Latest key shaft Tenders | Government key shaft Tenders

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

corporations/Associations/Others

CTN :45648129

03 Jul, 2026 NA

Puruliya - West Bengal

Tender For tender for supply of soot blower spares for rtps dvc steam nozzle tube for aph shoot blower model no.:, ahlw, tag no. ah03 &ah04 part #08136lw-007, contract no. sc08136- shanghai clyde bergemann, gear box for aph shoot blower model no.: ahlw, tag nos. ah03 & ah04 part # gb_ahlw, contract no. sc08136-shanghai clyde bergemann, chain pno-gb1243.1, roller shaft pn-ahlw/8/13, vent valve assly, all type soot blower (ps-, ll, v04, ahlw), part no-6518, gasket, vent valve for short retracting blower, model no.: v04, part # 1659, contract no. sc08136-, shanghai clyde bergemann, spring, vent valve, all type soot blower (ps-ll, v04, ahlw), part no-5304, screw tube assly (shaft assly), wall deslagger, model: v04, part no-v04-2-0, nut drive, machined, wall deslagger, model: v04, part no: v04-2-2, pin screw assly, wall deslagger, model: v04, part no: 5044, roller chain assly, wall deslagger, model: v04, part no: v04-3-4, packing of feed tube, wall deslagger, model: v04, part no: 6638, gasket of feed tube assly, wall deslagger, model: v04, part no: v04-5-3, poppet valve assly, inlet d55, all type soot blower (ps-ll, v04,ahlw), part no-25844, valve internal assly, inlet d55, all type soot blower (ps-ll, v04,ahlw), part no-7048, chain link cranked, long retract soot blower, model:ps-ll, part no-5640, chain link, long retract soot blower, model:ps-ll,part no-5648, chain, long retract soot blower, model:ps-ll, part no-1823, packing (hard), long retract soot blower, model:ps-ll, part no-13750, packing (soft), long retract soot blower, model:ps-ll,part no-5629, feed tube gasket, long retract soot blower, model:ps ll, part no-1668, lance tube gasket, long retract soot blower, model:ps-ll, part no-1678, spring-valve, valve intnl assly, feed tube assly, long retract soot blower, model:ps-ll, part no-08136ll-001, lance tube assly, t91,101.6 od(tag no.r1, r2, l1&l2), long retract soot blower, model:ps-ll, part no-08136ll-002, lance tube assly, t11, 101.6 od (tag no.r3 to r5,l3 to 15), long retract soot blower, model: ps-ll, part no-08136ll-003, lance tube assly, t11 (tag no.r11 tor22 &l11to l22), long retract soot blower, model:ps-ll, part no-08136ll-005, lance tube assly, t11(tag no. r6 to r10 &l6 to l10), long retract soot blower, model: ps-ll, part no-08136ll-004, lever / roller for limit switch make - clyde bergemann, part id: v04-11-5

State Government

CTN :45027637

30 Jun, 2026 90.66 Lacs

Umaria - Madhya Pradesh

Tender For corrigendum : procurement of spares for condensate extraction pump installed at unit no. 1 to 4, sgtps, mppgcl, birsinghpur. - spares for condensate extraction pump , model en5j40d, bhel drg no. 01811113727, sleeve for stuffing box, 1st stage impeller lock nut, 2nd stage impeller lock nut, thrust collar lock nut, shaft with all keys and nuts, stuffing box bush, coupling, spares for condensate extraction pump , model en5j-40d-30a , bhel drg no. 01811154078, bell mouth, sleeve bell mouth, bush stuffing box, sleeve stuffing box, shaft, complete thrust bearing with thrust collar, casing last stage, casing inter stage, impeller 1st stage, impeller inter stage, ring wear casing nde (inter stage), ring wear casing de (inter stage), ring wear 1st stage casing, ring wear 1st stage impeller, ring wear impeller other stage, nut shaft thrust collar, nut shaft 2nd stage, nut shaft bell mouth, key impeller 1st stage, key impeller 2nd stage, key impeller 3rd,4th, 5th stage, key shaft sleeve 1st stage, key shaft sleeve 5th stage, key thrust collar, key coupling, set of lock washers, set of fasteners (including studs, bolts, nut, screws), set of o-ring, restriction bush, coupling set assembly (both pump & motor end, including distance piece, element assembly, fasteners ), .

corporations/Associations/Others

CTN :45282579

25 Jun, 2026 NA

Bokaro - Jharkhand

Tender For corrigendum : supply of rigid coupling with shrink disk for keyless shaft hub locking for stacker reclaimer

CTN :45577473

02 Jul, 2026 3.50 Lacs

Muzaffarnagar - Uttar Pradesh

Tender For supply of on conversion basis gun metal bearing liner for transmission gear shaft bottom bearing bor 305 mm halve complete in all respect finish machine , on conversion basis gun metal bearing for top roller top halve complete in all respect finish machined , on conversion basis gun metal bearing liner for side roller halve complete in all respect finish machined , on conversion basis gun metal bearing liner for side roller halve complete in all respect finish machined. , on conversion basis gun metal bearing liner for transmission gear shaft-bottom bearing bor 250 mm halve complete in all respect finish machine

Central Government/Public Sector

CTN :45566147

30 Jun, 2026 NA

Malanjahknd - Madhya Pradesh

Tender For supply of c i body p no 1 , c i head i e p no 2 1 , c i head d e p no 2 d , s g iron rotor p no 3 , c i cone i e p no 4 1 , c i cone d e p no 4 d , en 8 shaft p no 5 , packing head and body p no 7 , packing head and cone p no 8 , bearing housing d e inner p no 9 d , bearing housing i e inner p no 9 1 , bearing cover d e outer p no 10 d , bearing cover i e outer p no 10 1 , shims or spacer p no 11 , locknut bearing p no 13 , lock washer bearing p no 14 , packing de outer and housing p no 15 , c i gland p no 16 , packing rope gland ptfe p no 17 , oil seal ie and de housing p no 18 , oil seal d e outer cover p no 18 a , key shaft pulley coupling p no 19 , slinger p no 21 , s s 304 shaft sleeve p no 22 , check ball

CTN :45513739

02 Jul, 2026 NA

Ernakulam - Kerala

Tender For supply of wearing ring , spacer sleeve , gasket , gasket , allen screw , mechanical seal , gasket , gasket , pipe nipple , hose complete , double nipple , air inlet valve , hose complete , impeller key , allen screw , air wheel key , shaft sleeve , shaft sleeve , gasket , gasket , bearing housing , grease nipple , oil seal , pump shaft , splash ring , adjusting bush , angular con bearing , inner circlip , nilos ring , nilos ring , adjusting ring , external circlip , allen bolt , impeller , wearing ging , spacer sleeve , coupling half motor side , gasket , gasket , allen screw , allen screw , dowel , hex nut , allen bolt , mechanical seal , gasket , gasket , air wheel , impeller key , allen screw , air wheel key , shaft sleeve , shaft sleeve , gasket , gasket , bearing bracket , oil seal , shaft , splash ring , adjusting bush , roller bearing , ang con bearing , inner circlip , nilos ring , nilos ring , adjusting ring , outer circlip , allen screw , allen bolt , o ring , float niddle , float , o ring , valve seat long , valve seat short , impeller

Central Government And Public Sector

CTN :45486853

22 Jun, 2026 NA

Bangalore - Karnataka

Tender For supply of helical inline gear motor to the model no. sk 973.1 - 112mp/4 tf for axle pusher chain conveyor of make m/s nord or substantially equivalent with following features: input speed(rpm): 1440; output speed(rpm): 21; gear ratio: 68.5; power (kw): 4; service factor: 1.8; output torque: 1817 nm; overhung load: 25 kn; axial load: 22 kn; motor inverter speed range: standard line powered inverter capable; voltage: 400/690 v; frequency: 50 hz; efficiency class: ie3; current 1: 7.85 a; current 2: 4.53 a; cosinus: 0.83; motor duty: s1 - continuous; enclosure: ip55; insulation class - f; mounting pos - m1; housing material: cast iron housing; type of housing: foot mount; output shaft: solid keyed shaft; output shaft (dia x length): 60x120mm; output shaft material: standard; gearbox breather options: auto vent; gearbox sealing options:fkm seals; bearing design: standard bearings; motor cooling: tefc - totally enclosed fan cooled; motor thermal protection: thermistor; motor option: fluoro rubber motor seals; height of output shaft center frombottom of base plate: 225 mm; mounting base plate details: minimum plate thickness: 50 mm; 04 holes of 22 mm dia each with square pattern; distance between holes along the shaft: 310 mm; distance between holes perpendicular to shaft: 250 mm; note: - (i) material of construction: fabricated steel housing (stress relieved) (ii) all gears shall be manufactured from steel forgings or rolled bar made from steel 17cr ni mo6/18cr ni mo6 (case hardening steel). (iii) all gears shall be case hardened to 58-62 hrc and profile ground. (iv) output shaft shall be of en 9 material normalized to 201 bhn (min) (v) bearing used shall be rolling element type of make skf/ntn/timken/fag only. special conditions: above specified materials are the minimum required standard to be considered while designing the gear motor. [ warranty period: 18 months after the date of delivery ] ]

CTN :45404122

19 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using

Co-operative

CTN :45474707

23 Jun, 2026 NA

Udhamsign Nagar - Uttarakhand

Tender For c.i. item on conversion/supply basis - c.i.pipe with standard thickness & flange as per i.s.i. specification machined from dia 4" to 12"(i) new material supply basis, (ii) on conversion basis, c.i. bend, duck foot bend, cross,tee and other such part all size as per drg.(i) new material supply basis, (ii) on conversion basis, c.i.drum, rod,bush, bari,idler pully, break drum for cane unloader etc as per drg.(i) new material supply basis, (ii) on conversion basis, c.i.coupling from 4"dia to 10"dia plane/flange type(i) new material supply basis, (ii) on conversion basis, c.i. firing frame,door side chamber, bagasse rotary chuts, rotary feeder drum , clit, hanger, beam, gutka, furnace nozzle, clam etc. and other such parts for lipi/taxmaco boiler as per different drg.high chrome grade 25 , casting & machined temp. capacity 15000 c(i) new material supply basis, (ii) on conversion basis, c.i. clamp/ hanger clit small size for lippi boiler no. 3 as per drg. blr-79 high chrome grade 25 , casting & machined temp. capacity 15000 c, c.i scapper mixed with pig iron and having standard hardness dully machined as per drg.no.mh-66 ( r)(i) new material supply basis, (ii) on conversion basis, (iii) grooving of c.i.scrapper as per drg., centrifused casted c.i.coupling for fmg gear of kcp mill od 1000 mm.pcd 815(18 holes)9+9,with machining complete as per drg.no.mh-93, c.i.motor cover for different type motor, mill setting bolt & nut for kcp mill drg.no.mh-106, mill setting bolt & nut for taxmaco mill drg.no.mh-38, c.i.worm and worm wheel for crystilizer as per drg.bh-39 ( r ) machined, c.i.worm and worm wheel for vertical crystilizer no. 2 complete set as per drg. machined, eccentric shaft and eccentric for hopper as per drg.no.bh-60, m.s.shell for under feed roller as per drg.mh-95.length 1525 mm.od 750mm,thickness 18mm, c.i. muff coupling for cane unloader as per drg.no cu-25, c.i.gear for magma mixture as per drg.no bh-137.od 450mm,no.of teeth-51.bore 70mm, width 63mm, c.i.brake drum for s.d.centrifugal machine taxmaco make duly machined(i) as per drg.no. bh 81/1, (ii) as per drg.no bh-81/2, c.i.v-belt pully of cont.centrifugal machine duly machined, c.i.scale seat for juice weighing scale duly machined and drilled as per drg.no.mh-195, id fan pully (as per drawing no. bl-r-128/2024-25), id fan motor pully (as per drawing no. bl-r-129/2024-25), boiler grate bar material-cont iron. (as per sample/drg.), boiler furnace manage gap bar. (ap per sample/drg.), chief engineer

Key Shaft Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

State Government

corporations/Associations/Others

Central Government/Public Sector

Central Government And Public Sector

Co-operative