Latest flashlights Tenders | Government flashlights Tenders

corporations/Associations/Others

CTN :45702242

07 Jul, 2026 17.03 Lacs

Kota - Rajasthan

Tender For regular operation and maintenance of street lights (with material) at all industrial areas under riico ranpur kota(for 2 years) - regular operation and maintenance of high mast light in ranpur , kota including supply and replacing the required material and labour etc. complete as per the following terms and conditions:- i at any moment a minimum of 90% of total fixture must be in order. the defective fixture must be repaired within 3 days, falling which deduction for number of light which are not functioning in the industrial area shall be made at one time of the rate (accordingly deduction for lights which are not functioning becomes two times of the rates from total payment due for total number of lights whose operation and maintenance was awarded to the contractor ). ii contractor shall arrange at his cost for put on & off the street light fixture at appropriate time regularly as per instructions of engineer-in charge. a register shall be maintained at riico/association office and complaint lodged must be attended by contractor within 24 hours. the person deputed by contractor shall attend the riico/association office daily and comply the instructions and attend complaints regularly. iii contractor will have to employ trained and qualified electricians for the work. iv corporation shall not be responsible for any kind of accident during execution of work. v contractor will be responsible for safety and security of fixtures and all concerned materials. vi contractor will be responsible for arrangement of all t&p required for the work vii cost of all labour and material like lamp / balllast wire etc. will be born by contractor. all material required for the work shall not be below the category-ii of concerned bsr item. contractor has to repair and maintenance of fixture with material in all cases like short circuit, phase to phase of jvvnl line etc. viii no extra payment will be made for fixing/removal of extra/existing fixture in the industrial area. ix contractor will be responsible for timely collection and deposition of electric bills of areas in each month. in case of delay in payment and jvvnl impose surcharge for delay payment the same will be recovered from the running bill fo the contractor. payment of electricity bill will be made by riico. x contractor will be responsible for rebate of timer provided by jvvnl. hence contractor will maintain the on/off system by timer properly. in case no rebate is provided by jvvnl due to failure of timer then rebate will be deducted from contractor payment. xi contractor will be responsible for any theft of electricity through poles and he will make necessary arrangements for this. in case of any theft is found suitable penalty will be imposed on the contractor. xii contractor will maintain cubical panel board and assessories fitted in it. in case of any fault repair/replace of material will be done by the contractor at his own cost. no extra payment will be made on behalf of material. xiii contractor has to keep ready total fixtures. in case of fault of fixture a penalty of rs.100/- per fixture per day will be imposed on the contractor., regular operation and maintenance of street light fixtures hpsv/ hpmv (70w/150w) in ranpur, kota including supply and replacing the required material and labour etc. complete as per the following terms and conditions:- i at any moment a minimum of 90% of total fixture must be in order. the defective fixture must be repaired within 3 days, falling which deduction for number of light which are not functioning in the industrial area shall be made at one time of the rate (accordingly deduction for lights which are not functioning becomes two times of the rates from total payment due for total number of lights whose operation and maintenance was awarded to the contractor ). ii contractor shall arrange at his cost for put on & off the street light fixture at appropriate time regularly as per instructions of engineer-in charge. a register sh

Corporations And Associations And Others

CTN :45723486

08 Jul, 2026 5.01 Lacs

Delhi - Delhi

Tender For procurement of material and hiring of labour for day to day maintenance of various electrical installations in municipal parks and buildings in ward 140 inderpuri under kbz - supply of 1.5 sq. mm isi marked, frls pvc insulated,single core copper conductor cable as required., supply of 4.0 sq. mm isi marked, fr pvc insulated, single core copper conductor cable as required., supply of 63 amps., 2 pole isolator as required., supply of 6 a, to 32 a, ratings, dp mcb, "c" curve, 10 ka breaking capacity as required., supply of 6a to 32 a ratings, sp mcb, "c" curve, 10 ka breaking capacity as required., supply and fixing of 32mm dia x 1 meter long g.i. pipe (medium class) bracket for mounting of fluorescent/hpmv/hpsv street light fitting on pole including bending the pipe to the required shape , 2 nos 25mm x 6mm flat iron clamps with nuts, bolts and washer , painting the flat iron with primer and finish paint etc. as reqd., supply of xlpe insulated pvc sheathed al. conductor un-armoured cable 1.1kv grade conforming to is-7098 of following size:- 2x 6 sqmm, supply of xlpe insulated pvc sheathed al. conductor armoured cable 1.1kv grade conforming to is-7098 of following size:-2c*10 sqmm, supplying, lowering, testing and commissioning of vertical type, multistage, totally enclosed water filled deep well submersible pumping set complete i/c connection etc. as reqd. (c) three phase 5.0 hp having discharge of 300 lpm approx. at 39 m head., providing following labour for day to day maintenance of ward i/c required t&p etc. in one shift in a day on all working days (required maintenance material will be provided by department) as required as per terms & condition of the department (excluding parts) complete as required. 1. skilled labour", providing following labour for day to day maintenance of ward i/c required t&p etc. in one shift in a day on all working days (required maintenance material will be provided by department) as required as per terms & condition of the department (excluding parts) complete as required. 1. un-skilled labour", supply of led street light fixture, powder coated pressure die cast aluminium body (system lumen efficacy 120 135 lm/watt) of following body materials. - 45 watt

Corporations And Associations And Others

CTN :45523190

19 Jun, 2026 4.76 Lacs

Delhi - Delhi

Tender For provision of new led street lights with allied accessories on existing poles at various dark spots in saidulajab ward no 160 under south zone - led street light fixture, powder coated pressure die cast aluminium body (system lumen efficacy >135 lm/watt). supplying, installation, testing & commissioning of street light led fixture, powder coated pressure die cast aluminium body with built in or separate driver as per the requirement with driver efficiency >85%, input voltage: 140-270 volt ac, frequency 50/60 hz, operating temp range -5 0c to 50 0c, internal surge protection of 5 kv l,n,e as per iec 61000-4-5, driver efficiency >85%,thd 10% as per iec 61000-3-2, p. f. 0.95, ip-66,ik-10, cri >70, under voltage and over voltage protection, emi-emc as per cispr-15, lenses for beam angle as per iesna type i/ii/iii as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (led,driver & electrical circuitary) of minimum 50000 burning hours with 70% of initial lumen maintained till life ends as per lm80 extrapolation ies tm-21-11 report, cct 3000 k / 4000 k / 5700 k /6500 k (as per ansi bin), sdcm(standard deviation color matching)5, maximum power consumption should not more than the specified rating and fixture shallbe of relevant bis standard complete in all respect i/c external connections with 1.5 sq mm frls/hffr, pvc insulated copper conductorsingle core cable and earthing etc. as required withminimum 5 year oem warranty. system lumen efficacy >135 lm/watt output . lm79 & lm80 testreport and all testing required for led fixturesas per bis shall be submitted.. shape size and cct shall be as approved by engineer-in-charge asper requirement. (thermal management: heat sink of aluminium housing such that led junction temperature shall not rise above 90 c). 45 watt , supply and fixing of 32mm dia x 1 meter long g.i. pipe (medium class) bracket for mounting of fluorescent/hpmv/hpsv street light fitting on pole including bending the pipe to the required shape , 2 nos 25mm x 6mm flat iron clamps with nuts, bolts and washer , painting the flat iron with primer and finish paint etc. as reqd, supplying and drawing following sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required. 3 x 1.5 sq. mm, supply of xlpe insulated pvc sheathed al. conductor un-armoured cable 1.1kv grade conforming to is-7098 of following size:-2c*4 sqmm, laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size in the existing masonry open duct as required. upto 35 sq. mm

Corporations And Associations And Others

CTN :45523194

19 Jun, 2026 4.67 Lacs

Delhi - Delhi

Tender For provision of led light fittings with accessories at various locations in ward no. 167 khanpur, under south zone. - supplying and drawing following sizes of frls pvc insulated copper conductor, single core cable in the existing surface/ recessed steel/ pvc conduit as required. 3 x 1.5 sq. mm, supply and fixing of 32mm dia x 1 meter long g.i. pipe (medium class) bracket for mounting of fluorescent/hpmv/hpsv street light fitting on pole including bending the pipe to the required shape , 2 nos 25mm x 6mm flat iron clamps with nuts, bolts and washer , painting the flat iron with primer and finish paint etc. as reqd., supply of xlpe insulated pvc sheathed al. conductor un-armoured cable 1.1kv grade conforming to is-7098 of following size:-2c*4 sqmm, laying of one number pvc insulated and pvc sheathed / xlpe power cable of 1.1 kv grade of following size in the existing masonry open duct as required. upto 35 sq. mm, led street light fixture, powder coated pressure die cast aluminum body (system lumen efficacy 135 lm/watt) supplying, installation, testing & commissioning of street light led fixture, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with driver efficiency >85%, input voltage: 140-270 volt ac, freq 50/60 hz, operating temp range -5 deg centigrade to 50 deg centigrade, internal surge protection of 5 kv l,n,e as per iec 61000-45, driver efficiency >85%,thd 10% as per iec 61000-3-2 , p. f. 0.95, ip66,ik-10, cri 70 , under voltage and over voltage protection,emi-emc as per cispr-15, lenses for beam angle as per iesna type i/ii/iii as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (led,driver & electrical circuitry) of minimum 50000 burning hours with 70% of initial lumen maintained till life ends as per lm80 extrapolation ies tm-21-11 report , cct 3000 k / 4000 k / 5700 k /6500 k (as per ansi bin) , sdcm(standard deviation color matching) 5, maximum power consumption should not more than the specified rating and fixture shall be of relevant bis standard complete in all respect i/c external connections with 1.5 sq mm frls/hffr, pvc insulated copper conductor single core cable and earthing etc. as required with minimum 5 year oem warranty. system lumen efficacy 135 lm/watt output . lm79 & lm80 test report and all testing required for led fixtures as per bis shall be submitted. shape size and cct shall be as approved by engineer-in-charge as per requirement. (thermal management: heat sink of aluminum housing such that led junction temperature shall not rise above 90 c). 45 watt

CTN :45453446

29 Jun, 2026 NA

Multi City - Multi State

Tender For supply of imalent ms32 or similar flashlight - 200,000 lumens, rechargeable flashlights of high lumens, led- cree xhp70.2 leds powerful flashlight with oled display,8 modes, handle, pd 100w type-c fast charging. detailed specification attached in document section. make/brand- imalent- ms32 orequivalent. [ warranty period: 30 months after the date of delivery ] ]

CTN :45159066

11 Jun, 2026 33.89 Lacs

Guna - Madhya Pradesh

Tender For supply of electrical materials for the repair and maintenance of street light as per the boq - details, t-5 power/energy saver 2x24w choke, t-5 power/energy saver 24w ftl tuberod, 2x24 t5-holder, t5 power saver 2x24 fixture acrylic transparent cover, t5 power saver 4x24 fixture acrylic transparent cover, 150w hpsv choke, 150w hpsv lamp, capacitor 33mfd 250vac 50 hz, electronic ignitor suitable for 150w hpsv lamps, 150w holder (porcelain), led driver 50w bis certified, led mcpcb plate 60w, led mcpcb plate 50w, led mcpcb plate 150w, supplyingof isi marked and approved make of moulded case circuit breaker(mccb) suitable for 3phase,3pole,50hz,415 volts, ac supply with respective interrupting capacity(ka) at 415 volts cited against their range standard conforming to is - 8828: 8.1mccb with breaking capacity 25 ka at 415 v: current rating -125 amps & 70% -100% adjustable, supply of sovp device should have single high capacity varistor in the l-n plug and encapsulated spark gap for n-pe, l-n sovp should have a rated voltage of minimum 320v ac to handle indian power supply conditions. sovp should have visual indication on replaceable varistor and spark gap modules as well as a potential free contact on the socket for remote indication. sovp device should be wired up as per tt configuration of wiring in accordance with en 61643-11 standards. both the l-n and n-pe, spds should be rated for handling 30ka of nominal 8/20 s surge current.: sovp for pole light sub feeder panels - type 2 pluggable spd 3+1, rating l-n/n-pe uc 255/320 v in 30/60ka ka, lmax 30ka/60 ka, up 1.5kv, supplying of isi marked and accepted standard of miniature circuit breaker(mcb)ofcseries suitable for 240/415volts,50cycle,10ka value ac supply confirming to is:8828:1996,iec:60898 :2002 but without enclosures: single pole 63 amp., astronomical timer with dst feature, contactor 3 pole 90 amp 50hz 415volts with no-nc contacts, tpn connector 150a, supply of approved make powder coated sheet steel encloser spn mcb db inclusive of busbar,neutral bar,earth bar & two earth terminals etc. complete as per is:13032 (exclusive of mcb & isolator): 8 way double door, supply of sovp device should have single high capacity varistor in the l-n plug and encapsulated spark gap for n-pe, l-n sovp should have a rated voltage of minimum 320v ac to handle indian power supply conditions. sovp should have visual indication on replaceable varistor and spark gap modules as well as a potential free contact on the socket for remote indication. sovp device should be wired up as per tt configuration of wiring in accordance with en 61643-11 standards. both the l-n and n-pe, spds should be rated for handling 30ka of nominal 8/20 s surge current.: sovp for pole light - type 2 pluggable spd 1+1, rating l-n/n- pe uc 230/400 v in 5 ka, imax 10 ka, up 1.2kv, led batten tubelight 20w, supplying of approved make tpn mcbdb metal double door with provision for fpmcb/isolator/rccb/rcbo as incomer and sp mcbs as outgoing inclusive of busbar,neutral bar,earth bar & two earth terminals etc. complete as per is:13032 (exclusive of mcb & isolator ): 8 way (8+24), 8 sq.mm multistrand pvc insulated copper wire bundle 90mtr, 1.sq.mm aluminium single core wire bundle of 100mtr. isi marked, xlpe insulated power cable( conforming is-7098 part-1) 1100 volt grade 2-core isi marked with alu. stranded/solid conductor: 16 sq.mm unarmoured, xlpe insulated power cable( conforming is-7098 part-1) 1100 volt grade 4-core isi marked with alu. stranded/solid conductor: 16 sq.mm unarmoured, xlpe insulated power cable( conforming is-7098 part-1) 1100 volt grade 1-core isi marked with alu. stranded/solid conductor: 25sq.mm unarmoured, wooden ladder 21ft, toolkit set consisting of different sizes l-keys, screw drivers, testers and plier set., taperoll box consisting of 30pcs (conforms to is: 7809 (part 3, sec 1),self extinguishing,protects from electrolytic corrosion,excellent water resistance,suitable for primary ins

corporations/Associations/Others

CTN :45246695

02 Jun, 2026 NA

Panaji - Goa

Tender For ghrssidc/e-t/2026-27/646 - electrical fabrication - a, la cross arm clamp for 7.5 mt rcc pole (gal v) - cee/e/523, sa cross arm clamp for 7.5 mt rcc pole (gal v) - gec/e/523, la cross arm clamp for 9 mt rcc pole (gal v) - gec/e/524, sa cross arm clamp for 9 mt rcc pole (gal v) - gec/e/524, la cross arm clamp for 105 lbs/yd rail pole (gal) - gec/e/723, sa cross arm clamp for 105 lbs/yd rail pole (gal) - gec/e/723, la cross arm clamp for 60 lbs/yd rail pole (gal) - cee/e/486, sa cross arm clamp for 60 lbs/yd rail pole (gal) - cee/e/486, la cross arm clamp for 90 lbs/yd rail pole (gal) - cee/e/515, sa cross arm clamp for 90 lbs/yd rail pole (gal) - cee/e/515, la stay clamp for 60 lbs/yd rail pole (gal) - cee/e/469, sa stay clamp for 60 lbs/yd rail pole (gal) - cee e 469, la stay clamp for 90 lbs/yd rail pole (gal) - cee/e/508, sa stay clamp for 90 lbs/yd rail pole (gal) - cee/e/508, la stay clamp for 7.5 mtrs rcc pole galvanised - cee e 523, sa stay clamp for 7.5 mtrs rcc pole galvanised - cee e 523, la stay clamp for 105 lbs/yd rail pole (gal) - cee e 723, sa stay clamp for 105 lbs/yd rail pole (gal) - cee e 723, la stay clamp for 9 mtrs rcc pole (gal v) - cee e 524, sa stay clamp for 9 mtrs rcc pole (gal v) - cee e 524, 11 kv v shaped cross arm (gal v) - cee e 408, 33 kv v shaped cross arm (gal v) - cee e 408, b type modified distribution box - cee e 386, a type street light meter box with clamps - cee e 386, stay set for 11 kv lt line - cee e 500, stay set for 33 kv line - cee e 500, turn buckle& eye bolt for 33 kv line - cee e 513, turn buckle& eye bolt for 11 kv line -cee e 466, cast iron packing piece 90 lb for rail pole - cee e 514, top insulators fitting for rcc pole - cee e 506, 4 pin angle type cross arm - cee e 702, 4 pin channel type cross arm - cee e703, 2 pin angle type cross arm - cee e704, 2 pin channel type cross arm - cee e 705, earthing pipe - cee e 467, sa cross arm clamp for ht/lt line on 11 mt rcc pole made of 50 x 10 flat (g) - cee e 711, la cross arm clamp for ht/lt line on 11 mt rcc pole made of 50 x 10 flat (g) - cee e 711, sa stay clamp for ht/lt line on 11 mt rcc pole made of 50 x 10 flat (g) - cee e 711, la stay clamp for ht/lt line on 11 mt rcc pole made of 50 x 10 flat (g) - cee e 711, sa bottom clamps for fixing street light fixtures for 7.5/9mtrs rcc pole galvanised 25 mm pipe - cee e 12, sa top bottom clamps for fixing street light fixtures for 7.5 mts rcc pole galvanised 25 mm pipe - cee e 12, la top clamps for fixing street light fixtures for 7.5/9 mts rcc pole (gal v) 40 mm pipe - cee e 612a, sa top clamps for fixing street light fixtures for 7.5 rcc pole - cee e 612a, gi nut and bolts in various sizes electro galvanised, gi pins for lt pin insulator, gi pins for 11kv pin insulator, gi pins for 33kv pin insulator, gi bent pipe of nominal base 25 mm, 1 mts long for tube light fixture - cee/e 618, gi bent pipe of nominal base 25 mm, 1.5 mts long for hpsv lamps - cee/e 593a, b type modified distribution box with mccb and kit kat fuses as per cees specifications / drawings, metal parts for shackle insulators as per cees specifications, gi bent pipe of nominal base bar 40mm x 3 mts long (medium class) the pipe shaft should conform to is : 1239 (part i) 1973 as amended upto date - ee/ii/21/2009, hot dip galvanised earthing strips of size 30x160x5mm, hot dip galvanised earthing strips of size 100 x 360 x 3mm, g.i bent pipe nominal bore 40 mm ce/e xi for hpsv lamps - cee/e 593a, metal parts for disc insulator as per department 4 bolted. as per department specification & drawing - 60/4/va/cee/tech/2019-20/1282, metal parts for disc insulator 3 bolted - 60/4/va/cee/tech/2019-20/1282, kit kat fuse 100 amps, kit kat fuse 200 amps, kit kat fuses 300 amps, kit kat fuse 400 amps, tinned copper fuse wire of various sizes, aluminium crimping lugs 25 sq.mm, aluminium crimping lugs 35 sq.mm, aluminium crimping lugs 50 sq.mm, aluminium crimping lugs 70 sq.mm, aluminium crimping lugs 95 sq.mm, aluminiu

CTN :45267753

01 Jun, 2026 NA

Ranchi - Jharkhand

Tender For supply of flashlight having 200,000 lumens, rechargeable flashlights of high lumens, led- cree xhp70.2 leds powerful flashlight with oled display,8 modes, handle, pd 100wtype-c fast charging. make/model - imalent ms32 or similar [ warranty period: 30 months after the date of delivery ] ]

Central Government And Public Sector

CTN :45034299

27 May, 2026 NA

Kaiga - Karnataka

Tender For corrigendum : supply of sfsb sfib under water fixtures d d - 1. under water lighting fixture -400w, 240v, 50 hz hpsv flood light , 2. lamp holder - spares for model no. sk 59 lighting fixture , 3. glass cover - spares for model no. sk 59 lighting fixture , 4. o ring - spares for model no. sk 59 lighting fixture , 5. protection cover - spares for model no. sk 59 lighting fixture , 6. cable leading tube - spares for model no. sk 59 lighting fixture , 7. gaskets - spares for model no. sk 59 lighting fixture , 8. ignitor super imposed for 1000w mh lamp. spares for superkino model no. sk 52-3 lighting fixture , 9. p.f. improvement capacitor - spares for model no. sk 52-3 lighting fixture , 10. under water lighting fixture, 1000w 240v, 50 hz hpmh all round circular flood light , 11. o ring - spares for model no. sk 52-3 , 12. protection cover- spares for model no. sk 52-3 , 13. ballast spare for model no. sk 52-3 mh lighting fixture , 14. 1000 watt metal halide lamp suitable for model no. sk 52-3 lighting fixture , 15. cable leading tube spare suitable for model no. sk 52-3 lighting fixture , 16. 400 watt ballast suitable for sk 59 lighting fixture , 17. ignitor suitable for sk 59 lighting fixture , 18. 400 watt hpmh lamp suitable for model no. sk 59 lighting fixture , 19. lamp holder - spares for model no. sk 52-3 lighting fixture

CTN :44975434

07 May, 2026 45.9 Thousand

Multi City - Karnataka

Tender For supply of hns items to district hospital ballari - bio medical waste trolley 25 ltr 3 bin-color redgreenyellow, capacity25 litre, frame stainless steel, bins material plastic, usage/application hospital, structure foot pedal , bio medical waste trolley 30 ltr 4 bin-color red green yellow, capacity 30 litre frame stainless steel, bins material plastic usage/application hospital, structure foot peda, bio medical waste bin -for hospital, capacity 50 litre, material-hdpe, structure-foot pedal,red/yellow/blue/ green/black, heavy duty., white gold quality paper glass disposable for for hot and cold beverages (urine cups) 1x500, stainless steel locks-6 livers, stainless steel locks-7 livers big sige, sodium hypochlorite solution sanitizing disinfect (1x5 l), mysore half bar soap-1x250 gms , plastic double hockey shaped toilet brush -for daily cleaning washroom, toilet, bathroom, medium size cell battery, bleaching powder 1x1 kg, washing powder blue 1x100 gms, cobweb brush with telescopic rod-extendable broom featuring long stainless steel handle,product dimensions 31.2l x 7.8w x 70.2h centimet, carbolic soap-1x125 gms, heavy duty rechargeable flash light super bright 1w led light brightness with the 1w led, provide a powerful white light. , coconut stick brooms -70 cm overall length- large-best quality, natural coir solid brown rectangular door mat rug quickdry with anti slip rubber backing for indoor size 2x4 feet, colin or equivalent glass cleaner- 1x500 ml, cotton thread no.10, dettol germ protection handwash liquid soap-1x 180 ml or equivalent, dish wash powder-1x1 kg, three bucket mop winger trolley system for hospital cleaning 3 bucket mop wringer trolley (60 ltr), door mat-4 x 10 feet anti-slip waterproof pvc cushion wire mesh rectangular , dry cotton pad floor mop- wet and dry cotton floor mop with 5 feet long handle with 360 degree movement with 1 extra cotton pad refill (head 24-inch large) , dry cotton pad floor mop- 18-inch head , plastic dustpad/supdi-supadi, standard size with best quality, glucometer batteries-should have long battery life, type lithium coin cell battery voltage 3 volts, capacity 225 mah or more, liquid vapourizer mosquito repellent machine set, liquid vapourizer mosquito repellent liquid, harpic toilet cleaner -regular liquid toilet cleaner 1x5 l, handwash liquid soap refill-germ protection,1x5l, measuring tape-durable soft 1.50 meter 150 cm , naphthalene ball/moth fragrance balls-with pure quality- 1x100 gms, white), natural grass floor broom -should have garo-hill grass , super strong & durable, mechanical locking, ergonomic handle broomstick, eco-friendly, bristle material-grass, battery 1.5 volts pencil cell-size aaa, voltage 1.50 v, material zinc carbon (remote cells small), transparent rectangular plastic box-shape- rectangle, pattern-plain, length-12 inch, height-04 inch, width-8 inch, material thickness-4mm, plastic bucket-standard quality, 25 litre capacity, without lid & with steel handle, plastic water barrel storage drum/container- 200 liters, including cap making charges., plastic mug1 ltr-special feature-break resistant, plastic stationary tray- multi, standard rectangular-weight upto 450 to 500 gms, 42 cm x 30 cm x 9 cm, cylindrical plastic pedal dustbin,capacity 10 l, structure foot pedal,spare part lid, bio-medical waste handling plastic covers-52+ microns as per cpcb guidelines, non-chlorinated, size-30x60 inches, labelled with warming symbol of bio-hazard & cyto-toxic, categories pritned as per colour code-red, green, blue & yellow 1x1 kg, rat glue pad-non-poisonous pad with a solid adhesive to trap pesky rats, carbon zinc battery - heavy duty, 1.5 volts, remotes, flashlights, clocks, toys etc, size-aa, detergent bar-1x250 g, disposable shaving razor & blade set, rubber slippers- color white, weight-100 gms minimum, seze no-8,9, & 10 in pairs, dual clip mop-100% pure cotton, stainless steel handle, floor cleaning mop set (white), dual clip mop refil-100% pure

Flashlights Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Corporations And Associations And Others

Corporations And Associations And Others

Corporations And Associations And Others

corporations/Associations/Others

Central Government And Public Sector