Get complete information related to latest Flyover Repair Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Flyover Repair Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Flyover Repair Tenders.
Tender For purchase of tanche - lab equipments for eee and ece department - purchase - lab equipments for eee department electronics lab, single phase to single phase cyclo converter kit single-phase bridge cycloconverter power devices: scr/triac based input supply: 230 v ac, 50 hz step-down isolation transformer 230 v / 12 v output: 12 15 v ac, frequency: 0 25 hz (adjustable),firing angle control circuit and frequency control circuit to be provided built-in resistive load, terminals to be brought on ms panel with necessary symbols and circuits, pwm based step down dc chopper using mosfet/igbt kitpwm based step-down dc chopper (buck converter) power device : power mosfet / igbt based switching circuit input supply : 24 v dc to 110 v dc or derived from 230 v ac mains through rectifier unit output voltage :(0 to vin) variable dc output current : up to 5 a dc maximum with suitable load resistor (r load) pwm duty cycle control provided pwm generation and control circuit inbuilt gate driver circuit provided, single phase single pulse / sinusoidal pwm inverter using mosfet/igbt kittype : single phase pwm inverter trainer power device : mosfet / igbt based inverter circuit input supply : 12 24 v dc output voltage : 30 v rms ac output phase : single phase output frequency : 0 50 hz variable output power : 100 w single pulse pwm operation sinusoidal pwm (spwm) operation variable frequency control pwm generation and firing control circuit inbuilt gate driver circuit provided test points provided for waveform observation and analysis built-in resistive load provision, on / off control of lamp using solid state relay kittype : solid state relay (ssr) trainer kit control/input voltage : 12 v / 24 v dc or up to 30 v dc output load voltage : 230 v ac, single phase load control : on/off control of ac lamp load solid state relay based switching circuit opto-isolated input control built-in ac lamp load manual on/off switching arrangement led indication for input and output status, speed control of ac motor using vfd drive module with ac motortype : variable frequency drive (vfd) module input supply : 415 v ac, three phase, 50 hz output : three phase variable voltage and variable frequency ac output 1 hpthree phase squirrel cage induction motor415 v ac 50 hz &1440 rpm control technique : pwm / spwm based control frequency range : 0 50 hz variable digital display for frequency and operating parameters start / stop and forward / reverse control, acceleration and deceleration control facility powder coated ms control panel tabletop / floor mounted laboratory type setup clearly labelled circuit diagram and control switches proper insulated terminals and earthing arrangement, purchase - lab equipments for eee department electrical machines lab, three phase transformertype: three phase transformer, rating: 3 kva input voltage: 415 v ac, 3-phase, output voltage: 230 v ac, 3-phase frequency: 50 hz winding material: copper wound insulation class: class b or higher duty: continuous duty suitable for laboratory usebench/floor, dc stepper motor drive kit with stepper motorinput supply : 230 v ac, 50 hz stepper motor : permanent magnet / hybrid type with suitable driver circuits. motor operating voltage : 12 24 v dc variable speed control forward and reverse direction control full step and half step operation manual / automatic pulse generation facility built-in regulated dc power supply led indication for phase sequence and status test points provided for waveform observation start / stop control switches to be provided overload and short circuit protection to be provided mounted on compact powder coated cabinet with printed circuit diagram proper insulated terminals and interconnecting leads to be provided patch chords for interconnection., dc servo motor drive kit with servo motorinput supply : 230 v ac, 50 hz servo motor type : dc servo motor with feedback arrangement motor operating voltage : 12 24 v dc controller type : microcontroller based servo drive contr
Tender For bid to ras supply of arduino uno microcontroller , breadboard , jumper wires male female , resistors , led red green , capacitors , transistors , diodes , sensors , lcd , relay module , motors , power supply battery , multimeter , soldering kit , project work station , fpga trainer boards , logic analyzer , dual regulated power supply , arduino uno , stm dev board , pic development kit , raspberry pi , digital multimeter , dac trainer board , rtos trainer , soldering stations , lm analog temp sensor , ds digital temp sensor , ptrtd resistance temp detector , k type thermocouple , ir proximity sensor reflective ir , digital ir obstacle sensor , ir flame sensor , ir temperature sensor mlx90614 , mq two lpg smoke , mq three alcohol , mq six lpg butane , mq seven carbon monoxide , mq air quality , pir motion sensor , ultrasonic sensor , accelerometer , gyroscope , solderless breadboard full size , mini breadboard , jumper wires male male , jumper wires male female , jumper wires female female , ic socket eight pin , ic socket fourteen pin , ic socket sixteen pin , solar cell trainer kit , ujt as relaxation oscillator kit , scr characteristics kit , ldr , photo diode , phototransistor , semiconductor temperature coefficient trainer kit , logic gate trainer kit , ic trainer kit , measurement of steady state and transient response of rl rc and rlc circuits , frequency response of twin t notch filter and to study of active filter , study of single phase inverter trainer , to study the behaviour , determine the transient , to study of pid controller for simullatio n process , to study basic electric al trainer , to study single phase transformer , to obtain efficiency of a dc shunt machine , to obtain efficiency and voltage regulation of a single phase transform , to study dc series motor , make connection of dol starter , test the machines required , maxwells bridge trainer kit ) /bid number : gem/2026/b/7582907 * /dated: 27-05-2026 & & / bid document 1 / 44
Tender For single range moving coil dc portable voltmeter , single range moving iron ac or dc portable voltmeter , digital multimeter , analog multimeter , digital logic trainer , wheatstone bridge portable , construct a circuit to measure ac voltage by voltage divider method , lvdt trainer kit , thermistor characteristic apparatus , speed measurement module using magnetic sensor , dc regulated power supply single channel , cathode ray osciloscope
Tender For supply of spares for 100kn servo electric utms - limit switch for kappa 100ss-cf, p/n z108.057, limit switch for hydraulic adjustment, p/n z108.078, remote control for setting up inching operation, p/n mp02489, usc module kappa, universal measurement amplifier, for connecting resistive and inductive bridge sensors, choice of ac/dc power supply, 4 and 6-conductor technology, 24-bit calculated resolution, module occupies one module bus slot, p/n mp00525, insulation end disc half, ultiform uvs 144, p/n z551.004-014, heating element kanthal apm, id 5 in, length 4in, fur 1250 °c p/n z906.072, furnace insulation vertical plate, p/n z551.004-010, furnace thermocouple type s for 5" furnace incl. compensating cables, p/n z551.034, solid state relais 30a/660v for ht-controller 1200°c p/n 930.ssm1a130bd, moving iron instrument 0...5a/10a, p/n 930.eq48, power supply 24 v, p/n 930.2868635, contactor tesys 7.5 kw, p/n 930.lc1d18bl, extension cable hiperface for tcii, p/n 977.066342, external power supply 48v/10a, p/n z240.054-011
Tender For purchase of lab equipments for ece dept - purchase of lab equipments for ece dept, dc voltmeter (digital) (item code : c006) 1.dcvoltmeteranalog moving coil -(0-10)v, class1.0( 1%full- scale)accuracy - 5 nos2.dcvoltmeteranalog- movingcoil-(0-30)v, class1.0( 1%full-scale)accuracy - 4nos, dc ammeter(item code : c007)specifications: 1. dcammeteranalog movingcoil- (0-30)ma,. 5 nos2. dcammeteranalog -movingcoil -(0-1000) a, class 1.0 ( 1 % full-scale) accuracy - 5 nos, decade capacitance box(item code : c0011)specifications: range: 100 pf to 100 f rotary switch selection with 6 dials. maximum voltage: 350 v. accuracy: 1%., decade inductance box(item code : c0012specifications: range:10 hto10h. rotaryswitchselectionwith6dials. low-lossinductors. accuracy: 1%., 8051 microcontroller kit(item code : c0013)specifications: operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc2148) (item code : c0014)specifications: cpu - lpc2148, core - 16/32 bit arm7tdmi-s speed - max 60 mhz, flash - 512kb, ram (on chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converter with 14 analog inputs, one 10bit d/a converter, six pwm & watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay & buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, temperature measurement kit (item code : c0019)specifications: sensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc). display: 3 digit led/lcd digital display (typically 200 mv fsd). temperature source: portable water kettle or heater block. signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation. test points: multiple 2 mm / 4 mm banana sockets for monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntc thermistor probe, k-type thermocouple probe, patch cords and user manual., fpga trainer kit(item code : c0025)specifications: must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb uart bridge, usb cable. user manual.
Tender For purchase of equipments ( s.no 1 to s.no 5 ) for ece department - purchase of equipments, dso (digital storage oscilloscope) bandwidth: 50 100 mhz. sampling rate: 1 gs/s. channels: 2 (minimum). power supply: 100 240 v ac, 50 60 hz. automatic measurements: vpp, vavg, vrms, frequency, period, vmax, vmin, rise time, fall time, +width, width, +duty, duty, etc. horizontal scale: 5 ns/div 50 s/div or equivalent. vertical resolution: 8 bits (2 channelssimultaneously). vertical sensitivity: 1 mv/div 10 v/div (at input). waveform math: +, , , , invert, fft, etc. waveform storage: 16 waveforms or equivalent. communication interface: usb host and usb interface. display: 7-inch color display or equivalent. input impedance: 1 m 2% || 20 pf. accessories: 2 passive probes (1x/10x), 8051 micro controller kit operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc 2148) cpu - lpc2148, core - 16/32 bit arm7tdmi-s speed - max 60 mhz, flash - 512kb, ram (on-chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converter with 14 analog inputs, one 10bit d/a converter, six pwm & watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay& buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, strain guage trainer kit ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual., sim reader trainer kitpower supply: operates on 230 v ac 10%, 50 hz mains supply. built-in regulated smps power supply. operating dc supply: 5 v / 12 v with overload and short-circuit protection. sim card interface: supports gsm sim cards compatible with 2g /3g / 4g / 5g networks. sim card read/write interface. supports sim card initialization, authentication,and communication functions. compatible with standard 6-pin / 8-pin sim cardsockets.communication interface: usb 2.0 interface for pc communication. rs-232 serial communication interface. uart communication facility for embeddedsystem interfacing. sim operating parameters: selectable sim clock frequencies: 3.579 mhz 7.159 mhz 14.318 mhz sim supply voltage selection facility. sim reset and activation control.supported protocols and standards: gsm etsi 07.07 and etsi 07.05 at commandsupport. iso/iec 7816 smart card communication support. sim communication command monitoring facility.hardware features: on-board sim card socket. led indication for: power status sim detection reset activity data transmission/reception built-in keypad for standalone operation. lcd display module (128 64) for menu andstatus display. on-board microcontroller-bas
Tender For corrigendum : supply of encoder module ei7 b drn100 , encoder module ei7 b dr71 , encoder module ei7 b dr112 132 drn112 , bridge rectifier bge 1 5 , terminal board w4720 ktm4 4 08 as kb , terminal board w4720 ktm5 as m5 , terminal board w4720 ktm4 4 12 as kb , inclined belt motor p drn90l4 be2 fg without gearbox , oil seal din a30x47x7 nbr , oil seal din a35x52x7 nbr , oil seal w as30x62x7 nbr , oil seal w basf30x52x6 nbr , oil seal w as30x55x7 nbr , oil seal w basf40x90x10 nbr , oil seal w basf85x140x12 nbr , oil seal w baofsf18x35x6 7 nbr , oil seal w as45x75x8 nbr , oil seal w as35x62x7 nbr , oil seal w basf50x80x10 nbr , oil seal w a17x30x7 nbr , oil seal din a20x35x7 nbr , hollow shaft ka47 fa47 sa57 d35 , hollow shaft ka37 fa37 sa47 d30 , accessory bag r13 r43 r76 ktm4
Tender For supply of igbt (insulated gate bipolar transistor) is a three-terminal semiconductor device (gate,collector, emitter) that combines the high-speed switching of a mosfet with the low saturation voltage of abipolar junction transistor (bjt). specifications: (1) model no:ff1400r17ip4 (2) voltage : 1700 v (3) current :1400 a (4) repetitive peak collector current : 2800 a (5) collector-emitter saturation voltage : 1.75 v to 2.2v @ 1400a, 15v (6) gate-emitter peak voltage :20 v (7) module type: half-bridge (dual switch). (8) operating temperature: -40 to 150 ?c. (9) internal gate resistor: 1.6 ohm. (10) series/package: prime pac 3.make: infineon, mitsubishi, semikron, abb. [ warranty period: 12 months after the date of delivery ]