Get complete information related to latest Firing Pin Spring Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Firing Pin Spring Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Firing Pin Spring Tenders.
Tender For auction sale of depot non ferrous scrap - brass lump scrap - 98200045(15) cond.& u/s brass lump scrap consisting of flow lamp, oxygen regulators, 63a 5 pin plug components, spcc panel components, catenary ending cones, catenary splices, bushes, bolts, nuts, gas cutting torches, gm valves, float valves, tap bib cock, cp angle valves, dropper clips, contact wire swivel clips, marut hand compression sprayer, brush holders, terminal connectors, pg clamps, bracket direct clamps, steel wire ending cones, briddle wire dopper clips, rods, key spindle, nozzle type, dv components, trunnion body for bmbc, etc. available in the bin with or without other attachments. total gross weight: 865.6 kgs. said to contain total brass content: 845.501 kgs approx., total ms content: 5.65 kgs approx, total aluminium content: 5.194 kgs approx, total stainless-steel content: 3.14 kgs approx, and plastic, rubber, etc: 6.115 kgs approx. hsn code:74040022; gst@18% on forward charge basis. note: 1) delivery on actual weighment basis only 2) segregation not permitted. 3) purchasers/firms are requested to physically inspect the lot before offering their bids. 4) post auction no representation shall be entertained.5) it is the responsibility of the purchaser/bidder to return excess material, if found during gross weighment, to the nominated premises of the custodian. 6) request for fixation of delivery point should be invariably raised in ireps online only. purchasers are requested to make use of this facility. 7) railways does not guarantee for quality, quantity description etc. location: non-ferrous ward bin no: 1.
Tender For procurement of spares of pa fan igv assembly for 2x250 mw units at paras tps on open tender basis during aoh of unit-3. - blr pa 0 0 stud m16x1.5 d22, l: 180, blr pa 0 0 swivel pin d25;l: 110, blr pa 0 0 swivel pin d25, l135, blr pa 0 0 inner spindle assy, blr pa 0 0 dry bush mb 4050 du, blr pa 0 0 blade assy of igv, blr pa 0 0 outer spindle d50, l: 160
Tender For corrigendum : supply of power steering system of american crane model 5450 t spare parts as per catalogue f f - power steering assembly part number 197461 , ring snap 7g32726 , ring snap 7g32417 , ring snap 7g32727 , dw seal 7g3266615 , washer 7g36524nf , head 7g36522 , o- ring seal 7g32077 , rod piston , seal rod 7g32131 , piston ring set 7g406 , piston 7g34614 , nut 7g32464 , cylinder body , pin 7g407 , block 7g408 , lubrication fitting 7g32013 , repair kit 7g2897 , wheel hub 110120 , air brake chamber 222227 , air brake chamber 814583 , boom dog air valve 807472 , swivel joint assembly l4802 , planet spider assembly 114449
Tender For supply of liner cylinder std , seal o ring liner , bush cam shaft , bearing crank shaft 0 10 , bearing connecting rod 0 20 , piston with pin with lock , piston ring std , thrust washer upper std , thrust washer lower std , bush connecting rod u b , rod and cap assy connecting rod with bolt and nut , pin dowel block , engine overhauling gasket set complete , valve air intake , valve exhaust , seal valve stem , valve seat , valve guide , seal oil crank shaft rear , seal o ring spacer , seal oil crank shaft front , bolt fan , bearing fly wheel , belt drive fan belt , filter assembly secondary for turbo charger , filter assy engine oil , tap and screen assy fuel fuel tank , disc clutch pto , disc clutch main , kit fuel filter primary and secondary , gasket oil sump , gasket fip ear inspection plate , gasket water pump , gasket crank shaft rear oil seal , gasket timing gear housing , gasket timing gear cover , gasket cylinder head , gasket cylinder head cover , gasket air intake manifold , filter assy hydraulic lift oil intake , seal o ring hydraulic , clamp radiator upper , seal o ring , seal benjo washer , u j cross propeller shaft , yoke propeller shaft , bush pin swivel housing upper front axle , bearing sp herical lower , pin swivel housing upper wing pin post , seal o ring front axle , seal oil half axle shaft 4wd front axle , seal wheel housing 4wd front axle , tie rod end , cylinder assy power steering pipe inner and outer , clamp assy house , gasket water outlet , ring thermostat sealing , gasket exhaust manifold , hose assy fuel filter to fip pump , hose assy fuel feed pump to fuel filter , gasket hydraulic pump , hydraulic oil filter , gasket turbo charger oil outlet , pipe metal power steering to inter oil , pipe metal hydraulic pump , jubilee clip half inch , benjo washer copper all size , benjo bolt 19 no , benjo bolt 17 no , bolt and nut 10 no , bolt and nut 12 no , bolt and nut 14 no , valve grinding stick , seal oil gear box , gasket egr valve , injector fuel return pipe rubber , gasket fuel tank , gasket turbo charger to adopter , stopper cable , temperature sending unit , oil pressure sending unit , front indicator sparking light assy , back light assy , insulation tape , 0 to 20 no size writing brush short hair , 0 to 20 no size writing brush long hair //bid details 2 / 64
Tender For supply of mig/mag welding torch 5 metre length conforming to specn - iec 60974-7 orequivalent standard of make tbi/esab/ abicor binzel/nutecsys .2. size of wire: 0.8 - 1.2mm3. current rating: 350 amps @ 60% duty cycle (10 minutes cycle) for co2. 300 amps @ 60%duty cycle (10 minutes cycle) for mixed gas.4. type of end connection: euro connector5. triggering pin in end connection: movable spring loaded6. shielding gas: argon/co2/argo shield.7. type of cooling: gas cooled/air cooled.8. triggering switch: mechanical/electrical type.9. swan neck angle and type: 45 degree to 60 degree bend -changeable swivel neck.10.torch cable: ribbed coaxial cable.11.connection at torch end: knuckle jointfor easy maneuvering12.weight: light weight torch (weight not to exceed 4.5 kgs for torch with 5m length cable). [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]
Tender For supply of contact wire swivel clip complete set (with pin) as per rdso drg. no. re/33/p/1220 (rev-e) conforming to specification no. ti/spc/ohe/fitting/0130 (10/13) (rev-1) [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variationpermitted: max 8 lacs ] ]