Latest ignition system Tenders | Government ignition system Tenders

CTN :45693900

10 Jul, 2026 NA

Mumbai - Maharashtra

Tender For supply and installation of automobile trainers and equipment at consignee locations. (tender ref no.26008/2026-27) - light motor vehicle driving simulator, injector -multi hole type, pintle type, petrol engine - 2 stroke, motor cycle/ scooter, injector cleaning unit, injector testing set (hand tester), fuel feed pump for diesel, fuel injection pump - diesel - inline, fuel injection pump - dismantling tool kit, fuel injection pump - distributor fuel rotary pump with standard accessories, fuel injection pump - ve pump with standard accessories, cylinder liner- dry & wet liner, cylinder liner - press fit & slide fit, steering assembly - rack and pinion, air brake trainer assembly, alternator assembly - lmv, engine bearing model set, piston model set, front axle assembly, rzeeppa joint with stand for dismantling and assembly, full floating axle and semi floating axle assembly, wiper motor assembly, cut section model - 4 cylinder diesel engine, cut section model - automatic transmission gear box, cut section model - centrifugal clutch assembly, cut section model - diaphragm clutch assembly, cut section model - radiator - cross flow, cut section model - radiator - down flow, cut section model - shock absorbers, cut section model - single plate clutch assembly, cut section model - turbocharger, demonstration board - anti theft device car, automotive safety air bag simulator, car air conditioner trainer, demonstration board - crdi system, demonstration board - electronic ignition system and ignition coil, disk brake trainer, drum brake trainer, working model - power windows, working model - torque converter, denting kit set, engine compression tester (diesel), two post car lift- capacity 4 ton, electric operated, radiator pressure tester, tyre changer machine, tyre air pressure gauge with holding nipple, wheel alignment machince computerized 3d, wheel balancing machine (for wheel balancing of lmv), air conditioning service unit - car, automotive battery charger, automotive battery tester/ analyser, battery terminal cleaner tool, air blow gun, air impact wrench with impact sockets, engineers stethoscope, grease gun - 500 grams, oil can 500 ml, oil filter wrench - upto 500 mm, piston ring compressor - 50 - 100 mm, piston ring expander and remover - 50 - 100 mm, piston ring groove cleaner, belt tensioner gauge, car jet washer with standard accessories, auto electrical work bench, gloves: rubber, gloves: cotton, industrial/ safety shoes, industrial helmet, blow lamp: 0.5 liter, magnifying glass: 75 mm, lifting tackle/ sling: 1 ton, 2 meters, laser distance measuring instrument, demonstration board: electric vehicle cooling system, engine and transmission system for electric vehicle, cut section of electric vehicle motors, hvac trainer, electric vehicle service equipment test adapter kit, battery tester with inbuilt printer, lighting and wiring system for electric vehicle, electric vehicle diagnostic scanner, solar based charging system, electric vehicle tool kit, electrically insulating blanket, clamps for insulating blanket, insulated rubber mats, gloves: electrically insulated, industrial/ safety shoes: electrically insulated, glove inflator kit, goggle: white glass, ac current digital clamp meter, digital continuity tester, soldering iron set: mechanic electric vehicle

State Government

CTN :45676536

06 Jul, 2026 4.85 Lacs

Anuppur - Madhya Pradesh

Tender For supply of spares for hea ignition system for 210 mw atps mppgcl, chachai- heai complete system, spark road assembly

Central Government/Public Sector

CTN :45688735

16 Jul, 2026 NA

Goa - Goa

Tender For supply of fire fighting items - coat for fire proximity suit large as per encl , coat for fire proximity suit medium a s per encl , coat for fire proximity suit small as per encl , trouser for fire proximity suit large as per encl , trouser for fire proximity suit medium as per encl , trouser for fire proximity suit small as per encl , boot for fire proximity suit large as per encl , boot for fire proximity suit medium as per encl , boot for fire proximity suit small as per encl , gloves for fire proximity suit large as per encl , gloves for fire proximity suit medium as per encl , gloves for fire proximity suit small as per encl , hood inner for fire proximity suit as per encl , helmet with shroud visor for fire prox suit as per encl , dividing breaching as per encl , coupling double female as per encl , lug for coupling double female as per encl , spring for coupling double female as per encl , washer for coupling double female as per encl , coupling double male as per encl , extinguisher fire co2 2 kg squeeze grip typ as per encl , discharge horn for extinguisher fire co2 2 kg as per encl , hose for extinguisher fire co2 2 kg as per encl , 09 kg dcp extinguisher abc type as per encl , hose for 09 kg dcp extinguisher as per encl , trigger cont nozzle for 09 kg dcp extinguisher as per encl , washer for 09 kg dcp extinguisher abc type as per encl , co2 cartridge for 09kg dcp extinguisher abc as per encl , abc dry powder 10kg bag for 09kg dcp extinguish as per encl , extinguisher dry powder 75 kg trol mount ext as per encl , pvc nylon braid hose for extinguisr dry powder as per encl , nozzle for extinguisr dry powder 75kg as per encl , washer for extinguisr dry powder 75kg as per encl , discharge valv for extinguisr dry powder 75kg as per encl , 9 litre afff extinguisher as per encl , co2 cartridge 60gm for 9litre afff extinguishr as per encl , 08 mm dia 1 m length pvc nylon braided hose as per encl , nozzle for 9 litre afff extinguisher as per encl , washer for cap for 9 litre afff extinguisher as per encl , spring for 9 litre afff extinguisher as per encl , extinguisher twin 6.5 kg co2 porta trol mk ii as per encl , hose for extinguisher twin 6.5 kg co2 as per encl , nozzle for extinguisher twin 6.5 kg co2 as per encl , discharge horn for extinguisher twin 6.5kg co2 as per encl , foam liquid afff 20 ltr plastic container as per encl , fire coat medium for fire fighter suit as per encl , fire coat small for fire fighter suit as per encl , trouser medium for fire fighter suit as per encl , trouser small for fire fighter suit as per encl , rubber boots for fire fighter suit size 9 as per encl , rubber boots for fire fighter suit size 8 as per encl , gloves for fire fighter as per encl , antiflash hood for fire fighters as per encl , helmet with head lamp for ff and dc as per encl , fb 10 x foam making branch pipe , inline foam induc pick up assly for fb 10 x as per encl , fb 5 x foam making bran pipe with assly as per encl , hose impermable with instantaneous coupling as per encl , battery aa alkaline 1.5v lr 6 as per encl , variable delievery nozzlev as per encl , hose impermable with instantaneous coupling 38mm dia x 15 m

CTN :45672362

10 Jul, 2026 16.57 Lacs

Muzaffarnagar - Uttar Pradesh

Tender For erection and fabrication work a c c - mill mein lage scraper hetu discharge chute ke jo bhag kamzor evam kat gaye hain. unhe kaatkar hatana tatha nai 12 mm ki plate se taiyar kar punah sthapit karna. sath hi scraper ko baandhne hetu profile ke anusar hole wali plate lagakar/welding karke fix karna evam karya poorn hone ke pashchat trial dena. , cane carrier ke gale/ghise runner base ko kaat kar hatana. 100 mm ke channel se box banakar runner base ko lagana evam fit karna va purane channel ko nikal kar seedha karke palat kar lagana. , cane unloader ke purane ghise/kate 40/50 mm size ke sq. bar ko kaat kar hatana tatha yathasthan poorv ki bhanti naye sq. bar ko lagana evam santoshjanak trial dena. , cane carrier/rake carrier/bagasse elevator/r.b.c. ke ghise/kate runner ko kaatkar hatana. uske sthan par purane ko palat kar athva naye runner ko poorvanusar lagana. , cane carrier/rake carrier/r.b.c. ityadi chains ke side ki kati/ghisi/kamzor plate ko kaatkar hatana. uske sthan par purani athva nai plate ko lagana. , fibrizer hood ki side ki ghisi/kamzor plates ko kaatkar nikalna tatha yathasthan nai plate ko lagakar andar va bahar se welding kar santoshjanak trial dena. , bagasse baling machine ki sampoorn overhauling. testing evam trial dena. , s.r.c./i.r.c. ki purani racks ki vanchhit marammat karna. , bagasse elevator/r.b.c. ki chains ki nai racks sample anusar taiyar karna. , t.r.p.f. ke gale/kamzor bottom/top cover ko badalne ke liye naye cover poorvanusar banakar lagana evam santoshjanak trial dena. , s.r.c./i.r.c. ke gale/kamzor tail end boots ko kaatkar hatana tatha sample anusar 8.0/10.0 mm moti purani/nai plate se taiyar kar lagana evam leak.proof welding kar santoshjanak trial dena. , cane unloaders ke panjon ke vibhinn parts ko dismantle karna. dismantle kiye gaye grabs ke sabhi parts ki vanchhit marammat karna. fingers par nirdeshanusar hardfacing kar panjon ka punah assembly karna. , mills ke compound imbibition hetu lagi juice tray mein se gali/kamzor juice tray ko kaatkar hatana. nai plate se sample anusar taiyar kar yathasthan lagana evam samast connection karna. , cane carrier/s.r.c./i.r.c. tatha bagasse elevator chains ko upar uthne se rokne ke liye lagi hui guides mein se ghisi/kamzor guides ko kaatkar hatana. nirdeshanusar nai guide taiyar kar yathasthan lagakar santoshjanak trial dena. , cane unloaders ke bridge/trolley drive ke ghise/kate wheels ko nirdeshanusar welding karna. , t.r.p.f. ke gale/kamzor donali chutes ko kaatkar hatana tatha purane anusar naye donali chute fabricate kar yathasthan erection karna. , cane carrier ke liye lagi idler wheel par nirdeshanusar m.s. ke ring fabricate kar lagana. , mill head stock evam t.r.p.f. head stock ke beech nirdeshanusar 25.0 mm plate se support banakar lagana. , fibrizer ke purane hammer shanks ko nirdeshanusar welding evam hardfacing kar marammat karna evam balance karna. , cane chopper/leveller ke gale hue/kamzor hoods ko kaatkar hatana tatha nai plate se naya folding type banakar lagana. , fibrizer ke pocketed type anvil plate ki pockets ki tooti plates ko nai plates se badalna. mudi hui plates ko seedha karna tatha welding kar taiyar karke nirdeshanusar hardfacing karna. , cane leveller/chopper ke rotor assembly ki ghisi hubbo ke working side evam top sides ko welding kar samatal karna evam nirdeshanusar hardfacing karna. , cane unloaders par lage reduction gear evam motors ke kamzor beds ko kaatkar naye modify karke naye bed banakar lagana tatha gear evam motor ka alignment kar trial dena. , cane carrier ki structure ke gale/kamzor columns ko nirdeshanusar plate lagakar welding kar majbooti pradan karna. , mill rollers mein sample anusar juice ring fabricate kar fit karna. , t.r.p.f. evam mill ke beech mein lage pressure chutes ki vanchhit marammat karna. , mills ke gale/kamzor juice receiving tank ko kaatkar hatana. 8.0/10.0 mm moti plate se sample anusar tank fabricate kar yathasthan fit karna evam samast connection kar leak.proof trial dena. , mill ke ju

CTN :45657439

09 Jul, 2026 90.0 Thousand

Ghatampur - Uttar Pradesh

Tender For supply of rubber bush , brass lined rubber bush , suspension rubber buffer , hydraulic o ring for mill hydraulic , mill hydraulic rubber socket , flate ring for mill hydraulic , rubber channel , exhaust valve rubber seat , rubber seat for pan discharge , rubber seat , neoprime rubber seat , neoprime rubber mud seal , neoprime rubber u buffer , rubber bucket for pugmill , rubber bucket for hood cylinder , rubber bucket for brake cylinder , rubber bucket for brake cylinder , pneumatic valve rubber bucket , rubber stup for juice heater , expansion joint , neoprim rubber , neoprime rubber shee , rubber pad

Central Government/Public Sector

CTN :45550700

30 Jun, 2026 NA

Uttara Kannada - Karnataka

Tender For supply of carbide tipped blade chain saw - conforming standards for the item - en/din/us/equivalent standards, type of engine- 2 stroke petrol driven air cooled, displacement-79 cc, output power - 5.5 hp, engine speed at no load - 10500 rpm, type of fuel - petrol, fuel tank capacity - 0.7l, ignition system should be electronic with preferably one button start up, fully automatic and adjustable chain lubrication system, automatic chain brake system for quick stoppage when required, air filteration system for petrol engine, type of blade - carbide tipped blade, length of guard bar- 16 inch (one piece construction), adjustable depth of cut ? 6 inch, full blade guard with adjustable depth limiter in inches - 8 (minimum 1 cm adjustment), chain speed- 25 meter per second, adjustable depth of cut - 06 inch, weight of carbide tipped chain saw- 6.3 kg, cutting chain detail- carbide tipped chain with 3/8 pitch with heavy duty tie straps and tempered rivets, protective carry case should be supplied with the machine, copies of test certificates and certifications as applicable to be furnished to buyer on demand at time of supplies, demonstration of equipment and training to be provided after completing supplies,make: makita-ea7900p45e/ hikoki/ dewalt, warranty- 03 years (oem). ]

CTN :45384476

17 Jun, 2026 NA

Dharmapuri - Tamil Nadu

Tender For corrigendum : purchase of equipments for mechanical department - purchase of equipments for mechanical department, tail stock assembly medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, working model of fuel supply system - petrol mpfi type petrol multi point fuel injection (mpfi) system for dismantling and assembly practice system type: non-working / cut-section model for study of internal construction construction: actual automotive components or equivalent training model mounted on frame includes throttle body (sectioned), fuel injectors, fuel rail, intake manifold includes fuel pump, fuel tank (dummy), fuel filter, pressure regulator includes ignition system components: ignition coil, spark plug, distributor (if applicable) ecu module (dummy/display type) with wiring layout representation all components cut-open, painted, and clearly labelled provision for manual demonstration of flow path and component interaction mounted on rigid ms powder-coated frame designed for repeated dismantling, assembly, and component identification, hydraulic cylinderbore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply: mounted on training base suitable for dismantling and inspection, hydraulic operated directional control valves (dcv) type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study, bearing with shaft assembly type: dismantling and assembly teaching unit shaft diameter: 30 mm shaft material: en8 steel bearings: deep groove ball bearing (6205 / 6206) housing: cast iron locking arrangement: circlips end covers mounting: bench-mounted / frame mounted unit, coupling unit using driving and driven shafts using plummer block bearing unit the plummer block housing material: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing). sealing: felt seals or v-ring seals (to demonstrate lubrication retention). lubrication: provided with a grease nipple at the top center for manual lubrication practice. the bearing type: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series). bore diameter: standard 25mm or 30 mm. shafting and coupling shaft material: ground carbon steel (en8 or en9) for high surface finish. coupling type: flexible coupling: to demonstrate the bearings ability to handle slight misalignment. rigid flange coupling: to demonstrate traditional direct connection. driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., 3d printing machine build volume(wxdxh) 256 x 256 x 256 mm shell enclosed (plastic & glass) hot end all-metal nozzle 0.4 mm stainless steel included max hot end temperature 300 nozzle diameter 0.4 mm (included) 0.2 mm, 0.6 mm, 0.8 mm build plate compatibility textured pei plate, cool plate, engineering plate, high temperature plate max build plate temperature 100 max speed of tool head 500 mm/s max acceleration of tool head 20 m/s supported filament pla, petg, tpu, pva, pet, abs, asa chamber monitoring camera low rate camera 1280 x 720/0.5fps time lapse supported filament run out sensor :yes control board fan closed loop control auxiliary part cooling fan closed loop control air filter activated carbon filter

CTN :45090186

18 Jun, 2026 NA

Multi City - Andhra Pradesh

Tender For corrigendum : procurement of spares for hea ignition system

CTN :45435017

18 Jun, 2026 4.00 Lacs

Thanjavur - Tamil Nadu

Tender For supply of mechanical lab items - furniture, crdi system demonstration board working with motorized. specification: fuel supply system diesel crdi type (actual working model with electronic ignition system), inlet manifold,throttle body with acceleration position sensor, fuel common rail, fuel injectors, fuel tank, fuel filter, fuel tank module (fuel pump), pressure relief valve, pressure gauge, ecu, electronic delco with distributor (powered by 12v motor or camshaft), ignition coil, spark plugs, power supply 12v / 10 amps, fuel level gauge & control panel,ignition key for on/off system, mpfi system demonstration board working with motorized. specification: fuel supply system petrol mpfi type (actual working model with electronic ignition system), inlet manifold,throttle body with acceleration position sensor, fuel common rail, fuel injectors, fuel tank, fuel filter, fuel tank module (fuel pump), pressure relief valve, pressure gauge, ecu, electronic delco with distributor (powered by 12v motor or camshaft), ignition coil, spark plugs, power supply 12v / 10 amps, fuel level gauge & control panel,ignition key for on/off system, exhaust gas analyser specification: to find the percentage of co, co2, o2 and amount of hc, nox in exhaust gas. *operating temperature: 0 to 50 degree celcius*measuring gas intake ; 1 litre per minute*reposnse time : 5 sec

CTN :45029430

11 Jun, 2026 3.53 Lacs

Ganganagar - Rajasthan

Tender For corrigendum : repairing of hea ignition system, power supply and calibration probe for ssctps, suratgarh

Ignition System Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government/Public Sector

Central Government/Public Sector