Latest hand file Tenders | Government hand file Tenders

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

Central Government/Public Sector

CTN :45682056

15 Jul, 2026 NA

Tiruchirappalli - Tamil Nadu

Tender For supply of stored pressure fire extinguishers of mechanical foam type with a capacity of 09 litres, conforming to is 15683:2018 (or latest), designed for effective fire fighting against class b fire and having fire rating of 4a, 144b. the extinguisher shall be constructed from stainless steel materials conforming to clause 9.2.6 of is 15683:2018. the foam concentrate shall be aqueous film forming foam (afff) confirming to is 4989:2018. the unit shall be equipped with flexible hose and foam applicator nozzle. a brass or stainless steel squeeze grip valve shall be provided in accordance with clause 9.3 of is 15683. test certificate from nabl accredited laboratory for the test pressure (pt) of the assembled unit as mentioned in clause 6.1 of is 15683:2018 shall be provided along with supply. each unit shall be supplied with a wall bracket or stand for secure mounting and shall include maintenance instructions for annual inspection by certified personnel. marking shall be as per clause 10 of is 15683:2018 with the year of manufacture permanently engraved or embossed. complete documentation including user manual, warranty, and certification details must be provided with each extinguisher. [ warranty period: 30 months after the date of delivery ] ]

State Government

CTN :45697547

10 Jul, 2026 NA

Kotdwar - Uttarakhand

Tender For procurement of auto electrician and electronics trade equipments allen key set of 12 pieces, back probe tools, caliper inside, calipers outside, center punch, dividers, electrician screw driver, hammer ball peen, hands file, logic probe, pliers combination, screw driver, screw driver, scriber, spanner d.e. set of 12 pieces, spanner, ring set of 12 metric sizes, spanners socket with speed, handle, t- bar, ratchet and, steel rule 30 cm inch and metric, steel tool box with lock and, key (folding type), test light, wire cutter and stripper, ac alternator slip ring puller, adjustable spanner, air blow gun with, standard accessories, air impact wrench with, standard accessories, air ratchet with standard, accessories, allen key set of 12 pieces, ammeter, angle plate adjustable, angle plate size, anti theft device, auto electrical test bench, battery -charger, battery terminal cleaner tool, battery tester, belt tensioner gauge, blow lamp, caliper inside, calipers outside, car jet washer, car stereo, chisel, chisels cross cut, circlip pliers expanding and, contracting type, clamps c, clamps c, clamps c, cleaning tray, copper bit soldering iron, dc ohmmeter, depth micrometer, dial gauge type 1 gr. a, (complete with clamping devices, and stand), distributor -duel advance type,, reluctance type, dividers, drift punch copper, drill point angle gauge, drill twist, electric soldering iron 230 v 25, watts, electric testing screw driver, electrical horns ( different types ), engineer's square, executive auto electrical tool kit, feeler gauge 20 blades (metric), file flat, file, half round, file, square, file, square, file, triangular, files assorted sizes and types, including safe edge file (20 nos), flat file, flat file, glow plug tester, granite surface plate, grease gun, growler, hacksaw frame adjustable, hammer ball peen, hammer chipping 0, hammer copper, hammer mallet, hammer plastic, hand operated crimping tool (i), for crimping up to 4mm and, (ii) for crimping up to 10mm, hand reamers adjustable, hand shear universal, hand vice, high rate discharge tester (cell, tester), hollow punch set of seven, pieces, insulated screw driver, insulated screw driver, left cut snips, lifting jack screw type, magneto spanner set with 8, spanners, magnifying glass, marking out table, multimeter digital, multi-point fuel injection pump, oil can, oil stone, oscilloscope, outside micrometer, outside micrometer, outside micrometer, outside micrometer, philips screw driver set of 5 pieces, pliers combination, pliers flat nose, pliers round nose, pliers side cutting, portable electric drill machine, portable headlight aiming kit, prick punch, punch letter 4mm (number), scriber, scriber with scribing black, set of stock and dies - metric, soldering copper hatchet type, spanner clyburn, spanner d.e. set of 12 pieces, spanner t. flocks for screwing up, and up- screwing inaccessible, positions, spanner, adjustable, spanner, ring set of 12 metric sizes, spanners socket with speed, handle, t-bar, ratchet and, universal upto 32 mm set of 28, pieces with box, spark lighter, spark plug spanner, steel measuring tape, steel rule, steel rule, straight edge gauge, straight edge gauge, stud extractor set of 3, stud remover with socket handle, surface gauge with dial test, indicator plunger type i.e. 0.01 mm, tachometer (counting type), taps and dies complete sets (5, types), taps and wrenches - metric, telescope gauge, temperature gauge, tester sparking plug 'neon' type, thermostat, thread pitch gauge metric, bsw, timing lighter, universal puller for removing, pulleys, bearings, v' block, vernier caliper, vice grip pliers, voltmeter, wire gauge (metric), work bench, 4 point relays, 5 point relays, air bag simulator, air conditioned mpfi vehicle, with auto transmission and, air conditioning service unit (car), air conditioning trainer kit, alternator assembly used for lmv, arbor press hand operated 2, ton capacity, general installation/ machineries, cut section model of moc

CTN :45484591

24 Jun, 2026 NA

Jalandhar - Punjab

Tender For bid to ras supply of g1 10410886 5340-000969 padlocks ig 4 levers 75 mm , k5 10537169 3740-000165 sprayer insecticide manually h o 16 l , k7 10376023 dmd-niv-2050 mech foam ext of 9 ltrs cap with co2 , f1 10417674 5133-000206 augers hand nominal size (mm) 25 , f1 10411517 5120-000777 extractor cotter pin 250 mm , f1 10547773 5110-000454 handle file 90mm , f1 10551783 5120-003039 spanner open jaw fixed de 19x22mm , f1 10416873 5133-000575 augers hand nominal size (mm) 20

CTN :45345533

18 Jun, 2026 10.15 Lacs

Lalpur - Gujarat

Tender For corrigendum : supply of bending machine conduit pipe , bus bar with brackets 1 mtr , cctv camera kit , ceiling fan coil winding machine , conduit pipe cutting and threading machines , control panel , digital multi meter , discrete component trainer , dmx controller 512 , ev charger home 1 phase input , ev charger 3 phase input , file half round 2nd cut 250 mm with handle , file round 2nd cut 150 mm with handle , knife switch dpdt fitted with fuse terminals 16 amp , knife switch tpdt fitted with fuse terminals 16 amp , ladder - tower 3 meters on tyre wheels - min 10ft - max. 30ft , lux meter lcd read out 0.05 to 7000 lumens with battery. , magnetic flux meter , mallet barwood , meter reading instrument mri , potential transformer 415 v, 50hz, pt ratio, 440v.110v,10va , power factor meter digital , primary current injection set , rcc pole with accessories , rechargeable battery 12v,100ah , rubber mat , single phase transformer , single phase variable auto transformer , smart meter 3 phase - smart energy meter , soft starter , solar dc pump 1 hp , solar panel with battery 18 watt , solar street light , solar traffic light , solid state solar base single phase energy meter , spanner d.e. set , tachometer analog type - 10000 rpm , three phase transformer , wheat stone bridge ) /bid number : gem/2026/b/7576252 * /dated: 27-05-2026 & & / bid document 1 / 40

CTN :45354205

12 Jun, 2026 NA

Jodhpur - Rajasthan

Tender For bid to ras supply of f1 5120-001104 drifts pin brass parallel 12 5 x 160 mm , f1 5120-002565 spanner magneto and distributor set , k1 7105-000038 cases tool barbers , j1 knd niv camp 64 lnr inr with pv dd fabr for tefs 2m unit , k5 7330-000230 measure conical 1 ltrs , f1 5120-000303 handle hammer 915 mm , f1 5120-000213 claws tack lifter , f1 5110-000455 handle files 115 mm , f1 5120-001650 spanner box tubular hexagonal steel plat , f1 5120-002985 pliers side cutting 150 mm

CTN :45404122

19 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using

Central Government/Public Sector

CTN :45458977

17 Jun, 2026 NA

Multi City - Punjab

Tender For auction sale of depot miscellaneousellaneous scrap - scrap of used and condemned hand tools like pipe wrench 12",18",ratchet handle, sockets, 36,30,32,24mm ,spanner 10-11,24-46,24-27,30-32 ,adopters, wire cutter, torque wrench., pliers, extension rod , screw driver, pipe wrench 10,14",18",24",plastic pipe cutter 42mm,pop rivet machine(manual) , pneumatic sika applicator gun 310ml,600ml, manual sika applicator gun 310ml and other miscellaneous hand tools of various types ,make,sort & sizes with or without ferrous and non ferrous attachment with broken/unbroken, damaged etc (qty shown in the lot is approximate) pl no-98090331

Central Government/Public Sector

CTN :45449054

20 Jun, 2026 40.00 Lacs

Kamrup - Assam

Tender For supply of combination pliers , screw driver , neon tester , electrician knife , hammer ball pin , file round , plier side cutting , plier round nose , plier flat nose , pliers long nose , hammer chisel , hammer ball peen , wall jumper octagonal mm , center punch , steel measuring tape , allen keys , spanner double ended set of g , adjustable spanner , steel rule , electric soldering iron , rubber gloves , multimeter , tong tester , megger , dc power supply , auto transformer variac , tweezers , crimping tools , common hacksaw , adjustable hacksaw , hand saw , dhau , round knife , tripura dhahu , foldable knife , multi purpose knife , common scissors , hand drill , electric hand drill , steel rule , folding scale , bamboo cross cutting machine heavy duty , bamboo portable crosscutting mc , bamboo radial splitting mc chain type , bamboo round stick making machine , bamboo stick polishing machine , bamboo slicing machine heavy duty , bamboo stick sizing machine , bamboo double side cutting machine, parallel splitter , bamboo four side planing machine , bamboo treatment plant , bamboo dying tank , bamboo knot removing machine , manual slivering machine , universal grinding machine , machine saw , machine planner , hand gloves , portable sanding machine , spray gun , dying chamber , resign applicator , glue mixing machine , spade , steel float , spirit level , chisel , bench vice , c. clamp , gloves canvas , grinding machine with various polishing stones , brush for painting , automatic weaving machine , gas torch , woodturning lathe , table grinding machine , industrial sewing machine , clamps for holding or tightening the jobs , manual ball press machine , sizing machine for window blinds , compressor , manual slivering machine , portable planner , mitre saw , universal planner , suitable work tables , tool cabinet , trainees locker with , storage rack

CTN :45361817

12 Jun, 2026 5.15 Lacs

Kargil - Jammu And Kashmir

Tender For supply of dental items and consumbles d d - k files ss no 6 25mm set of 6 , k files ss no 8 25mm set of 6 , k files ss no 15 length 21 mm set 6 , k files ss no 15 length 25mm set 6 , k files ss l 21mm size no 15 40 set 6 , k files ss l 25mm size no 15 40 set 6 , hyflex rotary file 21mm pack 6 , hyflex rotary file 25mm pack 6 , protaper hand file niti 25mm set 6 , hand protaper sx f3 25mm dentsply , gutta percha point f1 , gutta percha point f2 , gutta percha point f3 , paper point f1 , paper point f2 , paper point f3 , ketac molar 3m , gic type 1 , gic type 2 , gic type ix , temporary filling material cavit g , water based calcium hydroxy paste , metapex root canal filling material , gluma desensitising liquid , alveogyl haemostatic dressing , mouth ulcer gel , stolin gum paint , wooden wedges for dental use , youni dental floss , dental floss thread mint pack 3 10 meter , applicator tips , patient bib plastic , disposable patient bib , interdental proxa tooth brush , colgate sensitive soft tooth brush , thermoseal ra tooth paste , lignocaine 2 per plain 30ml , matrix band universal , dettol hand wash pouch , antiseptic wipes , finishing bur yellow ring bur , endo acces bur kit , surgical bur tc straight fissure , ruixin tungsten acrylic trimming bur hp 060 cross cut , bp blade size no 15 , disposable pmt set , disposable plastic matrix band with retainer , gas rifill for blow torch dental premium buntane gas , nitrile non sterile gloves medium , nitrile non sterile gloves small , disposble glass of 100 ml , disposable shoe cover pack 100 dispenser , pop for dental use , wax knife dental lab , lecron corver , wire cutting plier , adams plier , rapid repair material liqiud and powder , rotarory retreatment files niti pack 06 assorted 25 mm , resin based root canal sealer , chx 2 per root canal irrigant 100ml //bid details 2 / 48

Hand File Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

State Government

Central Government/Public Sector

Central Government/Public Sector