Tender For supply of rate contract for spares for parker make spares - pump (parker) part no.-t6c0103r03b1, 1/2" filter/regulator with mounting bracket part no.-p32ea14esabngp, 1/4" filter/regulator with mounting bracket part no.-p31ea12ebbngp, accumulator part no.-a4em0218l670h , accumulator part no.-a6em0578, air breather 3 micrometer rating, part no.-h00834004, b.c. ret. filter part no.-933117q, bowl real service kit part no.-rk22137 5540611800, brake pre. filter part no.-932630q, bucket control valve, part no.-1110.2204-012, ser 222104, bucket control valve, part no.-1110.2204-012, ser-000000189803, chain reel motor, part no.-30391106.40, sery1010-07096, chain reel motor, part no.-312.9218.042, se n1010-03823, charge pump part no.-5541-7432-00/0301359/ ser no. x111544322 parker-0301359, check valve part no.-d4a040 / nmk2, coil part no.- s8ld, coil (24vdc/20w) for the above part no.-s10ld , coil 24v dc part no.-20w, coil, solenoid, 24v part no.-851025, coolant filter element (recharge) part no.-5540524000/2350789/bw5140, cushion valve pre range 2000-2599 psi part no.-915a000045034 dwv-75-a-2500, directional valve part no.-e2b040z215nmk31516, dump lever, max psi 500 part no.-hc-379, dump line pre. reducing valve part no.-prh081s10-6t1138, b08-3-6t, engine oil filter element part no.- b9601 , f/w separator part no.-r60p, filter part no.-32630q 3000 23 wr, flow control valve, part no.-fs800s, 699052138293, fuel filter element part no.- bf900 , fuel water separator element, r90p part no.-, fuel water separator for lpdt ejc30s & pc th205l part no.-r-120t, high pressure filter element part no.-170z 222a, hyd. motor (compr.) part no.-3349212097, hyd. perc. (return) filter element part no.-937112q , hyd. pump part no.-3239110389, hyd. pump part no.-3239529166, hyd. pump part no.-3349122281, hyd. pump part no.-3349122265, hyd. pump part no.-3782009, hyd. pump part no.-324 9110 457, hyd. pump part no.-3129310176, hyd. pump part no.-t6cc-014-005-1r00-c1-00 , hyd. pump (brake) part no.-3129112553, hyd. pump (carrier) part no.-3269120007, hyd. pump (rot.) part no.-7029530011, hyd. pump (rotation) part no.-3339111656, hyd. pump (strg.) part no.-3129622160, hyd. pump (strg./d & h) part no.-3239120227, hyd. pump (tandem) part no.-3249120258, hyd. return filter part no.-1-c1096/11-524, hyd. return filter part no.-pr4467, hyd. return filter part no.-ucr6131, hyd. return filter part no.-fc1096/ff524, hyd. suc. filter part no.-921166, hydraulic filter element part no.-g01315q , hydraulic filter element part no.-925520, hydraulic filter element part no.-935145, hydraulic motor, part no.-3217903420/3349219084, hydraulic oil filter part no.-0060d010bn4hc 1250487m, hydraulic pump (rot., b/rb 281) part no.-3249529007, hydraulic pump (strg. & dump/hoist) part no.-3129612019, kit seal part no.-9121669650, kit seal part no.-9121591350, kit seal part no.-9120099014, kit, repair for relief valve (h1-05-12mp) part no.-h1 kit, kit, seal part no.-3217983409/3469149201 , kit, seal for the above, service kit, f300-26 part no.-3911802119, kit, seal, direction valve section part no.-398000k801, load control valve part no.-e2a060z-20-241, lp element, part no.-937967, sf1-r-40, lever (hand) part no.-6760382, motor (hose drum) part no.-3782009, o ring service kit no. 3 , o ring service kit no. 4 , o ring service kit no. 5 , o ring service kit no. 6 , o ring service kit no. 7 , o ring service kit no. 8 , overcenter valve part no.-e2b040z300nmk3, overcenter valve part no.- e2b040znmk3, pre relief valve part no.-rdh103510 mexico 1223, pre. accumulator ade075-21r9a2 v075l ps 210 bar t8-30/80 deg. c075-7315-028-641 , pre. red/relieving valve part no.-prn101510 mexico 1230, pressure switch, part no.-psb040af1a5x811, pump part no.-3217955410, pump (brake & str) part no.-3269120007, pump (brake) part no.-3129620173, pump (dump & hoist) part no.-3129320258, pump (dump & str) part no.-3039122108, pump (hyd.) part no.-3249115 023 , pump, part no.-5561847200, pu
Tender For tender for supply of brush carrier assy , assy handle outer door lh , door lock lh , assy rear view mirror outer rh , spider clutch , bulb g12 v 10w din 72601 , ring spanner 12x13 mm , hose rubber 4 id 65mm long , brg bush fxg bkt , water proof starter motor 5 8 kw 24v
Tender For rerouting of existing of 400mm dia coramandal bulk water supply pipe line with ms carrier pipes and 800mm dia casing pipe (thatipudi source) at railway crossing portion through horizontal direction drilling technique method near railway bridge no.1655 pole no. 872/21/1 to 872/23 at nad fly over of gvmc under deposit contribution work
Tender For corrigendum : supply of fabrication and erection work e e - places , replacing wornout runner base and installing a new runner base of cane carrier and baggage elevator and r b c , replacing wornout runner with new one of cane carrier and baggage elevator and r b c , removing wornout angle iron and t iron of the cane carrier and reinstalling it by straightening the crooked part , removing the wornout part of the suit from different places and fitting it with new one , chevron grooving of new rollers of the mill , chevron grooving of old rollers of the mill , remove the wornout partition plates of the juice box above and below the juice heater by 10 or 12 mm ms plate and install it , installing ribs at the top and bottom partitions of the juice heater , repairing save all of qurdbody , removing old wornout gutters installed at various places and installing it with new gutters , remove the old wornout save all from pan and quard and install it with new one , reinstalling the new umbrella fitted inside the pan by making a new one and removing the old one , replacement ribbon arm of the mascute receiving crystallizer , making new separator of a centrifugal machine , removing the wornout truff of the hopper and installing it with new one , making and installing new separators for continuous centrifugal machines , removing the tubes of quad juice heater and dynamic juice heater and expanding them by installing new tubes and giving their hydraulic testing satisfactory of size 42 mm , removing the tubes of pan installing new tubes and expanding them and giving hydraulic tesing with satisfactory trial of size 96 mm , removing the wornout flue gas ducting of both the boilers and installing it with newone making from new or old plates , removing the wornout front and roof plate at boiler number 1 and 2 and installing with a new plate , removing the damaged boiler damper and installing a new one , making bagasse suit and installing. , replacement of juice over flow box of clarifier , making and installing bed of motor and pumps at various places as per requirement , replacement 6 inch dia cooling pipe of sulfur furnace , removing the monitor casing of a machine from old machine and installing it and giving its a trial , making amd replacing manholes at various places , making and replacing the enternals of cather of the pan. , making and replacing the new hood of cane cutter , removing the old bottom plate of the lowest compartment of the clarifier and placing a new plate on it after placing an angle trap as per the instructions and giving a satisfactory water trial , reinstalling the stirrer of the clarifier and giving a satisfactory trial , removing the shaft of a pug mill and replacing the old bushes on both sides and fitting new ones , removing and refitting the shaft of a brown sugar magma mixer and installing with new bush , reinstalling the trufff of connecting rod of the hopper , making and installing new catcher strainer , removing the old rail line of the trolley of the unloader and fitting the new rail line satisfactorily and doing water level , reinstalling the old rail line of the unloader s bridge and fitting it and checking water level etc , removal of old and weak channels of 3 inches to 10 inches diameter installed at various places and installation of new ones as per requirement , cutting and straightening old plates installed at various places as per requirement , removal of old and wornout scrubber installed on sulfur furnace and making and replacing with 8 or 10 mm plate and making all the connections , removing the trufff plate including support corroded shell and top cover plate of the top chamber of the clarifier and fitting the new plate and giving it s a water proof trial , re-installation alignment and //bid details 2 / 47 trial of hopper driving end , making and installing the top cover of the centrifugal machine , making an arm and installing it on the shaft of pug mill , making and installing scrubber and bot
Tender For supply of wiper motor 24v , battery cut off switch , brush carrier assy , self bush set , bulb fog lamp 12 volt , relay 24v , relay turn signal , wiper blade , wiper blade rear , hose water inlet , gasket exhaust manifold , fuel hose , assy hose , fan belt , suspension bush kit , alternator belt , ac filter