Tender For corrigendum : supply of spares for atlas capco two stage rotary feeder screw air compressor : : -kit mint 4000h part no. 2906049200 , zr 450 to 750 8000h maint kit part no 2906049300 , valve solenoid part no 1089943916 , valve solenoid part no 1089943918 , speqar element part no 1621073500 , o ring part no 663213200 , roto z 20l part no 2908850101 , zr500 to 750 16000h maint kit part no 2906049500 , set rubbers 8 piece part no 1619646708 , elektronikon mk5 i by 02 part no 1900520033 , elektronikon mk5 i by 034part no 1900520042 , temperature sensors part no1089057470 , sensors press part no1089962518 , sensors press part no1089962514 , pressure sensors part no1089057595 , pressure sensors part no1089057592 , cable part no 1614812601 , cable part no 1830103709 , kit mk5s lpwa with antenna part no 1837032036
Tender For supply of spares for optical floating zone equipment model no. fzt-4000-h-vpo-pc - halogen lamps 1000 w ( 24 pcs/ set), o-ring for quartz tube normal pressure p50 (pack containing 5 nos) for quartz tube high pressure v50 (pack containing 5 nos) o-ring for shaft p20 (pack containing 5 nos) o-ring dia 10 mm for hydrostatic press (pack containing 20 nos) o-roing dia 20 mm for hydrostatic press (pack containing 20 nos), seed holder 6 mm (including ceramic seed holder) (pack containing 5 nos), feed holder (hook) (pack containing 5 nos), upper shaft with screw hole (inside the tip) ( pack containing 3nos), rubber tube for making feed rods (6mm diameter, 250 mm length, one side open) 100 nos per pack, quartz tube (normal pressure) 50 mm diameter x 2 mm thick x 305 mm long ( 3pcs/set)
Tender For tender for supply of 01.size clear opening diameter 800 mm 02.color green on both sides.the handles to be marked with photo luminescent tapes. 03.opening mechanism-escape scuttles are to be spring assisted and provided with a wheel assembly on the inside and a slot with a detachable operating handle from outside for opening and closing of the scuttles.the operating handle should be supplied with associated bulkhead-mountable press-fit clamps to enable securing the operating handle onto the bulkhead. 04.material- as per class requirement 05.all ees are to be flush type spring assisted with auto retention clip and operable from above and below by one person.they are to be provided with an opening arrangement from above with detachable operating handle and press-fit clamps for securing the handle on to the nearest bulkhead. 06.ees are required to operable from both sides and tested up to 1.2 bar pressure or as per class requirement 07.marking- each scuttle should have punch mark with oem name date of fabrication month and year .marking symbols should be prominent legible and i.a.w. with nes118 and nes119. 08.rubber beading-rubber beading of silicone as per ncd 5910 are to be used for the ees , on board spares for ess consisting of the following -1.ss nuts and bolt sets- 10 nos -2.ss screws-10 nos -3.brass washers-10 nos -4.split pins-04 nos -5.silicon rubber beading-04 mtrs -6.adjustable spanner-01 nos , documentation -1.class approved drawings- 01 nos. -2.technical -operating-installation-testing and maintenance manual-01 nos. -3.inspection release note-inspection reports of inspection agency-certified test reports-materialtest reports-certificate for dimensional accuracy weight certificates with position of c.g etc-01 nos. -4.soft copy of all above documents in cd or pen drive-01 nos. , 01.size clear opening diameter 800 mm 02.color green on both sides.the handles to be marked with photo luminescent tapes. 03.opening mechanism-escape scuttles are to be spring assisted and provided with a wheel assembly on the inside and a slot with a detachable operating handle from outside for opening and closing of the scuttles.the operating handle should be supplied with associated bulkhead-mountable press-fit clamps to enable securing the operating handle onto the bulkhead. 04.material- as per class requirement 05.all ees are to be flush type spring assisted with auto retention clip and operable from above and below by one person.they are to be provided with an opening arrangement from above with detachable operating handle and press-fit clamps for securing the handle on to the nearest bulkhead. 06.ees are required to operable from both sides and tested up to 1.2 bar pressure or as per class requirement 07.marking- each scuttle should have punch mark with oem name date of fabrication month and year .marking symbols should be prominent legible and i.a.w. with nes118 and nes119. 08.rubber beading-rubber beading of silicone as per ncd 5910 are to be used for the ees , on board spares for ess consisting of the following -1.ss nuts and bolt sets- 10 nos -2.ss screws-10 nos -3.brass washers-10 nos -4.split pins-04 nos -5.silicon rubber beading-04 mtrs -6.adjustable spanner-01 nos , documentation -1.class approved drawings- 01 nos. -2.technical -operating-installation-testing and maintenance manual-01 nos. -3.inspection release note-inspection reports of inspection agency-certified test reports-materialtest reports-certificate for dimensional accuracy weight certificates with position of c.g etc-01 nos. -4.soft copy of all above documents in cd or pen drive-01 nos. , 01.size clear opening diameter 800 mm 02.color green on both sides.the handles to be marked with photo luminescent tapes. 03.opening mechanism-escape scuttles are to be spring assisted and provided with a wheel assembly on the inside and a slot with a detachable operating handle from outside for opening and closing of the scuttles.the operating handle should be supplied with associate