Latest hydro meteorological information system Tenders | Government hydro meteorological information system Tenders

CTN :45346428

15 Jun, 2026 NA

Madurai - Tamil Nadu

Tender For purchase of renewable energy practical equipments - equipments for renewable energy practices:, rc phase shift oscillator oscillator type: rc phase shift oscillator using transistor / op-amp configuration. input supply: 230 v / 50 hz ac with regulated internal dc supply. output frequency range: 100 hz 10 khz adjustable. output: sinusoidal waveform with adjustable amplitude up to 10 vpp. rc network: three-stage rc phase shift network with frequency control arrangement. cro test points: dedicated cro terminals at amplifier output, each rc stage, and final output for waveform and phase-shift observation. protection: over-voltage and short-circuit protection provided. indicators and controls: power on led indication with frequency and gain adjustment controls. accessories: patch cords, circuit diagram, strain guage characteristics kitac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords, load cell characteristics kit input supply: 230 v / 50 hz ac with regulated internal dc supply. sensor: strain gauge load cell with suitable mounting arrangement. load range: 0 10 kg. display: digital display for load/output indication. cro / test points: test points provided for observing bridge output, amplifier output, and signal conditioning stages. controls: zero adjustment and calibration controls provided. protection: overload and short-circuit protection provided. accessories: loading arrangement, connecting leads., measurement of tank level using rotometer input supply: 230 v / 50 hz ac with regulated internal dc supply. tank arrangement: transparent tank with 30 liters capacity with suitable supporting stand. rotameter range: 0 4000 l/hr calibrated rotameter. flow system: pump, control valves, and piping arrangement provided for continuous flow operation. measurement facility: provision for flow-based tank level measurement and observation. display / observation: calibrated level indication with flow monitoring arrangement. test points: output terminals provided for monitoring sensor/output signals. accessories: connecting tubes., measurement of tank level using displacer type level transmitter input supply: 230 v / 50 hz ac with regulated internal dc supply unit. measurement principle: buoyancy (archimedes principle) using displacer element. tank arrangement: transparent experimental tank with 30 liters capacity and suitable mounting stand. level range: suitable laboratory-scale level measurement (0 100% tank height). sensor system: displacer type level transmitter with continuous level output signal. display unit: digital indicator for level display in percentage / engineering units. output signals: standard analog output (4 20) ma / (0 10) v provided for monitoring. test points: provided for transmitter output, signal conditioning, and display unit verification. controls: zero and span calibration adjustment provided for setting level reference. protection: over-voltage and short-circuit protection for electronic modules. accessories: connecting cables, piping arrangement, loading medium (water), measurement of temperature using pt100 input supply: 230 v / 50 hz ac with regulated internal dc power supply unit. sensor: pt100 resistance temperature detector (rtd) probe with stainless steel sheath. measurement principle: resistance variation of platinum element with temperature. temperature range: 0 c to 150 c (or suitable laboratory range). display unit: digital temperature indicator with direct c display. accuracy: high accuracy with linearized rtd signal conditioning circuit. sign

CTN :45346446

11 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For purchase of lab equipments for res dept - purchase of lab equipments for res dept, rc phase shift oscillator (iemcode:o001)specifications: oscillator type: rc phase shift oscillator using transistor / op-amp configuration. input supply: 230 v / 50 hz ac with regulated internal dc supply. output frequency range: 100 hz 10 khz adjustable. output: sinusoidal waveform with adjustable amplitude up to 10 vpp. rc network: three-stage rc phase shift network with frequency control arrangement. cro test points: dedicated cro terminals at amplifier output, each rc stage, and final output for waveform and phase-shift observation. protection: over-voltage and short-circuit protection provided. indicators and controls: power on led indication with frequency and gain adjustment controls. accessories: patch cords, circuit diagram., strain guage characteristi cs kit(iemcode:o002)specifications: ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. no rs.10,000 2 table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords, load cell characteristi cs kit(item code: o003)specifications:input supply: 230 v / 50 hz ac with regulated internal dc supply. sensor: strain gauge load cell with suitable mounting arrangement. load range: 0 10 kg. display: digital display for load/output indication. cro / test points: test points provided for observing bridge output, amplifier output, and signal conditioning stages. controls: zero adjustment and calibration controls provided. protection: overload and short-circuit protection provided. accessories: loading arrangement, connecting leads., measurement of tank level using rotometer(item code: o004)specifications: input supply: 230 v / 50 hz ac withregulated internal dc supply. tank arrangement: transparent tank with 30 liters capacity with suitable supporting stand. rotameter range: 0 4000 l/hr calibrated rotameter. flow system: pump, control valves, and piping arrangement provided for continuous flow operation measurement facility: provision for flow-based tank level measurement and observation. display / observation: calibrated level indication with flow monitoring arrangement. test points: output terminals provided for monitoring sensor/output signals. accessories: connecting tubes., measurement of tank level using displacer type level transmitter(item code: o005)specifications: input supply: 230 v / 50 hz acwith regulated internal dcsupply unit. measurement principle:buoyancy(archimedesprinciple) using displacerelement tank arrangement: transparent experimental tank with 30 liters capacity and suitable mounting stand. level range: suitable laboratory-scale level measurement (0 100% tank height). sensor system: displacer type level transmitter with continuous level output signal. display unit: digital indicator for level display in percentage / engineering units. output signals: standard analog output (4 20) ma / (0 10) v provided for monitoring. test points: provided for transmitter output, signal conditioning, and display unit verification. controls: zero and span calibration adjustment provided for setting level reference. protection: over-voltage and short-circuit protection for electronic modules. accessories: connecting cables, piping arrangement, loading medium (water), measurement oftemperature using pt100(item code: o006a)specifications: input supply: 230 v / 50 hz ac with regulated internal dc power supply unit. sensor: pt100 resistance temperature detector (rtd) probe with stainless steel sheath measurement principle: resistance variation of platinum element with temperature. temperature range: 0 c to

CTN :45322006

01 Jun, 2026 NA

Panipat - Haryana

Tender For rc/purchase of workshop tool / general consumables material (part-1) > - araldite, make- pidilite (1.8kg packing), sr-998, make: pidilite, ( per kg), m-seal (per kg.), make: pidilite, locktite -406 (per 20ml), make: hankle, blue tube paste (set), hold tite (kg.), make-pidilite, rustolene (per ltr), birkosit sealing compound, dunlop adhesive (kg.), safeda (zink white powder) (per kg), graphite powder (kg.), make-vicco, lock tite 641 standard make (50 ml), lock tite 401 standard make (set), safety solvent standard, molikote paste 1000 (pkt./tube), molykot- g rapid plus, molykot- d-321 spary, molykot spray 1000 (400 ml), molykot grease 1000, molykot-z powder (per kg), anabond 666 (100gram), molykot spray l-0500, stag-b compound jointing (per kg), dp test kit set of 03 bottles, make: checkmate, wd-40 spray (400 ml), make- pidilite, brasso (500 ml), puf spray pu foam insulation sealent (750gram), make- abro, roll guard grease, make: j.d jones (per kg), grease unirex n-3, make- mobil (per kg), gadus grease s2 v 100 3, make- sheel (per kg), bearing retainer 660, thread seal 542, fevicol sh (per kg), cold galvansing compound (6017) pure zink undercoating, make- twin tech india pvt ltd., feviquick 50 ml, cotton waste (kg.), marking cloth (mtr.), filter cloth, coton cloth (canvas), size-48 (per mtr), old dhoti, heavy duty forged steel u-clamp (pcs), steel wire brush (pcs.), painting brush size 2 ashoka make, painting brush size 3 ashoka make, painting brush size 4 ashoka make, painting brush size 5 ashoka make, painting brush size 6 ashoka make, steel lock, size-65mm , make- harison, aldrops with accessories, size-12 , material-steel, chargeble led torch 6 to 8 , teflon tape, make- champion, grease gun 2 kg., grease gun 5 kg., grease gun 10 kg., power master make tube expander with main drill shaft and ratchet handle complete set size 45mm, power master make tube expander with main drill shaft and ratchet handle complete set size 90mm, vibration meter, (pcs.), ultrasonic thickness tester (set), measuring tape 3 mtr., make-hi-wide (pcs.), measuring tape 5 mtr., make-hi-wide (pcs.), measuring tape 10 mtr., make-hi-wide (pcs.), measuring tape, 13mm fiberglass water proof, 50 mtr, make- freemans, measuring tape, 13mm fiberglass water proof, 100 mtr, make- freemans, grinder ag-4, make: bosch, grinder ag-7, make: bosch, impact wrench model gds 18e, make: bosch, walkie talkie model-tk3501 make: kenwood (license free), temperature gun, range: 0-2000c, make- fluke, temperature gun, range: 0-5500c, make- fluke, ss paint air spray gun, master level +0.02mm accuracy, size-6 , make- mitutoyo/rsk japan, dial test indicator with magnetic stand, 50mm, make- mitutoyo., shore-a digital rubber hardness durometer (din-53-505,aspm-d,2240) (pcs.), make- eco-sr, drill machine 0 to 10mm make bosch, lead wire 0.5mm (per roll rate required), lead wire 0.7mm (per roll rate required), zig zag clamp, size-3/4 , tube expender with main drill shaft with ratchet handle complete set, make: power master, car washing pressure pump heavy duty, working pressure 125 bar with 40 mtr extra pipe.(jet pump), make: bosch, electronic type weighing scale, range-0.01mg to 100gm, electronic weighing scale suitable upto 2kg, electronic weighing machine, size-600x600mm, cap-200 kg, electronic weighing machine, size-400x400mm, cap-100 kg, electronic weighing machine, size-400x400mm, cap-50 kg, straight shank bit/tapper shank drill bit/ tap set, make- miranda, heavy duty impact socket with hole 19mm for impact wrenach, heavy duty impact socket with hole 30mm(suitable for 1 inch square) for impact wrench, heavy duty impact socket with hole 32mm(suitable for 1 inch square) for impact wrench, heavy duty impact socket with hole 34mm(suitable for 1 inch square) for impact wrench, heavy duty impact socket with hole 46mm(suitable for 1 inch square) for impact wrench, sa-46 steel socket set, make- taparia, tool goti 34 no., air blower, make- bosch, hot air blower 1500 watt bajaj make (room heat

CTN :45333091

16 Jun, 2026 176

Visakhapatnam - Andhra Pradesh

Tender For tender for supply of actuator (8690610003 , 0010612100) , speed sensor , instrument , terminal , deep groove ball bear. , gasket(136l50004-1) , ring supporting , bolt , tachometer , pressure monitor 1.5 bar , plug-in board , plug in board cob9-01/a , plug-in board mob 2-01 , plug in board mpu28-02 , electronic governor ecu4 , temperature sensor pt100/110mm , coolant level sensor , module cob 8-01 , torque wrench 1-12 nm , pressure sensor , mcu 1-04 computer , indicator 30-0-30 sw-ws 96x48 , pressure sensor , pressure sensor , terminal , plug-in-board not adjusted , computer mpc 2-02 prog a.744832 , plug-in board , plug-in board sab 1-03(5295308912) , pressure sensor 6 bar(sw) , display dis 10-01(5105381275/s0004) , pressure monitor 2.2 bar , plug in board cib 3-10 , centrifugal oil filter , turbocharger , rubber bellow , nut m10 , o ring , hose , o ring , bellows rubber 125 dn 210 bolt circle , sealing ring , ce ring , washer a cop , cooler core , cooler core , o ring , cylinder head gasket , washer a cop , pressure hose , injection pump 8 cyl , buffer , control lever (s/s b00e50203122) , input device f. analogue signals , ink cartridge colour yellow , computer not adjusted , position switch , valve spring outer , switch e-stop45mm w/self monitorngco , o-ring , gasket kit (8690920032) , plug-in board , swing foll , suction chamber gasket , nozzle valve , cooper profile , rubber ring , plug in board bob 1-02 , loctite nr 510 surface sealant , manifold , rocker arm exhaust , fuel press line , multi led t.5k24 red , multi led t5.5 k24 gn , multi led t5.5 k24 yellow , horn f/pan 3 , keyboard english , leak off fuel gasket , filter strainer , thermal actuator , switch , banjo bolt , display dis 5-01 , cover , plug in board bob 1-02 a , o-ring

CTN :45318187

15 Jun, 2026 NA

Tawang - Arunachal Pradesh

Tender For supply of self recording rain gauge , maximun minimum thermometer digital , screw gauge , prismatic compass with stand , auto dumpy level with stand and staff , abney level , robotic total station 1 inch accuracy bluetooth auto target , kerosene or gas stove or electric hot plate , ghat tracer , pegging rod , optical square 90 degree , ranging rod 3 mtr long , high precision binacular , temperature gun for checking bituminous surface works , sample tray enamelled , vibrating wire , termperature sensor , portable indicator , steel tape 5m , standard pyconometer of 50 ml , digital hygrometer , post hole auger with extensions , rodo meter - high precision wheel odometer , hot plates 200 mm dia 1500 watt voltage 220v to 230v , circular plates of 250 mm dia , sampling pipettes fitted with pressure and suction inlets, 10 ml capacity. , sampling tins with lids 100 mm dia x 75 mm ht 500 gms capacity , electronic digital micrometer , ennore standard sand 25 kgs bag , weighing machine 0 kg to 10 kgs , mould 15cmx15cmx15cm for compressive strength of concrete , digital vernier calipers accuracy 0.001 mm , thermometers mercuryinglass thermometer 0 to 250 c mercury-in-steel , glass thermometers range 0 degree c to 100 degree c 100 degree c , mortar cube 70 pt 6 mm , cbr plunger with settlement dial gauge holder , ring and ball app for softening point , specific gravity test bottle with vaccum pump , tripod stands for holding dial gauge holder , metallic laboratory thermometers range up to 300 c , spacers disc 148 mm dia 47.7 mm ht. with handle , comprising beakers capacity 1000 ml glassware , pipettes capacity 50 ml glassware , perforated plate brass , metallic thermometers range up to 300degree c 300 degree c , specific gravity and water absorption testing machine , marshall sample mould , stop watch one and half sec. accuracy , field density apparutus complete setsand relacment method , compaction test equipment both 2.5 kg and 4.5 kg rammers , cbr moulds 150 mm dia -175 mm ht. , 150 mm x 300 mm ht. cylinder with capping component , riffle box , soaking tank for accommodating 6 cbr moulds , speedy moisture meter complete with chemicals , standard measures of 30, 15 and 3 litres capacity alongwith standard tamping rod , distant reading thermometer 0 degree c 250 degree c , sand pouring cylinder with conical funnel and tap and complete , gi seive set 125,90,75, 63,53,45,37.5, 14, 13.2,12.5,11.2,10,9.5,5.6,4.75mm , water still 20 ltr capacity , glass beakers borosilicate 4 nos of 100 cc, 200 cc, 500cc, 1000cc capacity , pentrometer with standard needles , platform balance 300 kg capacity , drying ovens. thermostatically controlled 100 degree c to 110 degree , water bath electrically operated and thermostatically controlled , dial gauge 25 mm travel -0.01 mm or division , aiv testing apparatus complete set , is sieve sets 450 mm internal dia with lid and pan 30 sieves in 1 set , sieves 450 mm internal dia of sieve sets as per bis of required sieve sizes , is brass sieve sets 200 mm internal dia with lid and pan 35 sieves in 1 set , sieves 200 mm consisting of sieve set of required sieve sizes with lid and pan , is sieve 75,53,45,22.4,11.22 6.5,9.50,5.6,4.75,2.36,1.18mm , soxhlet extraction or centrifuge type apparatus , oven electrically operated, thermostatically controlled including thermometer , sieve shaker capable of shaking 200 mm operated with time switch , weight machine 30 kg electronic type , high frequency mortar cube vibrator for cement testing , specific gravity apparatus , rapid moisture meter is 12175 1987 , flash and fire point apparatus , ductility testing apparatus electrically operated , density testing machine complete set bucket method , rebound hammer concrete testing hammer , furol viscometer , sand equivalent test apparatus , standard sand for density test , lab cbr testing equipment for conducting cbr testing 5 tonne cap , unconfined compression test appratus , marshal stability test machine , los-angeles abrasion te

Central Government/Public Sector

CTN :45184230

03 Jun, 2026 NA

Jhansi - Uttar Pradesh

Tender For supply of electronic water level indicator cum alarm switch. as per dlw specification no. del/spn/208. r-2 and drg.no. el/pt/0572, r-5 style -1. [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45174697

20 May, 2026 NA

Multi City - Tamil Nadu

Tender For auction sale of depot non ferrous scrap - p.l. no. 98230025. aluminium scrap consisting of condemned and unserviceable bkbl fans,bmbc dome covers, fip / sump door / tappet covers, panel boards, armature fans, impellers , blowers, fuel oil level gauges , heat sinks , bmbc dome covers, emd strainer, wiper assembly,emd stainer, temperature sensor controller, a9 / sa9 valves, steel cap pistons, pistons , cylinders, pressure guage parts ,head light frame ,portable grinding machine parts, route indicator , heating compressor gear box, side indicator , wiper motor ,horn bell,governor base, turbo impellar,magnetic valve, master contorller coupler , buzzer cover ,steel capped piston, flasher light unit , double side door closer, old hydraulic door closer , choke box , earthing device housing with cover, m.u i.v coupler housing , marker light old light housing , parts of silient gnerators set , motor / auxillary generator covers and similar diesel loco / carriage items aluminium in nature with / without ferrous / rubber /steel/ very meagre quantity of brass/copper attachments. as is where is condition. segregation and removal of attachments not permitted. note:- cssd/goc electronic weigh bridge to be used for weighment.

Central Government/Public Sector

CTN :44823166

07 May, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For bid to ras corrigendum : supply of electronic water level indicator : : - vz9700002691_ewli along with spares for unit 7 , vz9700002691_ewli along with spares for unit 8 , vz9700002691_ewli along with spares for unit 9 , 3000004555_installation and commissioning _unit 7 , 3000004555_installation and commissioning _unit 8 , 3000004555_installation and commissioning _unit 9

CTN :44875973

11 May, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : tender for supply of snep nut , joint , joint , joint d116/76x1.2t reinz-s.s , joint d172/116x1.2t reinz ss , gasket , gasket , safety valve , driving pinion , driving pinion , seal bearing housing , dearation t.b outlet connection , o ring , flexmaster conn (pipe-60.3mm-od) , hydraulic governor woodward pga12 , sensor md2r-ck-80-18x1.5-90-0.6-f2c , sensor md2r-ck-80-18x1.5-90-18.f2d , exhaust manifold std section lagged , end section t.b.side , clamping collar , clamp , exhaust manifold with diaphragm for cyl.b8 , o ring , o ring , joint , joint , addesive super cya no.495 , sensor for bearing temp , thermostat element 35/42 deg c , seal kit 35/42 deg c , air cooler outlet conn.hose , fuel pump inlet conn. , fuel leak conn.from ss valve , level switch overflow conn. , fuel feed pump discharge conn. , ss valve air inlet conn. , starting air conn.inlet , connection for pre lub oil suction , connection for pre lub oil pump , engine inlet pressure connection , fresh water air cooler inlet connection , intake pressure connection , by pass valve closing control connection , pressure gauge 80 dia 0 to 4 bars , pressure gauge 0-6 bars , pr. switch , 4140-c-k-1-e-21-aa0 , 2.7b , pr. switch , 4140-c-k-1-e-22-aa0 , 4.1b , pr. switch , 4140-c-k-1-e-22-aa0 , 4.6b , pressure transmitter p5r-6bar-4-20-1/2-pe , pressure transmitter p5r 0-40 bar , indicator temperature , mss module 0-100deg.c 4-20 temp conv. , temperature indicator q72-240 , 100deg.c , shaft speed indicator , solenoid valve (nomo-24 vdc) , capillary thermometer 100mm dial 150deg. c , pneu p.b. pneu return red , fuel rack converter , press.gauge 0-10 bar , crankcase pressure measurement assly , fuel filter , connecting straub metal grip d42.4 epdm , gasket , injection pipe , pinion on crankshaft , bearing shell , drive for barring gear , rubber compensator g0200 x 130 x 016 hks-g nbr gr deb , joint , filter regulator , silencer pads (fx4000) , time delay relay(on delay) , illuminated blue push button 2no , fuse 10x38 6a gg , solenoid valve-24v , 2 lips oil seal , bearing , o ring , o ring - kalrez , inlet valve guide , exhaust valve guide , gasket exhaust manifod , inner spring , outer spring , piston ring - top - chrome , ceramique , piston ring - compression-g3-chrome , seal , temp sensor , resilient mounts , fan+grille , selector switch 2 positions ino , selector switch 2 positions withdrawal from 3no , manometer 0-10 bar , flashing light , hooter (electronic) , power switch , bi polary fuse holder , fuse 10x38 2a gg , relay , pt 100 converter with two threshold , gal vanic insulator , solenoid valve-safety stop , pressure switch , atp thresholds temperature card , aip , human machine interface

Central Government/Public Sector

CTN :45037677

06 May, 2026 NA

Jhansi - Uttar Pradesh

Tender For supply of electronic water level indicator cum alarm switch. as per dlw specification no. del/spn/208. r-2 and drg.no. el/pt/0572, r-5 style -1. [ warranty period: 30 months after the date of delivery ]

Hydro Meteorological Information System Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector