Latest horizontal pump repair Tenders | Government horizontal pump repair Tenders

CTN :43343214

06 Jan, 2026 NA

Jammu - Jammu And Kashmir

Tender For supply of filter bowl fuel , washer tab fly wheel , set screw fly wheel , dust coverfly wheel , cable step control , joint timing case , cir clip gudge on pin , air filter oil both type , fan , pully , bracket eng mtg , fan belt , fan extension , pully alternator , pipe assy alternator inlet , pipe assy alternator outlet , lever adj alternator , stud eng mtg bracket , switch starter , cut out and regulator , cable stop control , cable idling control , pipe fuel , pipe atomizer over flow , pipe fuel injection , oil fuel injection , oil pressure guage , water temp guage , sprink pipe , parking brake liner , parking brack ribit , head light bulb , head light glass , reflector , cabin celling light assy , clutch bolt , gear box top cover gaskit , oil filter , fuel filter , hydraulic filter , air leaf valve , feet pump , pipe line tank to pump , thermostate valve , solenoid 12v , brake shoe , water pressure gauge , oil temperature gauge ) /bid number: gem/2025/b/7047618 * /dated: 26-12-2025 & & / bid document1 / 38

CTN :43344820

05 Jan, 2026 NA

Amritsar - Punjab

Tender For supply of armature assy 24v , solenoid switch 24v , brush gear assy , carbon bush set 24v , self bush set , speedo rpm meter , fuel feed pump assy

CTN :43343382

05 Jan, 2026 NA

Jalandhar - Punjab

Tender For supply of sa pump coolant alt pt no b 7016008 , speed sensor agb alt f 2015600 , gasket and seal set , drive assy , epicycloidal gear train , battery cut off switch , element air cleaner , oxygen sensor , speedometer cable , clutch cable assy , throttle cable assy

CTN :43274899

30 Dec, 2025 NA

Ranchi - Jharkhand

Tender For the supply of spare parts of vehicles and other equipment used in vehicle servicing on rate contract basis--c dynamo bracket, ac pump, temperature head unit, air filtter box, hydraulic cylinder piston, hydraulic cylinder rod, complete hydraulic cylinder, assembly, hydraulic pipe tank to cylinder, pto lever, pto lever kit, pto pump, pto seal kit, oil drain bolt, slip ring, hydraulic cylinder seal kit, hydraulic cylinder piston, hydraulic cylinder piston rod, complete hydraulic cylinder, assembly, main begin bearing, pressure switch rear, pressure switch front, mobile filter body, ecm complete, brake shoe lock, gear tappa, engine packing kit, rear axle bearing, clutch fork patti, mobile seperator, diesel returning jali pipe, silencer complete set, ecm complete, steering repairing kit, wiring harness complete, break vecamp, house pipe, slip ring, stator, stator coil, pulli, condensor, body aassembly upper & lower, patti fig, kit set, wiring harness, pinion, pinion gear, main bearing bering, water steel pipe, dynamo adjuster, finger kit, housing bolt 15-17-19 no, clutch paddel, gear handi, gear tappa, gear chainjer flang no-1-, 2/3/4/5 and back fork, gear frok swing boll, gear frok rod, gear chanzer kit, gear shaft katori, gear lattu, ring(kangan) bearing, gear box flange tapa, gear dry nut, tapa pinion washer, shaft bolt no- 17,15,19, center bearing flange, tel crown complete, crown handi cage, cage bolt, break adjuster kit, self parts, pinion, head unit, dynamo bracket, head seat, rear rubber pipe, cng reducer, hydraulic cylinder piston, hydraulic cylinder rod, complete hydraulic cylinder, assembly, hydraulic pipe pto to tank, hydraulic pipe tank to cylinder, anti dirt plug, pto pump, pto cable, slip ring, regulator cut out with carbon, electrifire set, startor, rotor, bearing, carbon plate, bearing plate, carbon, armature, carbon rocker, bearing bush, lever & frok, solenoid switch, armature lock, field coil, pinion lock, pinion, fan relay, heater timer, fuse box, fuse, head ligh & back light, head light bulb, head light holder clip, kilometer, hour meter, dashbord meter, terminal red, terminal balck, terminal mouth, ignition switch, heater plug, commination switch, head unit, horn patti, main glass with rubber guide, rubber guide, left & right side glass with rubber, guide, radiator fan, looking mirror, engine block, crank shaft, piston and pin, main bearing bering, connecting rod, connecting bush, cam shaft, oil pump complete, cam pinion, engine pully, timing plate, crank thrust washer, mobil chamber, crank pinion, timing oil seal, piston pin, engine full packing kit, stating pully, push rod, push guide, connecting bolt, engine chapa bolt, crank cam key, complete head, head wall, complete hub front, head guide oil seal, head seat, head gaskit, nozzle pipe, radiator, complete radiator

CTN :43332072

05 Jan, 2026 1.85 Lacs

Sagar - Madhya Pradesh

Tender For tender for supply of oil seal , oil seal rear , seal front oil 32x47x6 , oil seal , ring set piston std , bearing set crank shaft , cam shaft , pulley cam shaft timing , tensioner comp timing belt , spring tensioner , valve intake , valve exhaust 4 valve mpfi , valve assy , sensor water temperature , hose outlet , muffler , pump assy fuel , filter assembly fuel , pump assy oil , pump assy oil , clutch assy fan , thermostat , hose radiator , hose radiator outlet no 1 , valve assy solenoid , filter , cover assy clutch , gear t m main shaft 5th , half engine assy 4 valve mpfi , engine overhaul kit , engine overhaul kit consists of 45 items

corporations/Associations/Others

CTN :43287647

05 Jan, 2026 NA

Tuticorin - Tamil Nadu

Tender For ttps operation circle mpm i unit i complete dismantling of mill 1f and reassembling the dismantled spares in mill 1b - draining of mill gearbox oil completely, cleaning the gearbox internals like worm shafts and worms wheel. after inspection filling the gearbox with new/old oil including devolution of old oil to stores etc, (department vehicle will be provided for drawl of oil at free of cost)., charges for dismantling the gear coupling bolts, gear coupling (worm shaft only), distance piece, unscrewing the worm shaft extension cover bolts and bearing housing cover bolts, removing the worm shaft extension cover, lowering to ground floor, releasing the worm shaft assembly from its position and assemblies providing back the overhauled worm shaft assembly in the gear box and fitting back the worm shaft extension cover, bolting and tightening the bolts to the required torque level and assembling back the gear coupling bolts, distance piece etc., charges for dismantling the worn out rubber element in the mill motor coupling, cleaning inspection and replacement of new rubber element and checking the tightness of coupling including cost of consumables etc.,, charges for dismantling the spool pieces, multiple port outlet bodies and transition pipes 4 nos. each after assembling the coal pipe inspection with center feed pipe structures., charges for removal of orifice 1 no. after dismantling the victaulic coupling., charges for removal of mill journal doors including lead, lift and transporting of materials fromstores and devolution of scraps from site to stores and cost of consumables such as welding electrodes, gas, cotton waste etc.,, charges for removal of journal with trunnion assembly in the mills including lead, lift and transporting of materials from mill repair bay to mill floor and back, devolution of scrap to stores and cost of consumables such as welding rod, cutting gas, cotton waste etc., charges for changing of bowl extension ring (6 nos) per mill including lead, lift and transporting of materials from stores to mill floor and back, charges for dismantling of lube oil cooler, from lube oil system, cleaning, flushing the cooler, oil pipe lines, water pipe lines, oil separator tank, checking of water lines, valves and nipples., charges for providing wedges between lower skirt and mill insulation cover plate firmly, removal of gearbox bottom cover flange bolts, lowering the thrust bearing and pump housing after supporting lower radial bearing housing. lowering the thrust bearings and reassembling of all the above parts, charges for lifting the vertical shaft along with worm gear and worm wheel from top of the gear box and place it in stand. dismantling the worm wheel hub lock nut and removal of worm wheel from the worm hub by steam/induction heating. inspection of upper redial bearing and renewal if necessary., charges for dismantling and removing worn out thrust bearing of mill vertical shaft by gas heating the racer, cleaning the bearing seating area in the vertical shaft., charges for removing the thrust bearing adopter (worn out) and assembling the new adopter by heating, charges for removal of seperator body along with classifier assembly. inner cone mill outlet plate and venturi dismantling the air inlet housing after segregating from hot air duct placing in appropriate place. dismantling the bowl with bowl hub and separating the bowl hub from bowl and in filling the same., charges for dismantling of upper skirt assembly, lower skirt assembly, mechanical face seal assembly, dust guard and blue matching of seal runner, renewal of seal( bronze), air seal, dismantling of mill bottom cover, upper bearing housing cover, oil seals etc.,, charges for dismantling the triangular liners, cutting the bulged mill bottom plate, applying refractory cement at the mill bottom plate 1 set by providing bolts and welding., charges for dismantling the radial bearing after removing the oil pump hub and oil pump bushing., charges for changin

corporations/Associations/Others

CTN :43287648

05 Jan, 2026 NA

Tuticorin - Tamil Nadu

Tender For ttps operation circle mpm i unit i complete dismantling of mill 2f and reassembling the dismantled spares in mill 1c - draining of mill gearbox oil completely, cleaning the gearbox internals like worm shafts and worms wheel. after inspection filling the gearbox with new/old oil including devolution of old oil to stores etc, (department vehicle will be provided for drawl of oil at free of cost)., charges for dismantling the gear coupling bolts, gear coupling (worm shaft only), distance piece, unscrewing the worm shaft extension cover bolts and bearing housing cover bolts, removing the worm shaft extension cover, lowering to ground floor, releasing the worm shaft assembly from its position and assemblies providing back the overhauled worm shaft assembly in the gear box and fitting back the worm shaft extension cover, bolting and tightening the bolts to the required torque level and assembling back the gear coupling bolts, distance piece etc., charges for dismantling the worn out rubber element in the mill motor coupling, cleaning inspection and replacement of new rubber element and checking the tightness of coupling including cost of consumables etc.,, charges for dismantling the spool pieces, multiple port outlet bodies and transition pipes 4 nos. each after assembling the coal pipe inspection with center feed pipe structures., charges for removal of orifice 1 no. after dismantling the victaulic coupling., charges for removal of mill journal doors including lead, lift and transporting of materials fromstores and devolution of scraps from site to stores and cost of consumables such as welding electrodes, gas, cotton waste etc.,, charges for removal of journal with trunnion assembly in the mills including lead, lift and transporting of materials from mill repair bay to mill floor and back, devolution of scrap to stores and cost of consumables such as welding rod, cutting gas, cotton waste etc., charges for changing of bowl extension ring (6 nos) per mill including lead, lift and transporting of materials from stores to mill floor and back, charges for dismantling of lube oil cooler, from lube oil system, cleaning, flushing the cooler, oil pipe lines, water pipe lines, oil separator tank, checking of water lines, valves and nipples., charges for providing wedges between lower skirt and mill insulation cover plate firmly, removal of gearbox bottom cover flange bolts, lowering the thrust bearing and pump housing after supporting lower radial bearing housing. lowering the thrust bearings and reassembling of all the above parts, charges for lifting the vertical shaft along with worm gear and worm wheel from top of the gear box and place it in stand. dismantling the worm wheel hub lock nut and removal of worm wheel from the worm hub by steam/induction heating. inspection of upper redial bearing and renewal if necessary., charges for dismantling and removing worn out thrust bearing of mill vertical shaft by gas heating the racer, cleaning the bearing seating area in the vertical shaft., charges for removing the thrust bearing adopter (worn out) and assembling the new adopter by heating, charges for removal of seperator body along with classifier assembly. inner cone mill outlet plate and venturi dismantling the air inlet housing after segregating from hot air duct placing in appropriate place. dismantling the bowl with bowl hub and separating the bowl hub from bowl and in filling the same., charges for dismantling of upper skirt assembly, lower skirt assembly, mechanical face seal assembly, dust guard and blue matching of seal runner, renewal of seal( bronze), air seal, dismantling of mill bottom cover, upper bearing housing cover, oil seals etc.,, charges for dismantling the triangular liners, cutting the bulged mill bottom plate, applying refractory cement at the mill bottom plate 1 set by providing bolts and welding., charges for dismantling the radial bearing after removing the oil pump hub and oil pump bushing., charges for changin

CTN :43321880

03 Jan, 2026 NA

Parganas - West Bengal

Tender For tender for supply of washer(price list sl-239) , spacer(page-03) , ratchet(price list sl-538) , roll pin , starter handle(price list sl-539) , starter rope(price list sl-504) , power head gasket set (13 nos items)(sl-434) , starter lock lever , bushing(page-07) , washer , screw , clamp , clip , ignition coil(ctlg sl-17) , spacer , lanyard assy(mariner plate elect component) , clamp , bushing , washer , nut , fuel pump assy (price list sl-566) , gasket , float needle , carburetor repair kit (containing 11 nos items) , clamps , upper end cap , cylinder head , spark plug(ngk-b7hs-10) (sl-464) , exhaust cover , crankshaft , piston (standard)(ctlg sl no 14) , piston set (standard)(sl-477) , ball bearing , reed block assembly , lockwasher , washer , friction plate , upper thrust plate , buttom yoke(black) , set plate , bracket , wave washer , wave washer(sl-9) , collar(sl-19) , washer , water plug , plug , trim tab , cam rod (long) , bushing , pinion gear(sl-479) , pipe , oil seal(sl-418) , dowel pin , water pump repairs kit (containing 07 no of items) , holder(price list sl-54) , needle bearing

CTN :42996744

26 Dec, 2025 NA

Garhwal - Uttarakhand

Tender For bid to ras bid to ras supply of cycle with 10 gear , cycle with 12 gear , chain 10 spead , 10 speed cassette , disc brake pads , front chainwheel , hydraulic disc brake lever back , hydraulic disc brake lever rear , shift lever 10 speed , 10 oblique 11 speed rear derailleur , bottom bracket , chain 12 speed , 12 speed cassette , 12 speed rear deraileur , 12 speed mechanical shifter black , tube air pump , suspension pump , 12 speed crank set , gear wire , water bottle , cycle helmet , tubeless tyre 29 inch , tube 29 inch , tool kit , multi tool lkey , saddle , suspension rork , spoke 29 wheel , chain lube , mineral oil brake fluid , seat clamp , high precision stopwatch , clit pedal , outer cable , throw excel , cones , hanger 09 speed , hanger nut , direct mount chainring teeth 32 , wd 40 , direct mount chainring teeth 34 , watch lanyard

CTN :43322080

05 Jan, 2026 NA

Doda - Jammu And Kashmir

Tender For supply of radiator pipe , oil seal , uj kit propeller shaft , needle brg nk 55 35 , stg gear box oil seal , cabin shock absorber , water pump assy , tail lamp assy , shroud assy , revoling light assy beacon light , accelerator rod set

Horizontal Pump Repair Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

corporations/Associations/Others