Latest fuel pump motor Tenders | Government fuel pump motor Tenders

Central Government / Public Sector

CTN :45319843

04 Jun, 2026 NA

Vadodara - Gujarat

Tender For supply of rotor assembly of ccu fan

State Government

CTN :45275642

02 Jun, 2026 3.07 Lacs

Serampore - West Bengal

Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging

Central Government/Public Sector

CTN :44340680

28 May, 2026 NA

Karimnagar - Telangana

Tender For corrigendum : procurement of lp turbine bladed rotor assembly of m/s gepil retrofitted210 mw machine installed at ntpc ramagundam stps.

Central Government/Public Sector

CTN :45291515

01 Jun, 2026 NA

Medak-T - Telangana

Tender For tender for supply of b7d1z44259 rotor allignment -diaph assy&disasy fixtr(w/o hyd.eqp) , clearance check fixture for rotor , support frame for diaphr(200-300series ) , support frame for diaphr(400 series ) , cplg asy/disasy fixt w/o hyd eqpt- d greater than equalls to 70 , cplg asy/disasy fixt w/o hyd eqpt- d equals to 50 , diaph assy&disasy fixtr(w/o hyd eqp) , rotor alignment fixture dia70 , dbse 500 , rotor align fixt dia40 , 50 , 60 dbse 500 , screw jack stand assembly , diaph asy&dsasy fixt-bcl400 wo hd eqpt , thrust collar fixture -for t brg 5inch & 6inch

State Government

CTN :45289480

30 May, 2026 NA

Palamau - Jharkhand

Tender For renovation of electro mechanical items for rural ws scheme, lesliganj - part a (raw water p/plant mali river at sitadih ), cost towards repairing and overhauling of 50 h.p. v.t. pump set multiple stage ball assembly s/f impeller g.m. bush as per sample 5 nos each, s/f housing bush as per sample. replace in spider rubber cutless bush 5 nos, replacing of 25mm dia. 5 feet long s.s. line shaft 4 nos with s.s. socket . transportation charge from site to work shop vice versa including tools tackles and labour charges for lifting & lowering v.t. pump before and after repairing work etc all complete at pumping plant., supplying all labour tools and tackles for complete opening, dismantling , cleaning of its slots of stator by brush & petrol then complete rewinding of 50 h.p. 440 volts, 50 c/s, star delta, 3 phase hollow shaft v.t. motor by supplying super enameled copper wire & binding, tapping varnishing, heating, testing on full load and repairing of stator & rotor, changing of bearings as per sample skf make with including the deduction of cost of burnt copper wires and transportation charges from p/plant to workshop and back to the same . including tools & tackles and labour charges etc all complete at p/plant., cost towards repairing/ replacement of 200 amp motor control panel board consisting of incoming feeder mccb 200 amp 1 no. and outgoing feeder mccb 100 amp 2 nos, timer 1 no., thermal over load release relay 2 nos. supplying and fitting of digital volt meter (0-500v) squared type 2 nos, ammeter (0-125amp) squared type 2 nos and replacement of phase indicator lamp 3 nos. including internal wiring etc all complete., cost towards supplying & fitting 35 mm2 3 core copper conductor 15 mtr panel to motor., cost towards supplying & fitting 60 watt led street light (jsor-m840), part b (clear water lesliganj.), cost towards repairing/ replacement of 200 amp motor control panel board consisting of incoming feeder mccb 200 amp 1 no. and outgoing feeder mccb 100 amp 3 nos, timer 1 no., thermal over load release relay 3 nos. supplying and fitting of digital volt meter (0-500v) squared type 2 nos, ammeter (0-125amp) squared type 2 nos and replacement of phase indicator lamp 3 nos. including internal wiring etc all complete., supplying all labour tools and tackles for complete opening, dismantling , cleaning of its slots of stator by brush & petrol then complete rewinding of 20 h.p. 440 volts, 50 c/s, star delta, 3 phase induction motor by supplying super enameled copper wire & then tapping varnishing, heating & testing on full load and repairing of stator & rotor, changing of bearings as per sample skf make with including the deduction of cost of burnt copper wires and transportation charges from p/plant to workshop and back to the same . including tools & tackles and labour charges etc all complete at p/plant., cost for repairing of 20 h.p. c/f pump with m/s/f s.s. shaft as per sample 1 no. c.i. gland tightner 2 nos, c.i. bearing housing 2 nos, ms. check nut 2 nos, c.i. neckring 2 nos, ball bearing s.k.f. as per sample 2 nos, all labour tools & tackles and materials with loading and unloading transporting charge from site to workshop & vice versa., cost towards varnishing, heating of winding & greasing of both side ball bearing of 25 h.p. induction motor 3 phase, 1440 rpm, volt 410 10% 50 cycle along with supplying & fitting of tyre coupling 2 nos, then testing on full load at site including supply of all labour tools and tackles., cost for repairing of 25 h.p. c/f pump with m/s/f s.s. shaft as per sample 1 no. c.i. gland tightner 2 nos, c.i. bearing housing 2 nos, ms. check nut 2 nos, c.i. neckring 2 nos, ball bearing s.k.f. as per sample 2 nos, all labour tools & tackles and materials with loading and unloading transporting charge from site to workshop & vice versa., supplying all labour tools and tackles for complete opening, dismantling , cleaning of its slots o

CTN :45303084

02 Jun, 2026 NA

Agra - Uttar Pradesh

Tender For supply of spark plug , fuel pump motor , brg clutch release , packing permofed , solenoide switch , cover gasket , push rod , control valve , disk brake pad , wiper blade , wiper blade rear with arm , rear brake shoe , assy kit lined shoe rear , tall lamp assy , regulator assy rh , disc clutch , oil seal , damper pulley

CTN :45148620

19 Jun, 2026 40.0 Thousand

Delhi - Delhi

Tender For corrigendum : supply of hyd cyl rep kit , fuel pump motor , armature assy , bush plate , oil pressure switch , auto tensioner , throttle cable assy , transmission over haul kit , piston ring kit , main bearing kit

CTN :45311975

09 Jun, 2026 64.80 Lacs

Multi City - Rajasthan

Tender For requirement of complete rotor assembly for lnt make ring granulators at chp, ssctps, suratgarh

CTN :45309836

04 Jun, 2026 89.09 Lacs

Chhabra - Rajasthan

Tender For supply of rotor assembly for l and t make ring granulator model no. 1017u installed at chp, csctpp, chhabra

CTN :45308383

09 Jun, 2026 64.80 Lacs

Ganganagar - Rajasthan

Tender For requirement of complete rotor assembly for landt make ring granulators at chp, ssctps, suratgarh

Fuel Pump Motor Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government / Public Sector

State Government

Central Government/Public Sector

Central Government/Public Sector

State Government