Tender For supply of vacuum contactor 400 amps 3.3kv part no. ht200 , vacuum contactor closing coil 110v dc part no. ht203 , vacuum contactor holding coil 110v dc part no. ht204 , p. t. 40va part no. ht206 , auxiliary contactor part no. ht208 , resin cast pt 300va 3.3kv by 110v 3 phase part no. 350 or ht350 , e.l.unit complete without transformer part no. 800 or ht800 , power hrc fuse part no. ht1500 , brass cable gland complete with c.i clamp stud part no. 1600 or ht1600 , static type relay part no. ht900a , pilot relay 12dc part no. ht2200 , contactor part no. ht200a , diode by255 for vacuum contactor part no. ht200c , vacuum contactor rectifier bridge part no. ht201 , copper terminal bar part no. 701 or ht701 , terminal chamber for i by c t by g o by g and partition part no. 1600b or ht1600b , auxiliary switch for vacuum contactor 2no and 2nc part no. ht205 , resin cast part no. ht300 , ht control fuse 3.3kv 2amps part no. ht400 , resin cast moulded cbct part no. ht500 , resin cast part no. ht650 , dmc moulded 3.3kv insulator for power fuse part no. ht700 , hrc fuse base and carrier for control part no. ht1200 , hrc fuse part no. ht1201 , lamp holder part no. ht1400 , cable box complete w o gland for i by c t by g oby g and partition part no. 1600a or ht1600a , isolator handle on off with axel bush part no. 1501 or ht1501 , copper bus bar 400 amps set of 3 part no. ht101 , relay part no. ht900e , isolator limit switch part no. ht1700 , isolator part no. ht100b , 72 sq mm ammeter suppressed scale part no. 1000 or ht1000 , ammeter selector switch part no. 1001 or ht1001 , single phase preventer cup 20 part no. 2001 or ht2001 , 72 sq mm voltmeter 0 to 5 kv by 110 volt part no. 1100 or ht1100 , resin cast part no. ht600 , push button with element for start stop test and reset part no. 1300 or ht1300 //bid details 2 / 29
Tender For supply of wiper blade front 600 driver m s bcs , wiper blade co dvr , switch assy combination , spg brake chamber repair kit msp5 1 , assy release cable comp centre flap , spring brake actuator w adoptor type , motor assy starting , linkage , plug oil drain , filter ass oil , blade assy wiper , belt water pump
Tender For supply of single mode 04 core ofc , single mode 12 core ofc , hdpe pipe 40 mm , optical fxo_fxs 16 port 4e1 and ethernet up to 80 km , optical fxo_fxs 08 port 4e1 and ethernet up to 80 km , l-2 switch manageable 24 port , 12 f fibre termination box , 4 f fibre termination box , pig tail 10 mtr with fclc connector , splicing and joint enclouser , ups 4 kva , brick chamber , cable warning tape , 2 inch gi pipe with road crossing , route marker , digging laying and trenching of ofc with road crossing
Tender For corrigendum : supply of phaco emulsification system , ultrasound , vitrectomy , diathermy , phaco hand pieces , phaco tips , phaco sleeve , hand piece test chamber , phaco cassettes or tubing sets , i a hand piece bimanual or coaxial , vitrectomy cutter 23ga or 25ga , diathermy forcep and cable , online ups 3 kva , reusable phaco cassettes or tubing sets
Tender For special repair / replacement of lt panel, lt cable, tpn / spn dbs, voltage stabilizer, bus bar chamber, earthing and connected accessories installed at transit camp under ge 865 ews
Tender For quotation for rate of c/f pump (clear water) and its accessories at saraswatipur rwss - supplying ,installation and commissioning of multi stage/ horizontal split casing/multi stage centrifugal pump (make: kirloskar / wpil/jyoti/ mather & platt) rating-15 kw/20hp as per is:5120, capable for discharging 72 m3/hr against a head of 40 m , consisting of bronze impellers, stainless steel pump shaft, etc. with all accessories coupled with energy efficient (ie3) tefc squirrel cage induction motor confirming to is:325 and is:12615, having 15% more bhp than that of pump, operating on 1500rpm, 415v, 3 ph, 50 hz [make: kirloskar /abb/cgl/bhel] all complete with required size of sluice valve and cidf non- return valve standard fitting, strainers, reducer, foot valve, pressure gauge, nuts & bolts, packings, fitting & fixing, labour & technician, etc. all complete job as per site requirement and direction of e/i. discharging -72 m3/hr and head - 40m (1w + 1s) 20 hp, cost towards making new foundation base for pump -motor set and panel including providing new ms base plate as per sample suitable for 20 hp pump- motor set, cutting and welding where necessary, nuts, bolts, flange etc with all labour, tools and materials all complete job., cost towards making suitable suction line by suppling of ms pipe, bend, flange, nut, bolt rubber insertion, including making hole for suction, cutting, welding etc all complete., cost towards making suitable delivery line by suppling of ms pipe, bend, flange, nut, bolt rubber insertion including joining the new suction line to the existing header by means of cutting, welding etc all complete., providing , erecting and commissioning lt motor control panel board fabricated with ms sheet and painted, dust-vermin proof. floor mounted cubical panel board shall be consisting of proper power distribution 100 a copper busbar- 4 pole, 1 no. 100 a mccb as incoming feeder and 2 nos. 63a mccb as outgoing feeders for motors, 1 no. 63 a mccb as spare feeder (for motor), 2 no. 32a mcb for lighting and other loads. including selector switches, switch disconnector isolator, voltmeters, ampere meters, mfm, indicator lamps, internal wiring, danger board, protection units & relay, capacitor banks/apfc and 02 nos suitable fasd starter, etc. all complete and as per is and direction of e/i .), supplying and erecting 16 sqmm 3 core xlpe / pvc insulated, 1100 v grade un-armoured copper cable with isi mark stranded / solid copper conductor complete erected on wall / panel or in provided trench in an approved manner. (from panel to motors), providing and erecting chemical earthing with all required materials etc all complete., cost of 3t triple type chain pully block suitable as below with 6m lift complete with laoad chain and hand chain suitable for avove lift, tested 50% over load as per is 3832 carry isi etc. all complete job as per the site requirement and indian standard., cost towards dismanteling of old pump set and foundation and making arrangements for removal of debries from the pump house., construction of chamber for 100mm sluices valve.