Latest gauge plate Tenders | Government gauge plate Tenders

State Government

CTN :43117029

17 Dec, 2025 NA

Delhi - Delhi

Tender For sic of submersible pump set and all allied e/m equipment for rebored tube well near h.no.-116c shahpur jat in greater kailash constituency ac-50. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 10 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point:200 lpm on 90 mtr. head. having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved make, supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted.a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no.b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 noc) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no.e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable bankingg) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos. complete wiring & installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated & pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs.make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., s/o nut & bolts of 1/2 dia of different size i.e. 1.5 dia& 2.5 long full threaded., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 8-10 inch diameter made out from 6mm thick m.s. sheet in 2 halves & a circular hole in centre 3-1/2 dia. with locking arrangement by nuts & bolt., earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government/Public Sector

CTN :43138097

31 Dec, 2025 NA

Mumbai - Maharashtra

Tender For supply and installation of stainless-steel plate children helpline number 1098

Central Government/Public Sector

CTN :43130796

31 Dec, 2025 42.26 Lacs

Madurai - Tamil Nadu

Tender For supply of 15wled decorative warm white down light fittings,supply of 15wled cool white down light fittings,18wled pin type decorative warm white lamp,36 40w led decorative warm white down light fittings,36 40w led decorative cool white down light fittings,200w led flood light fittings lumen 20000lm,300w outdoor led flood light fittings,supply of 100w indoor led flood light fittings,18w 20w retrofit type t8 led tube lamp 4ft,18wled tube lamp batten t5 model,stainless steel body type hand dryer,3 pole 40a 415v ac 2 no 2 nc contactor,supply of 4 pole 200a 415v ac 2 no 2 nc,3 module modular metal switch box,6 module modular metal switch box,8 module modular metal switch box,3 module modular switch box base plate,6 module modular switch box base plate,8 module modular switch box base plate,230 v 6a 3 pin modular socket 2m,230v 16a 1 way modular switch confirming,supply of 1.5 sq.mm 1100v pvc insulated,supply of 2.5 sq mm 1100v pvc insulated,supply of 4 sq mm 1100v pvc insulated,supply of 3c x 2.5 sq.mm copper conductor,supp

Central Government/Public Sector

CTN :43116943

19 Dec, 2025 10.68 Lacs

Delhi - Delhi

Tender For procurement of various spares for hyster and kone rst in area 1 at icd tkd - steering axle link plate (drg no. link plate hy-01) for hyster rst, material type- low alloy steel, vickers hardness no. (hv-5) 251.7, grade-is-2062:2011, gr-e-250 a (development item), frame (radiator fan) for hyster rst, til part no 4041208/ (as per drawing/sample), material type- low alloy steel, vickers hardness no. (hv-5) 163.3, grade- is-1239(part-1): 2004(amend-6:2021) (development item), shaft slew unit, p.no z9734001146 hyster/(developed) shaft slew unit, low alloy & carbon steel, hardness no. vickers 306.33(hv-5), steering axle link plate (drg no. link plate kn-01) of kone rst, (kone model no. smv 4531tb5) material type- low alloy steel, vickers hardness no. (hv-5) 240.3, grade- is-2062: 2011, gr-e-250 a (development item), rear boom pin bushing pn-h1622815/1 size: od-180mm, id-156mm & length -180mm (material-metlon), boom pin bush pn 1684558 size: od-135mm, id-120mm & length-100mm (material metlon), boom pin p n 1601121 size: od-156mm, id-70mm, length-235mm (material= en24)

Central Government/Public Sector

CTN :41185909

13 Dec, 2025 NA

Bangalore - Karnataka

Tender For bid to ras corrigendum : tender for supply of allen key set to metric ball ended hexagon key wrench set size 1 point 5 to 10mm chrome vanadium gun metal by chrome plated finish , allen key set to inches ball ended hexagon key wrench set 1 by 16 inches to 3 by 8 inches chrome vanadium gun metal by chrome plated finish , allen key set to metric hexagonal type size 1 point 5 2 point 0 2 point 5 3 point 0 4 point 0 5 point 0 6 point 0 8 point 0 10 point 0mm extra long chrome vanadium nickel plated as per din iso2936 , allen key set to inches size 5 by 64 inches 3 by 32 inches 1 by 8 inches 5 by 32 inches 3 by 16 inches 7 by 32 inches 1 by 4 inches 5 by 16 inches 3 by 8 inches long length chrome vanadium nickel plated as per din iso 2936 , allen key set to metric size 1 point 5 2 2 point 5 3 4 5 6 8 10mm standard length chrome vanadium nickel plated as per din iso 2936 , flap wheel 3 by 8 inches dia x 3 by 8 inches width to 120 grit 1 by 8 inches shank , flap wheel 3 by 8 inches dia x 3 by 8 inches width to 180 grit 1 by 8 inches shank , flap wheel 3 by 4 inches dia x 3 by 8 inches width to 120 grit 1 by 8 inches shank , flap wheel 3 by 4 inches dia x 3 by 8 inches width to 180 grit 1 by 8 inches shank , combination spanner set sizes 6 7 8 9 10 11 12 13 14 15 16 17 18 19 21 22 and 24mm ring head angled at 15 degree open end head angles at 15 degree chrome finish , tool box , tool box , ratchet to short handle 1 by 4 inches squre drive length 85 to 120mm number of teeth 60 working angle 6 degree reversible din 3122 by iso 3315 , palm control ratchet 1 by 4 inches square drive 60 by 72 tooth mechanism for 5 by 6 degree increments reversing by rotating cap or quick release safety lock bi to material elastomer grip as per din 3122 by iso 3315 overall length 90 to 125mm , palm control ratchet 3 by 8 inches square drive palm control ratchet 60 by 72 tooth mechanism for 5 by 6 degree increments reversing by rotating cap or quick release safety lock bi to material elastomer grip as per din 3122 by iso 3315 overall length 190 to 225mm , palm control ratchet 1 by 2 inches square drive 60 by 72 teeth mechanism for 5 by 6 degree increments palm control system ring reversing overall length 250 to 275mm , bit ratchet 1 by 4 inches square drive length 117 to 130mm reversible with 2 to component , combination spanner set size 5 5 point 5 6 7 8 9 10 12 14mm chrome alloy steel chrome plated as per din 3113 by iso 3318 , combination spanner set size 1 by 4 inches 9 by 32 inches 5 by 16 inches 11 by 32 inches 3 by 8 inches 7 by 16 inches 1 by 2 inches 9 by 16 inches chrome alloy steel chrome plated as perdin 3113 by iso 3318din 3113 , double ended ring spanner set size 7 by 32 inches 1 by 4 inches 5 by 16 inches 3 by 8 inches 7 by 16 inches 1 by 2 inches with plastic box or tray to accomadate chrome alloy steel chrome plated as per iso 691 by din 838 , double ended ring spanners set size 6 x 7 8 x 9 10 x 11 12 x 13 14 x 15 16 x 17 18 x 21 19 x 22mm with plastic box or tray to accomadate chrome alloy steel chrome plated as per din by iso 691 , combination ratchet wrench set sizes 6 7 8 9 10 11 12 13 14 15 16 17 18 19 21 22 and 24mm ring head angled at 15 degree open end head angled at 15 degree all sizes in a standard overall length chrome finish with thermoformed and foam tray as per din by iso 691 , combination reversible ratchet size 6mm 15 degree offset overall length 100 to 120mm chrome alloy steel chrome plated as per din by iso 691 , combination reversible ratchet size 7mm 15 degree offset overall length 120 to 140mm chrome alloy steel chrome plated as per din by iso 691 , combination reversible ratchet size 8mm 15 degree offset overall length 130 to 150mm chrome alloy steel chrome plated , combination reversible ratchet size 9mm 15 degree offset overall length 140 to 160mm chrome alloy steel chrome plated as per din by iso 691 , combination reversible ratchet size 10mm 15 degree offset overall length 150 to 170mm chrome alloy steel chrome plate

Central Government/Public Sector

CTN :42684765

16 Dec, 2025 7.35 Lacs

Ranga Reddy-T - Telangana

Tender For corrigendum : tender for supply of procurement of raw materials and fasteners c c - pure silver wire 99.9 percentage (minimum plus 0.01 - 0.04) , conforming to hal std 1356 size dia 3 mm or as per is 12144-1987 , m.s.rounds hal std 1001 is 1570-gr c-20 dia 7mm is 4855 class-i in 2-3 mtrs length , brass round hal std 1301 , is 319 , type-1 1/2hard , dia 4mm x 2 to 3 meters length , free cutting brass rod , conforming to hal std 1301 , condition 1/2 hard is 319-74 , type-i bs 2874 grade cz 121 size dia 6 x 2 to 3 meters in length , cold rolled brass sheet , strip and foil th cond half hardcuzn37 , is 410/ c27200 , astm b36/cz108 , bs2870/cu zn 37 , cw508l-en1652-r350/ th.0.3 mm , min. size 350 x 1200 mm. hal std 1300-hb. it should be protected with pvc coating morethan 50micro on both sides , cold rolled brass sheet , strip& foil th cond half hardcuzn37 , is 410/c27200 , astm b36/cz108 , bs2870/cu zn 37 , cw508l-en1652-r350/ th.0.4 mm , min. size 350 x 1200 mm. hal std 1300-hb. it should be protected with pvc coating morethan 50 micro on both sides , cold rolled brass sheet , strip& foil th cond annealedcuzn37 , is 410/c27200 , astm b36/cz108 , bs2870/cuzn 37 , cw508l-en 1652-r300/ th. 0.3 mm , min. size 350 x 1200 mm. hal std 1300-o. it should be protected with pvc coating morethan 50micro on both sides , electrolytic tough pitch copper foil condition half hard , conforming hal std 1310 / is 191-67 part v grade cu- etp and is 14811 , gr etp/ c11000 , astm b152 , size thickness 0.1 x 356 x 1220 mm with pvc coating on both sides in corrugated bobbin casing. , matrial copper (99.9 percentage min.) plate , condition aneealed , specification qq-c-521 grade a / c11000 , astm b152 , size thickness 15 mm x 1000 x 1000 mm , etp copper sheet 99.9 percentage , condition 1/2 h , conforming to hal std 1310 , is 191-80 (gr.etp) part v , 1972-77-1/2h , bs 2870 c 101 , size thickness 1.6 mm x 350 x 1200 mm with pvc coating on both sides. , al. round con to hal std 1251wp or is 733-75 , gr. (he-15) 24345 or bs 1476 , l64 , l87 , l168 , l65-t6 or qqa 351 gr. 17s or enaw 573-3-2014 dia 7mm x2 to 3 mtrs , glass filled phenolic moulding powder as per amity 16 / amity 157/ hal std 1757/is std 1300 , grade pf2 d4 , type d , filler glass fiber , glass natural colour , bimetal clad strip-grade 223-80 confirming to astm-b-388 size 0.4 x 25mm , hes fe-ni22-cr3 les fe-ni36 , plain washer m2 -gost 10450 class a (or) hal std -8062-m 2 c (d) , austenetic stainless steel as per aisi-303 se/304 (or) corrosion resistance steel as per gost5632 grade 1x18h9 - with passivation. , spring washer m2 -is 3063-or hal std - 8070 - m 2 b (c) - non magnetic (austenetic) stainless steel as per hal std 1206 or aisi -303 se /304 -passivation , hal std 8011 , cheese head screw -m2 x 10 austenetic stainless steel as per aisi-303/304se-passivation. , hal std 8105 , tubular eyelet (brass silver plating) 1.6x4

Central Government And Public Sector

CTN :43116013

30 Dec, 2025 18.98 Lacs

Leh Ladakh - Jammu And Kashmir

Tender For purchase of spares from the original manufacturer for 11kv vcbs (model vm12) of bhel make. - closing unit assembly, tripping unit assembly, motor cut-off limit switch assembly, mechanism shaft assembly, tripping spring assembly, closing spring set, top pole head, bottom pole head, spring charge motor 220v (ac/dc), operating coil 220v (dc), vcb support insulator ø118, panel / busbar support insulator ø75, lever for vi, drive link, d-lever assembly, centering ring, spherical rod end, spacer tube, support rod, compression spring, aux switch 16 way, emergency tripping assembly, plug & socket assembly (male + female)-32 pin (indoelectricals make), slow closing handle, motor charging handle, packer cu, flexible connection up to 1600a, bearing, rollers, dashpot, set of clips, indicator, truck nylon wheels, nylon rollers for shutter lifting, bolt for truck wheel, jaw contact assembly up to 1600a, jaw contact square cu packer, manual knob push button (red), manual knob push button (green), damping rubber pad, auxiliary rod, swing bolt, actuating arrangement, cam shaft for rack-in/out, 52c/d auxiliary bracket, vcb interphase barrier, jaw contact polycarbonate shroud up to 2500a, insulating coupler, door gasket (4.4 mtr/panel), door lock assembly, door glass, interpanel busbar smc sheet barrier, shutter arrangement, limit switch test/service, tripping lever/knob, cleat, nut, insulating screw m6x22, rear cover polyamide handle, packer (round), al spacer (round), support insulator 095, support channel, busbar screw (special), steel stud, clamp plate, packer, link plate inplace of droppers al, barrier, sealing cover, busbar joint pvc shroud, support channel round packer, earthing connection, pvc sleeve l/f 0.4x104 for 75wd busbar, pvc sleeve 38p for wiring, space heaters 75w, bolt hex m12x75-8.8, bolt hex m12x65-8.8, nut hex m12x8, washer spg-12-st, washer mcd 13-st, screw hex m8x30-8.8, washer spg-8-st, washer mcd 8.4-st, nut hex m8-8, m20 bolts for support insulator, nylon m5 screw, nylon m5 nut, screw hex m6x20-8.8, washer spg lock 5cb-6-5t, washer mcd 6.4-st, nut hex m6-8, bolt hex m16x65-8.8, washer spg lock scb 16-st, washer mcd 17-st, thol/con 220vdc thermal overload relay with power, contactor having 1nc aux. contact., dc diode plate, barrier for top fixed contact, barrier for bottom fixed contact, large barrier between ct

Central Government/Public Sector

CTN :43129619

26 Dec, 2025 NA

Hyderabad-T - Telangana

Tender For ms hot rolled steel plate as per is 2062

Central Government/Public Sector

CTN :43125979

31 Dec, 2025 NA

Goa - Goa

Tender For supply of dmr 249a steel plate size 8000x2500x16,dmr 249a steel plate size 8000x2500x12

Central Government/Public Sector

CTN :43115831

11 Dec, 2025 NA

Bokaro - Jharkhand

Tender For design, manufacture and supply of centrifugal vertical submersible sump pump with dry motor including companion flanges, base plates, foundation bolts, name plate, motors, coupling, coupling guard, commissioning spares and all other necessary auxiliaries including shim plate _package no. sm-807_, required for rebuilding of coke oven battery no. 8 at sail, bokaro steel limited, bokaro, jharkhand under limited competitive domestic bidding process.

Gauge Plate Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors