Latest injector sleeve Tenders | Government injector sleeve Tenders

State Government

CTN :43467490

13 Jan, 2026 NA

Delhi - Delhi

Tender For s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government / Public Sector

CTN :43502224

22 Jan, 2026 NA

Sultanpur - Uttar Pradesh

Tender For supply of oil temperature sensor , water pump assembly , oil seal flywheel side , oil seal , water level sensor , oil pressure sensor , pigtail harness , piston gudgeon pin clip , engine cylinder liner , connecting rod bearing , oil ring viton , cylinder head cover gasket , copper bush , disc washer , o ring viton , copper washer , engine wiring harness , canopy wiring harness , high pressure fuel pipe , high pressure pipe , flexible fuel pipe , o ring set , gasket set , flexible fuel pipe set , hose set , hose clip set , radiator coolant , inlet valve , exhaust valve insert , inlet valve insert , valve cone outlet , valve collet , valve spring outer , valve spring inner , valve guide , valve spring cap , injector sleeve , brass cap , injector stud bolt , lubricating oil pump , lube oil filter element , fuel filter pre , fuel filter micro , lubricating oil , lubricating oil ci 4 , air filter outer element , air filter inner element , battery , toh charges , freight charge , cylinder head calibration , fip calibration , injector calibration , turbo calibration ) /bid number : gem/2026/b/7084334 * /dated: 08-01-2026 & & / bid document 1 / 59

CTN :43483922

17 Jan, 2026 NA

Gonda - Uttar Pradesh

Tender For supply of protection sleeve , spiral sleeve 8mm , spiral sleeve 2. 5 mm , cable tie

CTN :43465273

27 Jan, 2026 NA

Mumbai - Maharashtra

Tender For tender for supply of radial-lip shft seal , oil seal , grease nipple 1 8 bsp , ball bearing deep groove , felt seal , timer 60 sec , 73a contractor , control terminals , ball bearing deep groove , led indicating light , color red , led indicating light , color yellow , led indicating light , color green , aux. contactor 2 no + 2 nc , cable sleeve , tapper pin , tapper pin , float switch , temperature sensor with oisplay unit , joystick , element for return line filter , counter balance valve , control terminals , bearing , main shaft , grease nipple (1 4 bsp) , slipping clutch cum flexible coupling , 63a tp switch , bi-metalic overload relay , pneumatic time on-delay , bridge rectifier complete , felt seal , push button with black actuator , over load relay 17.4-24a for slow speed , 6a contractor 220v ac coil (5 no+3 no) , push button (green) 1no , pump f water sanitary centrifugal horizon 10 40 with motor , pump centrifugal vertical 63 80 with motor 380v fire pump , puse button with element , grease nipple 1 8 bsp , bearing 7313b , bearing 6006 , bearing 6007 , bearing 1207 , oil seal 35x55x8 double (mi) , indicating lamp red complete , indicating lamp yellow complete , indicating lamp blue complete , auxiliary contacts for 16a contactor , coil for 16a contactor , thermister protection relay , bridge rectifier surge suppressor , push button (yellow) complete , indicating lamp(clear) complete , push button (green) complete , indicating lamp (red) complete , indicating lamp (green) complete , bearing , bearing , bearing , circlip , over load relay , over load relay with ssp independent , thermister relay 1no+1nc 1e & 2a , pilot lamp yellow lens 230v bulb , pilot lamp amber lens 24v bulb , over load relay 17.4-24a , timer on-delay , control terminal 2.5mm , motor protection relay

CTN :43452184

16 Jan, 2026 NA

Jaisalmer - Rajasthan

Tender For supply of video transmitter vtx , fpv antenna , motor wire protection sleeve , radio controller , radio receiver

CTN :43452086

15 Jan, 2026 3.00 Lacs

Ambala - Haryana

Tender For supply of r1 spares for plant equipment d d - air filter , oil filter , fuel filter , mud filter , steering filter , hyd filter , hrs meter cable , baby filter , track chain scar , jack cyl sear , terminal positive negative , hydro meter , bulb 24v , head light , txu filter , accelator cable , ignation switch , txn filter , feed pump , fuel filter cotton , tie road , accelerator cable , lifting pump , boom slider pipe , break bulb 12v , window lock handle , jack cylinder seal , wheel brace 27 and 30 , bucket teeth with nut bolt , stud , vall dia , pressure guage , jack 20 ton with rod , wheel brace 38mm , relay 12v , front axle tube oil seal , rear axle tube oil seal , break pipe , clutch cyl rep kit new model , sleeve cyl rep kit new model , gear lever rep kit major , fuel cut off switch , dual brake valve rep kit , relay 24v , front brake pipe , rear brake pipe , front hub seal , rear hub seal , front and rear hub lock washer , ram assy pipe , fuel cut off solenoid 24v , gear lever end , front brake pipe , rear brake pipe , fan belt 1250mm , system protection valve rep kit , fuse new model 5 10 15 amp , four way valve rep kit , sp valve rep kit , clutch cyl rep kit 22mm , clutch cyl rep kit 22 point 5mm , clutch cyl rep kit 25mm , clutch fluid pipe rear and front side1 9mm , hyd hose pipe 17mm , hyd hose pipe 19mm , hose pipe 24mm pnumatic pipe , hose pipe 27mm pnumatic pipe , hose pipe 32mm pnumatic pipe , anabond , thread tape , m seal , insulation tape , washer 13 17 19 22 24mm , rust cleaner , araldite , cotton tape , fuel filter , bty timble , air filter prime , air filter secen , oil presser gage , oil presser meter , bty terminal , oil filter , alternator belt ) /bid number: gem/2026/b/7068906 * /dated: 05-01-2026 & & / bid document1 / 64

CTN :43451971

20 Jan, 2026 NA

Kangra - Himachal Pradesh

Tender For supply of cord set high tension , brush carrier plate , cable assy control , tendom master cyl , system protection valve , main line switch , sleeve cyl assy

CTN :43326998

16 Jan, 2026 7.58 Lacs

Baran - Rajasthan

Tender For corrigendum : supply of spares of single screw pumps installed at etp and pt plant unit 3 and 4, ctpp, chhabra - pump casing , bearing housing , stuffing box housing , gland , hammer bolt , hex. nut , packing ring , discharge branch , helical rotor , joint shaft , drive shaft , distance bush , tension rod , stator , gasket , radial ball bearing , radial ball bearing , supporting ring , circlip for bore , circlip for shaft , radial shaft seal ring , stud bolt , hexagon nut , spring ring , hexagon nut , spring ring , screw plug , joint ring , key for coupling , identification plate , indication plate , direction of rotation , indicator , self tapping screw , self tapping screw , pump foot , grub screw , cardon joint assembly , each assy. consisting of: , joint protection sleeve , joint pin , universal joint bush , protecting bellow , circlip for shaft , joint pulley , lock washer , zyko-sleeve , locking sleeve , joint head , 'o' ring , 'o' ring , taper pin

CTN :43467332

09 Feb, 2026 NA

Gorakhpur - Uttar Pradesh

Tender For supply of kit for primary vertical dampers consists of 6 items . (1) rubber disc - 04 nos. (2)washer - 04 nos. (3) plate - 02 nos. (4) sleeve - 01 nos. (5) m 16 nyloc nut - 02 nos. (6) protection cap - 02 nos.

State Government

CTN :43164609

21 Jan, 2026 NA

Kutch - Gujarat

Tender For corrigendum : supply of various consumables & miscellaneous items at wtp, workshop & fire - store code: 4802000003 portable single phase welding machine. (light weight 10 kg), store code: 4802000004 portable three phase welding machine. (light weight 15 kg), store code: 4805000012 two stage two gauge oxygen gas pressure regulator - model no : dura 0-10 - esab make, store code: 4805000013 two stage two gauge acetylene gas pressure regulator model : dura a-1.5 - esab make, store code: 4805010301 gas cutting torch cutogen esab make, store code: 4805020016 cutting nozzle size 3/64", store code: 4850120008 black glass for welding size 82.5x107.95x3 mm, store code: 4850140006 welding helmet, store code: 4850010008 welding electrode holder fully insulated 600 amp. current (hc 600) , make-esab., store code: 4921010235 portable cut-off saw/ machine size 355 mm, hitachi, japan make model no. hu-14/kpt make model no. kc355., store code: 4937020009 kpt make 100mm angle grinder model no.p 34-01, 220/240 volts, current 2.9amp, ac 600w, 1200rpm, weight 1.9kg approx, store code: 4956200002 mpact drill machine gsb-13 re of make bosch, store code: 4956110008 and drill machine., store code: 4958000019 rcc drill bit of 12 mm dia isi make., store code: 4921100032 ag-4 cutting wheel make:bosch, store code: 4937050003 grinding disc (wheel) size 100x4x16 mm, mos 13750 high cut (a.36) ., store code: 5801060006 carborundum universal make cutting wheel of size-350x25.4x3 mm (a-24-r5-bfw), store code: 4937050113 buffing wheel , size: 100 x 16 x 5/6 mm, store code: 5812050216 smoke grey paint, store code: 5812100001 bitiminus black paint, store code: 5813030001 apcolite synthetic enemel cascade green paint, store code: 5813030108 synth enamel white paint, store code: 5812010001 becktol red paint, store code: 5815020004 thinner 101 (asian make) thinner material, store code: 5810110101 red oxide, store code: 5801200007 painting brush size 25 mm, store code: 5801200008 painting brush size 50 mm, store code: 5801200009 painting brush size 75 mm, store code: 5801200022 painting brush,size:4"(100 mm)., store code: 4850350007 nylon wire brush size:- 6mm, store code: 4850350008 nylon wire brush size:- 8mm, store code: 4850350009 nylon wire brush size:- 10mm, store code: 4850350010 nylon wire brush size:- 12mm, store code: 4850350012 nylon wire brush size:- 16mm, store code: 4971040001 tin cutter with spring size 10" confirming to is 6087 -1971, store code: 5620240134 pen oil, heavy duty rust penetrator, packing : 500ml. code: 6030 of stanvac having following properties. non acidic, non corrosive formulation, ozon friendly, make: stanvac/crc/oks., store code: 5610030046 rust remover wd 40, 400 ml / bottle, store code: 3440080003 pvc hand gloves acid/alkali proof size 16" (yelow colour), store code: 3440080065 nitrile coated hand gloves for handling of sharp object & scrap material, store code: 3440000019 3 piece pvc suit for protection against chemicals containg pant,coat and face piece with visor, store code: 3440140001 pvc apron without sleeve 24"x48", store code: 3440060002 gum boot size- 8, store code: 3440060003 gum boot size- 9, store code: 3440060004 gum bootsize- 10, store code: 5920200018 glycerine, store code: 5150950008 rubber spider (star bush) for love joy coupling l-190, store code: 6697070067 silica gel breather for transformer- capacity 15 kg., store code: 4515010089 rubber sheet-2000x1000x3 mm shore hardnesss-50 to 60, store code: 4515010090 rubber sheet 2000x1000x5 mm shore hardnesss-50 to 60, store code: 4515118181 non metallic gasket sheet thickness 1 mm suitable for oil application

Injector Sleeve Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

Central Government / Public Sector

State Government