Latest face guard Tenders | Government face guard Tenders

State Government

CTN :45596388

23 Jun, 2026 NA

Delhi - Delhi

Tender For supply, installation, testing and commissioning of electrical and mechanical equipments for shallow bore tube wells phatak bans,sawar khan, chatta mom gran, lal darwaza in matia mahal constituency ac-21. - s/o submersible pump set fitted with dynamically balanced ep impeller mounted on stainless steel shaft protection sleeve ep stage bowl of closed grained shorted type impeller. the pump will be directly coupled to required wet type induction motor of speed 2900 rpm suitable for operation on three phase ac, 415 volts ,50hz, 5 hp, model no j46, head-70 mtrs, discharge-200 lpm. make:bs/ksb/crompton/djb approved, supply of automatic lt panel board suitable for 415 volts, 3 phase, 50 hz, 4 wire system for operation of up to 15 hp submersible set, made out of not less than 2 mm thick crca for load bearing members and 1.6 mm for doors of panel, totally enclosed, dust and vermin proof, floor mounted type. the panel size 760 mmx 1360 mm x300 mm and having (1) 63 amp change over- 1 no (2) 63 a tpn mccb -1 no (3) amp meter 0-50 a- 1 no (4) voltmeter 1 no (5) amp & volt meter selector switches-1 set (6) auto-manual + light + control mcb tp 32 amp- 1nos each (7) ct -3nos (8) push button + on/off light 2 nos each (9) 5 kvar shunt capacitor- 1 no (10) aluminium bus bar size 25 mm x 6 mm - 1set (11) 15 hp star delta starter (a) 32 amp power contactor-3 nos (b) overload relay 14-23 a -1 no (c) star delta timer- 1 no ( d) qt timer -24 hours -1 no (e) motor protection relay 200 short circuit, earth fault, phase loss, unbalance, phase reversal, locked rotor protection make:-subtec/protech/ l&t/all djb approved make, s/o pvc insulated flat submersible cable with copper conductor having three core size 2.5 sq mm 1100 volts(100mtr per roll). make- gloster/universal/havells/grandlay/djb approved, s/o g.i pipe 40mm dia medium class with threaded externally on both end socketed 6mtr long. make- jindal/tata., s/o g.i tail piece 40mm dia 600mm long medium class with threaded externally on both end. make- tata/jindal, s/o gi socket 40 mm dia with threaded internally. make: jindal/tata/djb approved, s/o gi elbow with both end having thread, size- 40mm. make: jindal/tata/djb approved, s/o gi reducer having thread on boyh end, size: 50mm to 40mm. make: jindal/tata/djb approved, s/o gi union having thread on both end, size: 40mm. make: jindal/tata/djb approved, s/o ms clamp of 600mm long 12mm thick complete with nut & bolts and washers for holding 40 mm dia pipe i/c bending & shaping etc., supply of ms bore cover 6 mm thick suitable for 100 mm dia casing in 2 pieces complete with bolting arrangement angle iron frame and provision of 40 mm dia hole in the center., supply of pvc suction hose pipe 50 mm dia 30 mtr long.make-jyoti/isi, installation of submersible pump set with pipe and other accessories, connection of cable, installation of electric panel, grouting of electric panel digging and fixing the same with the help of cc and laying of gi pipe from bore to panel executing minor civil making electrical connection with cable as required size i/c watch and ward cartage, taking all safety measures all tools and tackles. testing and commissioning of all e&m equipment on no load and full load conditions as per standard and full satisfaction of engineer-in- charge. this is a turnkey job and it further includes any left out items which may be required during execution of work will be firm responsibility & no extra payment will be paid. - s/o submersible pump set fitted with dynamically balanced ep impeller mounted on stainless steel shaft protection sleeve ep stage bowl of closed grained shorted type impeller. the pump will be directly coupled to required wet type induction motor of speed 2900 rpm suitable for operation on three phase ac, 415 volts ,50hz, 5 hp, model no j46, head-70 mtrs, discharge-200 lpm. make:bs/ksb/crompton/djb approved, supply of automatic lt panel board suitable for 415 volts, 3 phase, 50 hz, 4 wire system for opera

CTN :45398632

08 Jul, 2026 49.25 Lacs

Namchi - Sikkim

Tender For supply of various technical equipments for the outreach centre of indian himalayan centre for adventure and eco-tourism (ihcae), chemchey, namchi district. - vr headset experience station, vr headset (premium).(high-res, 120 fov, standalone), vr accessories kit.(straps, cleaners, face guards, cases), vr controllers.(hand controllers with haptic feedback), multi-device charging dock.(fast charging for 3 headsets simultaneously), vr content & experience software, everest vr experience.(360 immersive experience), software license (3 years).(multi-device licensing), physical replica & exhibition, 3d physical model.(scale model, terrain details), display case. (glass enclosure with lighting), signage & labels.(multilingual informational labels), interactive touchscreen stations, touchscreen display.(65" 4k uhd), interface software.(custom educational application), display stand.(stable base), electrical infrastructure, power distribution, lighting system, project management & logistics, project management, logistics & transport

State Government

CTN :45381292

08 Jun, 2026 38.05 Lacs

Nandyal - Andhra Pradesh

Tender For restoration & improvements to 12 nos. radial crest gates with hoisting equipment and 1 no. of 40 ton capacity gantry crane and 2 nos. service gates and 2 nos. of emergency gates of river sluice of n.s.r.s. srisailam project- 1" nylon rope , 1/2"nylon rope , 125a 4 pole mccb,25 ka (l&t) mat-02956 , 2 pole mcb as per field sample standard make , 20kg hyco high pressure pnuematic grease gun , 3" double layer paint brush , 4" double layer paint brush , 4mm welding electrodes , anker chain pulley block, for single grinder crane, capacity: 1 ton maximum lifting height 12m , bamboo ladder 10feet , bamboo ladder 12feet , bosch cutting wheel , broom sticks , cotton waste complete white , current transformer ct coils 5amps , electricians , fitter class -i , gi bolts/nuts and washers , helper , mechanic cl- i , operator spillway / sluice gate , over load relay 40a , paint removal iron scraper , power contactor make l&t mnx-70 , provision for rewinding and bearing of 30 hp and 25 hp electric motors including dismantling, rewinding of stator coils with suitable copper winding wire, insulation, varnishing, assembling, testing, commissioning, and providing necessary internal and external wiring. , provision towards labour charges for removal of honey bee hives which will exist at walk way bridge, hoist bridge,arm girders of r.c.gates etc., , pvc tapes , radial crust gates operating panel display model : conzerv dm3110 , red oxide iron primer paint gr.i , rotary level selector switch 2 ways on/off , synthetic enamel grade i paints ( various colours as per eng-in-chrg )(asian/berger)(block ,yellow) , tinnar oil , washing soaps , welder , wire brushes

CTN :45326589

09 Jun, 2026 NA

Tiruchirappalli - Tamil Nadu

Tender For supply of equipment items - dc motor:type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder: bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel supply: mounted on training base suitable for dismantling and inspection, hydraulic operated directional control valves (dcv):type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study, bearing with shaft assembly :type: dismantling and assembly teaching unit shaft diameter: 30 mm shaft material: en8 steel bearings: deep groove ball bearing (6205 / 6206) housing: cast iron locking arrangement: circlips lock nuts end covers mounting: bench-mounted / frame-mounted unit, coupling unit using driving and driven shafts using plummer block bearing unit :the plummer block housing material: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing). sealing: felt seals or v-ring seals (to demonstrate lubrication retention). lubrication: provided with a grease nipple at the top center for manual lubrication practice. the bearing type: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series). bore diameter: standard 25mm or 30 mm. shafting and coupling shaft material: ground carbon steel (en8 or en9) for high surface finish. coupling type: flexible coupling: to demonstrate the bearings ability to handle slight misalignment. rigid flange coupling: to demonstrate traditional direct connection. driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven).

State Government

CTN :45303639

06 Jun, 2026 NA

Ranchi - Jharkhand

Tender For e-quotation for seeking firm rates of plant and machinery and materials category items for preparation/amendment of schedule of rate for the year 2026. - m 1055 - pumps supplying submersible pump sets confirming to is 8034 and motor confirming to is 9283. pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/ noryl impeller. motor suitable for working on 415v+10%, 3ph, 50 hz, a.c. supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shall be suitable for direct coupling. pump shall have suitable outlet as per manufacturers design. anti thrust stream lined non return valve shall be provided with pump. 3 meter submersible copper conductor cable in single/ double run shall be provided with each pump., submersible pump set 100 mm dia (with polypropylene/ noryl impeller) up to 20 stages 1 h.p. , 1.5 hp, 2 hp, 2.5 hp, 3.0 hp, 4.0 hp, 5.0 hp, submersible pump 150 mm dia (with bronze/ss impeller) up to 8 stages, 1.5 hp, 2.0 hp, 3.0 hp, 4.0 hp, 5.0 hp, 6.0 hp, 7.5 hp, m 1056 - pressure guage providing fabricating, testing and commisioning pressure vessel fabricating in m.s plate on providing foundation including epoxy paint, pressure gauge (100 mm dia), pressure gauge (150 mm dia), vacuum / combination gauge, m 1057 - lifting equipment chain pulley block supplying triple spur gear type chain pulley block suitable for capacity as below with 3 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per is 3832 carrying isi mark., 1 tonne capacity, 2 tonne capacity, 3 tonne capacity, electric operated circular or rectangular travelling crane (single girder) supplying single girder electrically operated rectangular over head travelling crane with 6 m lift complete with wire rope hoist, class ii duty, all three motions electrically operated by suitable rating motor ip 54, control panel and down pendant control block., 5 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, 7.5 tonne capacity, above 6 m upto 8 m span, above 8 m up to 10 m span, 10 tonne capacity, above 6 m up to 8 m span, above 8 m up to 10 m span, m 1058 - lightening arrester, ab switch, insulators, lightening arrestor supplying, erecting approved make thyrite type lightening arrestor suitable for h.t. supply with necessary ancillary material complete on provided cross arm and connected to overhead line., suitable for 11 kv supply, distribution class, suitable for 22 kv supply, distribution class, suitable for 33 kv supply, station class, disc insulator. supplying, erecting porcelain disc type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, pin insulator supplying, erecting porcelain pin type insulators with hardware fittings suitable for h.t. overhead line complete erected with nuts and bolts on provided cross arm, suitable for 11kv line, suitable for 33kv line, air break switch without earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps, suitable for 11kv line, rocking / tilting type, rotating type, suitable for 33kv line, rocking / tilting type, rotating type, air break switch with earth switch supplying, erecting approved make h.t. outdoor type gang operated air break triple pole switch with earth switch of required capacity with 3 post / pin type insulator per phase , mounted in horizontal or vertical position on provided cross arm with adequate length of g.i. pipe for op

State Government

CTN :45228148

03 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For supply of tube cleaning equipment - heavy duty flexible shaft with antifriction lining complete with 5/8" inner core and, hand piece of plain end bearing type suitable for cleaning of 37 mm i.d, brass/ss tubes. (with outer casing not more than 33mm), length 25, length 30, heavy duty flexible shaft with antifriction lining complete with 1/2" inner core and, hand piece of plain end bearing type suitable for cleaning of 37 mm i.d brass/ss, tubes. (with outer casing not more than 33mm), length 25, length 30, spare hand pieces having plain end bearing for above flexible shafts (5/8mm inner, core) for cleaning of 37 mm id brass tubes, plain end bearing for above flexible shafts (5/8mm inner core) for cleaning of 37, mm id brass tubes, motor side nipples suitable for 5/8 inner core having female threads on one side, and 11/16 size on other side total length of nipple shall be 2, - do - but having female threads on one side (hand piece side), turk head brushes for cleaning of, 37 mm i.d. tubes, 37.6 mm i.d. tubes, 42 mm i.d. tubes, 98 mm i.d. tubes, 96 mm i.d. tubes, tool head cutter of 15 gears with male thread of suitable for cleaning of 37 mm i.d., tube cleaning motor of 5 hp x 2900 rpm, kirloskar make, duly mounted one trolley,, complete with dol starter, 2 mtr cable., steel wire dusting brushes of size 8 x 4 having steel wire protruding 1 x 16, swg, steel wire dusting brush of size 6 x 2 with handle having spring steel wire, protruding 1 x 16 swg with 5 rows of 14 bunches having 40 wires in each bunch., cleaning equipments eng.., flexible shaft with short hand piece (for bend tube)with 12 mm inner core and 10 mt, inner core flexible shaft 3/4", inner core of dia 5/8" for above flexible shaft, inner core of dia 1/2" for above flexible shaft, flexible shaft with short hand piece for bend tubes, 12mm inner core x 16 mtr long, flexible shaft with short hand piece for bend tubes, 18mm inner core x 12 mtr long, flexible shaft with short hand piece for bend tubes , 18mm inner core x 21 mtr long, tool head cutter complete for boiler bent tubes suitable for cleaning of tubes, of, (a) 76.2 mm od tube, (b) 70.0 mm od tube, (c) 63.5 mm od tube, (d) 50.0 mm od tube, cutter wheel for, (a) 76.2 mm od tube, (b) 63.5 mm od tube, (c) 70.0 mm od tube, (d) 50.0 mm od tube, trunk head brush suitable for boiler, 50 mm, 56mm, 63.5mm, 70 mm, 72.6 mm, 76.2 mm, pins for tool head cutters of above sizes (as per sample), plain end bearing for above flexible shafts, (spare hand piece having double ball bearing for flexible shaft 18mm inner core with, nipple 55mm long), plain end bearing for above flexible shafts, (spare hand piece having double ball bearing for flexible shaft 12mm inner core with, nipple 55mm long), hand piece side nipple with socket suitable for " inner core 2" length, m.s. nipple with socket suitable for " inner core, 10"x2" polymer wheel suitable for 50/100 kg sugar carying trolley, sugar bag carryaing trolly heavy duty quality heaving angular frame based on 2 nos, heavy duty polymer vheels size 10" by 2" shelf lubricated duly furnished and painted, load carryong 150 kg.

Central Government/Public Sector

CTN :44561166

10 Apr, 2026 NA

Bangalore - Karnataka

Tender For supply of procurement of exercise therapy and recovery physiotherapy tapes and strapping items c c - 15mm w x 3.0mm t , super loop band level 2 13mm w x 4.5mm t , super loop band level 3 21mm w x 4.5mm t , super loop band level 4 29mm w x 4.5mm t , super loop band level 5 44mm w x 4.5mm t , super loop band level 6 53mm w x 4.5mm t , super loop band level 7 63mm w x 4.5mm t , o-loopexercise tubing with velcro cuff , marker cones - set of 50 , 14 inch finger web exerciser assorted levels , 213cm length - floss band , flexi latex or silicone bar 12 inch and hand exercise latex bar assorted levels , fabric exercise loop band pink ultralight 32 cm x 6.4 cm , fabric exercise loop band yellow light 32 cm x 6.4 cm , fabric exercise loop band green medium 32 cm x 6.4 cm , fabric exercise loop band orange heavy 32 cm x 6.4 cm , fabric exercise loop band silver ultimate 32 cm x 6.4 cm , swiss ball 65cm , half balance ball and premium quality with grip texture in surface , togu challenge disc 2.0 , togu dyniar ballkissen 36cm , exercise tubing roll - 18 feet length - level 1 yellow , exercise tubing roll - 18 feet length - level 2 red , exercise tubing roll - 18 feet length - level 3 green , exercise tubing roll - 18 feet length - level 4 blue , exercise tubing roll - 18 feet length - level 5 black , exercise tubing roll - 18 feet length - level 6 silver , exercise tubing roll - 18 feet length - level 7 purple , high density exercise mat 10 mm with eyelet holes and carry strap , folding high density exercise mat 5mm , ankle weight with neoprene material 0.5kg , ankle weight with neoprene material 1.0kg , ankle weight with neoprene material 1.5kg , ankle weight with neoprene material 2.0kg , ankle weight with neoprene material 3.0kg , slam ball with grip texture- 3 kg , slam ball with grip texture- 5 kg , slam ball with grip texture- 8 kg , slam ball with grip texture- 12 kg , pilates ball 25cm , soft weight ball 1.0kg - rehab , soft weight ball 2.0kg - rehab , vibra pole - long , body suspensions trainer with adjustable straps , calf and ankle stretcher , hand exercise putty 100 gms , reaction ball - large , non woven disposable sheet , neutral massage cream for long massage 1000 ml with ce marking , neutral massage oil 1000 ml with ce marking , neutral massage cream and basic 550ml without ce marking , rigid orthotic insole for flat feet with raised arch - 5 sizes , cold gel menthol based 150 ml with ce marking , cold gel menthol based 500 ml with pump with ce marking , cold spray 220 ml menthol based with ce marking , cold spray 90 ml mentha pipperita 4gm , physio on field bag medium 16 inch x 9.5 inch x 9 inch multi pocket adjustable partition , physio waist kit pouch 6.5 inch x 11 inch x 2.5 inch with inner separators , thermoplastic splint sheet and perforated 46cm x 61cm x 2.4mm , skin on skin hydro gel 1 inch x 1 inch and 200 squares in a jar , 15cm fabrica gel tubes open end pack of 4 sizes and set of 4 sizes , silicone heel cup 3 sizes , rigid height elevator wedge 6mm , rigid height elevator wedge 8mm , economical massage table wooden 3 section , economical massage table aluminium 2 section , aluminium massage table super lightweight 2 section less than 11 kg , premium flexi wrap for ice bag and universal velcro style , 6.5cm fabrica gel toe caps pack of 4 sizes with set of 4 sizes , accupuncture needles with guide tube 0.20mm x 13mm , accupuncture needles with guide tube 0.30mm x 75mm , economical cupping set and 12 cups , economical cupping set and 24 cups , premium quality cupping set with gisha tool and 12 cups , premium quality cupping set with gisha tool and 24 cups , premium quality cupping set and 19 cups , hot and cold gel pack , kinesioogy taping scissors - platinum with black //bid details 2 / 149 handle with non stick blades , bag with wheels for carrying a massage bed , rigid transparent face guard for nasal fractures , sport shield roll on for protection against chafing 45ml , mulligan belt , ez-wrap with handle ,

Face Guard Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

State Government

Central Government/Public Sector