer-in-charge. 1. all kinds of soil, demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2. nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix)

State Government

CTN :45702989

30 Jun, 2026 NA

Rohtak - Haryana

Tender For fixing bell mouths bailing out water from the trenches for making new connections in fully charged pipe-lines including cleaning trimming and dressing the trenches to correct alignment and grade as required by the engineer-in-charge. size of the main with which connection is to be made. 1. up to 200 mm internal diametre ,providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 2. 100mm i/d cid joint , providing and fixing cast iron detachable joints class-15 marked with is: 8794 for use with asbestos cement pressure pipes complete with 2 nos. rubber rings marked with is:5382 and is:10292 and appropriate number of nut and bolts marked with is:1363 including carriage, loading, unloading etc. complete in all respects to the satisfaction of the engineer-in-charge. (excavation will be paid separately) 3. 150mm i/d cid joint,earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer-in-charge. 1. all kinds of soil, demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of engineer - in - charge. 2. nominal concrete 1:2:4 or leaner mix (i/c equivalent design mix)

Excavator Loader Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors