Latest grease purging machine Tenders | Government grease purging machine Tenders

CTN :43562910

28 Jan, 2026 NA

Kanpur - Uttar Pradesh

Tender For purchase of ahp transport air compressor dryer d d - strainer , sight glass , suction filter , service valve rotolock , pre filter element , oil separator , non return valve , needle valve , moisture separator , hand shut valve , hot gas bypass valve , hose vibration eliminator freon , oil filter , expansion valve angle valve , freon dryer , condenser watercooled , compressor ref , ball valve freon , after filter element , crank case heater , lubricating oil 160sz , pin valve copper relief valve or refill valve , copper tube 6.35 mm od 1by4 inch , copper tube ferrule 6.35 mm od 1by4 inch , copper tube 9.53 mm od 3by8 inch , copper tube ferrule 9.53 mm od 3by8 inch , copper tube 15.88 mm od 5by8 inch , copper tube ferrule 15.88 mm od 5by8 inch , copper tube 25.40 mm od 1 inch , copper tube 34.93 mm od 1 3by8 inch , copper tube 41.28 mm od 1 5by8 inch , copper tube 53.98 mm od 2 1by8 inch , copper 1 inch elbow 90 , copper 1 inch tee , copper 1 3by8 inch elbow 90 , copper 1 3by8 inch tee , copper od 2 1by8 inch elbow 90 , copper od 2 1by8 inch tee , copper tee 1 5by8 inch , copper reducer 1 5by8 inch x 1 3by8inch , copper reducer 1 3by8 inch x 1 inch , heat exchanger and evaporator ) /bid number : gem/2026/b/7089550 * /dated: 13-01-2026 & & / bid document 1 / 48

CTN :43563126

03 Feb, 2026 NA

Mumbai - Maharashtra

Tender For supply of 25bvlc001 boq d d - kit rear se3371 , belt water pump , valve solenoid 218 , manifold cover 5h40 , glass sight & hand hole cover , valve plate base , 3 8 rel val 300-350psicas san hen , air filter cell front withdrawal 602x602 x80mm alu strips , bellows neoprene , 7/16 unf (p) nylock , drier , suction gasket , valve plate , piston pin , compressor , extra safeties & controls , evaporating coil , condensing unit with marine condenser , oil return valve assembly , connecting rod cap assembly , l p cut out (0 10-1401) , hp switch , kit motor seal , diaphragm , hose , elbow , condenser , drive coupling suitable for our 5h80 , casing heater crank case , seal replacement assy auth dcpro e mopr(b) ema 3056 91 dt , washer carbon ring , conn rod assy 5h , piston , ring compressing , sleeve cylinder , comp ring 5h46 , suction strainer , zinc protector assy , oil ring , rubber tyre for drivecoupling drg.n , solonoid valve 2 1 8 ma4253 sporlan , filterdriermodel udk165 dryall , vbeltb68 , oil safety switch(danfossmake) , t.p. mainswitch63a , fuse fittings63a , anglevalve , spannertee1 2 , compressionring

CTN :43582755

24 Jan, 2026 NA

Bareilly - Uttar Pradesh

Tender For supply of mt spares d d - suction hose 75 mm - 8 m long , pump tyre foot lorry type , tyre 1400x20 22pr sch non direction , rubber hose radiator to thermostat , tyre inflator hose , air filter primary , retro-fitment of rear view mirror for , release bearing 442370585166 , drying distri unit hi pr voss , armature assy , assy mudflap rear , brush gear assembly , windshield assy flat , drive assy , element fuel water separator , halogen lamp 24v 75 70 w , turbo charger repair kit , catridge lub oil filter , assy blade wipper , air filter element safety , separater fuel water , major kit clutch master cyl repair , strainer fuel , flasher 24v , repair kit minor slave cylinder , head lamp bulb a 12v 45 40wdin 72601 , wiper timer 24v , assy clutch master cylinder , anchor hold fast bar , halogen bulb h4 24v 60 65w p45 t capt fo , 8 ton jack with handle , tin rectangular 5 ltrs , block wooden for jack

CTN :43588260

24 Jan, 2026 NA

Wardha - Maharashtra

Tender For supply of charger fire ext co2 gas cartridge , ext fire water air stored pressure , breathing apparatus contained , basket strainer suction 100mm 4 , wrenches suction 75mm 3 , coupling instantaneous female 63mm x 70 mm , branch pipe hand cont 63mm gm is903 , ext fire dry powder 50 kg capacity , bucket iron 330mm , washer rubber 100mm , branch pipe foam making fb 10x i 2097 , breaded hose 60mtr , nozzle fog extension applicator with , siren hand operated , measure cylindrical pouring type 200ml , shoes safety magazine s8 , measure conical 1 ltrs

CTN :43590716

17 Jan, 2026 NA

Malda - West Bengal

Tender For supply, installation and commissioning work of water floating fountain (ring type) with supply fixing of all necessary item like pump with strainer connected at suction, light, controller, flat cables, nozzles with necessary fitting and ball joint, including transportation installation demonstration.[ warranty period: 30 months after the date of delivery ]

corporations/Associations/Others

CTN :42707910

16 Jan, 2026 4.03 Crore

Lucknow - Uttar Pradesh

Tender For bid to ras corrigendum : supply of tata and leyland filter bs 6 c c - def tank filter ul2. 2 bs- 6 , spin on oil filter 80k bs-6 , air filter primary h6-bs-6 , air filter safety h6-bs-6 , def tank filter 24l breather bs-6 , def tank filter for neck bs-6 , pre fuel filter n4 h6 bs-6 , air filter for def tank bs-6 , def tank filter for suction of def bs-6 , strainer bs-6 , fuel filter fuel water separator spin o bs-6

CTN :42916529

20 Jan, 2026 16.90 Lacs

Baran - Rajasthan

Tender For corrigendum : supply of spare/accessories items of two nos. multi-purpose fire tender(rj-28ea-0956 and rj-28-ea-0957) - 1 high pressure hose reel with 60mmlg x 19 mm (ø) with fog gun and spray type , 2 low pressure hose reel with 19 mm ø x 50 mm long hose with duel purpose shut off nozzle. 3 extension ladder 10.5 metre , 4 delivery hose 63 mm rubber lined in 30 m length (type a of is 636/79/5) complete with instantaneous coupling. , 5 long line 50 mm circumference 30 m long as per is 1084 , 6 short line 50 mm circumference 15m length as per is 1084 , 7 protective clothing for fireman complete with golves,boots,helmets with suitable face shield made out of material capable of reflecting at least 95% of radiant heat temperature around 1500 to 2000 degree celsius and also afford some protective against direct flame.the suit will be of sufficient size to accomodate a breathing apparatus to users (item should be packed in hard body box). , 8 fire hook , 9 fire man axe , 10 sledge hammer , 11 carpenter saw , 12 pick axe , 13 ceiling hook , 14 crow bar made of carbon steel , 15 self contained breathing apparatus (45 min duration compressed air type) complete with spare cylinder & tool kit) , 16 dividing breeching , 17 collecting breeching , 18 pvc suction hose heavy duty complete with copper alloy round threaded couplings to suit the pump inlet - 2.5m long. , 19 suction strainer for item 2 , 20 basket strainer suitable for item 4 , is : 3582 , 21 dividing breaching with control arrangement as per is : 5131 , 22 collecting breaching as is : 905 , 23 hose bandages rubberized is : 5612 , 24 hose clamps is : 5612 , 25 water curtain nozzle made of m .s .plate with g . m instantaneous connection , 26 branch pipe short ( chromium plated) is : 903 , 27 a set nozzle of sizes 12 mm , 16 mm , 20mm , 25 mm and 32 mm ( two each ) ( see is : 903 - 1975 * t ) , 28 adapter for 100mm suction female thread and 63mm male instantaneous 29 adaptor double female instantaneous pattern 63mm . , 30 adaptor double male instantaneous pattern 63mm , 31 hand lamp ( 4cells ) , 32 rubber gloves 33kv 1 pair , 33 fire beater , 34 foam pick up tube , 35 rubber gloves as per is 4770 - 1991 for 5000 volts , 36 leather gloves is 6994 – 1977 , 37 jack hydraulic for 20 ton capacity with handle , 38 hand controlled branch for 63 mm size hose coupling , 39 hand held fast action select flow nozzle :-the selectable flow rate multipurpose nozzle should have a multiple flow setting. this product be of light in weight and easy to handle. weight of the nozzle should not be more than 2 kg. the calibrated flow rates are easily selectable through an selection ring. the stream patterns should be changed by rotating the diffuser head ring. nozzle should be having pistol grip, shut off ball valve opening and made of aluminum alloy. , 40 bolt cutter – 600mm long , 41 shovel with handle , 42 minimum 12v halogen fog & spot lamps , 43 hose ramp

State Government

CTN :43340681

20 Jan, 2026 70.00 Lacs

Wayanad - Kerala

Tender For corrigendum : ridf xxviii - lift irrigation projects in various padashekharams of wayanad district- procurement of submersible pumpsets, fittings, accessories, and related electrical works - procurement, installation, erection, testing, and commissioning of pumpsets and allied works at punchavayal, manikkuni, kolembetta, valiyavattam, and padiyeri pumphouses. - procurement, installation, erection, testing, and commissioning of pumpsets and allied works at punchavayal, manikkuni, kolembetta, valiyavattam, and padiyeri pumphouses., supply, installation, erection, testing, commissioning and fitting charges for all accessories of horizontally mounted submerged centrifugal non clog pump set of compact unitary mono-block submerged single/multi stage,volute type casing with suitable radial type impellers on common shaft for pump and motor ,anti friction bearing with life time greasing, protection features with sensors to monitor temperature,mechanical seal leakage ,etc.(the pump should be confirming to his/is standards).the moc of pump,casing-cast iron,impeller -ss cf8m,shaft-ss-316,suction strainer -ss and other as per is standard.the motor should be suitable for 3 phase,415v /-10%,50hz /5%,ac supply submersible motor having class f /h insulation, air filled and ip-68protection confirming to is 325 or latest standards suitable for day night operation.the pump discharge capacity of 230 cubic metre /hour against duty point head of 42 mtrs, working head range 18 - 47m, discharge range 136 - 57 lps ,speed 1450rpm(n) or nearer ,with 10meters of copper power cable and control cable, railing arrangement. the pump should be painted with three coats of suitable anti corrosive paint over priming coat. the electrical works for the pumpset should be completed as per kseb rules and regulations and the contractor is responsible for arranging premissions and certificates from the electrical inspectorate. the suction side of the pumpset should be provided with an additional iron grill for preventing foreign particles inside the inlet side of the pump casing., supply and erection of 60hp auto transformer starter (ats) with suitable incommer and contactors including 24 kvar capacitor with required indications ,metering and protections for single phasing ,overload, pump monitoring unit to protect from ingress, high temperature level etc enclosed in a closed panel board, supply and laying additional termination cable of 1.1kv 3.5 core 95sqmm aluminium conductor xlpe insulated ;steel armoured ug cable as per relevant is 7098 with support for cable, supply, installation, erection, testing, commissioning and fitting charges for all accessories of horizontzlly mounted submerged centrifugal non clog pump set of compact unitary mono-block submerged single/multi stage,volute type casing with suitable radial type impellers on common shaft for pump and motor ,anti friction bearing with life time greasing, protection features with sensors to monitor temperature,mechanical seal leakage ,etc.(the pump should be confirming to his/is standards).the moc of pump,casing-cast iron,impeller -ss cf8m,shaft-ss-316,suction strainer -ss and other as per is standard.the motor should be suitable for 3 phase,415v /-10%,50hz /5%,ac supply submersible motor having class f /h insulation, air filled and ip-68protection confirming to is 325 or latest standards suitable for day nightoperation.the pump discharge capacity of 188 cubic metre /hour against duty point head of 35 mtrs,working head range 16 - 42m, discharge range 102 - 42 lps ,speed 1450 rpm(n) or nearer ,with 10meters of copper power cable and control cable,railing arrangement. the pump should be painted with three coats of suitable anti corrosive paint over priming coat. the electrical works for the pumpset should be completed as per kseb rules and regulations and the contractor is responsible for arranging premissions and certificates from the electrical inspectorate. the suction side of the pumpset should be provided wi

CTN :43547169

27 Jan, 2026 NA

Uttara Kannada - Karnataka

Tender For tender for supply of hf type fuse , rating 4a , motor protection relay 415v ac , 50hz , 240v ac , 50hz , , ps 3-8 rg pipe , 2 x pg13.5 suitable cable dia 5-14mm , blower complete with motor. model vr-50-2 1 80 m3 hr , , power contactor coil voltage 120v ac , with inbuilt 1no aux , power contactor-1no-50hz-110v , add on contact- 2no 2 nc , power contactor for mnx18 contactor , coil 240v ac , 50hz , indicating lamp 120vac 50hz , green colour , led type , indicating lamp 120vac 50hz , green colour , led type , indicating lamp 120vac 50hz , white colour , led type , ammeter range - 0-150a dc , size - 72x72 , type no. - smi-72 , voltmeter range - 0-250v dc , size - 72x72 , type no. - smi-72 , mpr300bb010 , 110vac-50hz , relay contacts 1no 1nc-1-2.75a , mpr300bb040 , 110vac-50hz , relay contacts 1no 1nc-4-11a , macerator , pump only , cover , suction chamber , rotating knife , macerator compl , nut for flap valve , flange w-connecting pipe dn50 , screw , m10x170 , fan , fan cover , l-coupling , screw , m8x20 , screw , m8x20 , screw , m8x35 , nut , m5 , washer , m6 , screw , m6x16 , o-ring , sealing ring , o-ring , rubber flap , orifice , shaft seal i 35 mm , ball bearing , ball bearing , flow orifice , indicating lamp red colour lens , 120v , indicating lamp green colour lens , 120v , voltage monitoring relay three phase , ammeter 0-100a , dc suitable external shunt 50mv , size 72-72mm , voltmeter range 0-250v dc , size 72x72 , type no. smi 72 , solenoid valve 1-4 , fd valve wvpc-v , complete , sheet and cover , comfort , release button , level controller gwt , y-strainer , 1-2 , pvc , sched 80 -threaded , valve , 1 swing check , pvc , control relay 5a , relay with 230v ac retaining clip , solenoid valve 1 2-2 way direct acting , pump fresh water (hydrophore pump , pump centrifugal monoblock pump in moc ss316 , size-32 x 32mm , controller , flow , 0.5 gpm , control relay 110vac , 50-60hz tesys k2 no 2 nc , overload relay 4.0 6a with spp , lrd-10 , gasket , neoprene , for 1-2-150 flange , gasket , neoprene , for 1 -150 flange , gasket , neoprene , for 1-1-2 150 flange , gasket , neoprene , for 2 -150 flange , gasket , neoprene , for 3 -150 flange , gasket , neoprene , for 4 -150 flange , valve , solenoid , 1-4 , brass , 120v mounted at control panel , 1 hp motor-tefc - baldor ip-56 , seal kit -mechanical seal , bushing , and o ring , 5-8 coupling flange-pump side , axial cutter , radial cutter , impeller washer , cutter ring , 17-4ph , 7-8 coupling flange-motor side , impeller , dechlor replacement tube , santoprene , 2 pk , dechlor replacement tube , santoprene , 5 pk , relay , control , 24 vdc , din , 1pdt , relay , power , 40adc , dpdt , orifice plate , titanium , for 1 t-u ball valve -unsized , rod all thread , 1-2 x 4 brass , bolts , 5-16 , 316 ss , washer , flat 3-8 316 ss , book cell assembly , 4-6-8m , complete cell unit , sealant , silicone , handle , chrome plated , pvc true union ball valve socket - 1-2 , pvc true union ball valve socket - 3-4 , pvc true union ball valve socket - 1 , pvc true union ball valve socket - 1 1-2 , pvc true union ball valve socket - 2 , pvc true union ball valve socket - 3 , pvc one piece flange socket - 1-2 , pvc one piece flange socket - 3-4 , pvc one piece flange socket - 1 , pvc one piece flange socket - 1 1-2 , pvc one piece flange socket - 2 , pvc one piece flange socket - 3 , pvc one piece flange socket - 4 , pvc check valve - 1 1-2 , pvc check valve - 2 , pvc tee socket - 3-4 , pvc tee socket - 1 , pvc tee socket - 1 1-2 , pvc tee socket - 2 , pvc y strainer - 1-2 , pvc cap fipt - 1-2 , pvc female adapter socket x esr fjpt - 1-4 , pvc female adapter socket x esr fjpt - 1-2 , pvc female adapter socket x esr fjpt - 3-4 , pvc female adapter socket x esr fjpt - 1 , pvc female adapter socket x esr fjpt - 1 1-4 , pvc female adapter socket x esr fjpt - 1 1-2 , pvc female adapter socket x esr fjpt - 2 , pvc male adapter socket x mipt - 1-2 , pvc male adapter socket x mipt - 3-4 , pvc male adapte

CTN :42842817

20 Jan, 2026 16.90 Lacs

Chhabra - Rajasthan

Tender For corrigendum : supply of spare/accessories items of two nos. multi-purpose fire tender(rj-28ea-0956 and rj-28- ea-0957)against tn-sc-638/2025-26(mm) - high pressure hose reel with 60mm lg x 19 mm ( ) with fog gun and spray type, low pressure hose reel with 19 mm x 50 mm long hose with duel purpose shut off nozzle., extension ladder 10.5 meter, delivery hose 63 mm rubber lined in 30 m length (type b of is 636/79/5) complete with instantaneous coupling., long line 50 mm circumference 30 m long as per is 1084., short line 50 mm circumference 15m length as per is 1084., protective clothing for fireman complete with golves, boots, helmets with suitable face shield mad out of material capable of reflecting at least 95% of radiant heat temperature around 1500 to 2000 degree celsius and also afford some protective against direct flame. the suit will be of sufficient size to accommodate a breathing apparatus to users (item should be packed in hard body box)., fire hook, fire man axe, sledge hammer, carpenter saw, pick axe, celling hook, crow bar made of carbon steel, self contained breathing apparatus (45 min duration compressed air type) complete with spare cylinder & tool kit), dividing breeching, collecting breeching, pvc suction hose heavy duty complete with copper alloy round threaded couplings to suit the pump inlet - 2.5m long., suction strainer for item 2, basket strainer suitable for item 4 , is : 3582, dividing breaching with control arrangement as per is : 5131, collecting breaching as is : 905, hose bandages rubberized is : 5612, hose clamps is : 5612, water curtain nozzle made of m .s .plate with g . m instantaneous connection, branch pipe short ( chromium plated) is : 903, a set nozzle of sizes 12 mm , 16 mm , 20mm , 25 mm and 32 mm ( two each ) ( see is : 903 - 1975 * t ), adapter for 100mm suction female thread and 63mm male instantaneous, adaptor double female instantaneous pattern 63mm ., adaptor double male instantaneous pattern 63mm, hand lamp ( 4cells ), rubber gloves 33kv 1 pair, fire beater, foam pick up tube, rubber gloves as per is 4770 - 1991 for 5000 volts, leather gloves is 6994 1977, jack hydraulic for 20 ton capacity with handle, hand controlled branch for 63 mm size hose coupling, hand held fast action select flow nozzle :-the selectable flow rate multipurpose nozzle should have a multiple flow setting. this product be of light in weight and easy to handle. weight of the nozzle should not be more than 2 kg. the calibrated flow rates are easily selectable through an selection ring. the stream patterns should be changed by rotating the diffuser head ring. nozzle should be having pistol grip, shut off ball valve opening and made of aluminum alloy., bolt cutter 600mm long, shovel with handle, minimum 12v halogen fog & spot lamps, hose ramp

Grease Purging Machine Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

State Government