Latest fuel gauge Tenders | Government fuel gauge Tenders

Central Government/Public Sector

CTN :45737258

10 Aug, 2026 NA

Jhansi - Uttar Pradesh

Tender For supply of glass tube (fuel gauge) as per drg.no. emd part no.8245707 [ warranty period: 30 months after the date of delivery ] ]

CTN :45633019

03 Jul, 2026 20.0 Thousand

Darjeeling - West Bengal

Tender For corrigendum : supply of oil filter , fuel filter , fan belt , air filter , fuel gauge , coupling pad , engine packing kit

CTN :45739518

10 Jul, 2026 1.58 Lacs

Siang - Arunachal Pradesh

Tender For supply of brake shoe assembly , brake wheel cylinder , wheel cylinder assembly , pto shift cylinder assembly , shift cylinder body high , ac compressor condenser , 4x4 prop shaft assembly , fuel gauge unit , windscreen glass , air pipe , cabin shock absorber , spider bearing , transfer case oil seal assembly , clutch plate set , front wheel bearing assembly , air filter , 4x4 sensor , rear lever kit , drive shaft hub nut , abs sensor , injector * /bid number : gem/2026/b/7723679 + /dated: 29-06-2026 ' ' / bid document 1 / 19

CTN :45711090

03 Jul, 2026 NA

Parganas - West Bengal

Tender For spare parts of scania - connector 1/4" part no 140523, oil collector part no 257319, hand brake valve part no 249914, switch, foot dipper part no 159656, stop light switch part no 158717, t-connector part no 229020, air dryer part no 258985, charging valve part no 215619, elbow connector part no 146235, elbow connector part no 229704, pressure regul. valve part no 5360042991(230787), safety valve part no 293542, valve seat part no 229358, repair kit part no 263664, repair kit part no 263667, bumper part no 249727, stop part no 217280, contact holder part no 235650, sliding contact part no 130770, cap lower part part no 1102372, cap upper part part no 1102371, oil container part no 197804, hydraulic oil pump part no 259310, relay part no 371912, comp circuit part no 259240, relay part no 173554, block terminal part no 353489, socket part no 255080, starting socket part no 231631, battery main switch part no 197811, gear selector (gear box) part no 6695000734(393779), gear selector (transfer box) part no 5895022571(393777), tandom driving cable part no 1149732, bulb 2w/24v part no 258491, panel, switches part no 248821, panel, control lamps part no 248820, map reading lamp part no 218412, control lamp oil pressure part no 239170, control lamp full beam part no 239173, light filter part no 246680, control lamp (direct indicator i) part no 239174, control lamp (gear box oil temp) part no 255073, control lamp coolant temp part no 246856, control lamp (reversing light) part no 249300, plate, blackout lighting part no 391567, techometer part no 258660, comb instrument part no 268353, oil pressure gauge part no 259794, water temp gauge part no 249108, fuel gauge part no 249109

CTN :45698399

08 Jul, 2026 NA

Varanasi - Uttar Pradesh

Tender For corrigendum : supply of fuel gauge asm (this is a safety item) as per drg.no. 8383728 alt ea as per specn. specification for cleaning,marking and packing , misc-437 [ warranty period: 30 months after the date of delivery ]]

CTN :45716137

09 Jul, 2026 NA

Mysore - Karnataka

Tender For fuel gauge float to part no. 131429004000

CTN :45416078

13 Jul, 2026 NA

Cuttack - Odisha

Tender For corrigendum : supply installation and commissioning of mechanical equipment for different govt itis and polytechnics of odisha - lathe s.s &s.c. (all geared type) , solid works , universal milling machine , powersaw machine , pipe bending machine , tool and cutter grinder , pillar type drilling machine , double ended pedestal grinder , air compressor , surface plate - granite , battery operated pallet truck , cylindrical grinding machine , radial drilling machine , absorption and stripping , equipment , shearing machine , surface grinding machine , hyadraulic surface grinding , machine , hand drill machine , horizontal milling machine , demarcation equipment , universal cylindrical grinding , machine , gear pump test rig , battery operated order picker , sensitive bench drill machine , shaping machine , hydraulic pressure testing , machine , plotter , vertical milling machine , power hacksaw machine , co-ordinate measuring machine , screw pump , breaker machine , battery operated fork lift , band saw machine , hdpe butt fusion welding machine , portable drilling machine , horizontal milling machine , turret ram milling machine , silicon carbide grinder , profile projector , slip gauge as johnson metric , set , vertical milling machine , slotter machine , hydraulic pipe bending machine , electric pressure , test pump machine

CTN :45583387

01 Jul, 2026 NA

Jodhpur - Rajasthan

Tender For bid to ras supply of lv7 tata 2651-5420-9932 fuel gauge , lv7 stln vf x- 7423500 assy of fuel filter 1.1 ltr , lv7 stln vf p- j100013 solenoid switch assy , lv7 stln 2530-018129 parts kit power steering , lv7 tata 8854-1501-2516 kit starter motor consisting of , lv7 stln vf 6130- 72-0464271 rectifier metallic

CTN :45715936

10 Jul, 2026 NA

Patiala - Punjab

Tender For supply of lv7 mg mounting engine front , lv7 tmb 2724-2520-0144 assy clutch disc 330 dia , lv7 tmb 2763-2500-0101 assy clutch disc pressure plate , lv7 tmb 2573-2520-0108 assy 310 dia clutch disc , lv7 stln b-3942303 air dryer assy , lv7 mg 11360m71c00 cover timing belt inside , lv7 t-815 452-335-871-506 becon orange , lv7 t-815 137-613-254- 080 steering lock , lv7 t-815 443-815-432-020 circuit breaker , lv7 mg 33400m78l00 coil assy ignition , lv7 t- 815 130-079-650-014 fuel gauge float , lv7 t-815 319- 232-099-0 piston ring , lv7 stln vf 14683760174 ar distributor head , lv7 t-815 443-319-032-000 horn valve

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

Fuel Gauge Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector