Latest key shaft Tenders | Government key shaft Tenders

State Government

CTN :43467490

16 Jan, 2026 NA

Delhi - Delhi

Tender For corrigendum : s/i/t/c of e/m equipments and allied works for newly re-bored tube well at okhla vihar near majar in okhla constituency ac-54. - supply of submersible pump set fitted with dynamically balanced ss impeller mounted on stainless steel shaft with protection sleeve having stage bowl & closed grained shorted type impeller, the pump will be directly coupled to required wet type induction motor of 7.5 hp, 15 stage, speed 2900 rpm suitable for operation of 3 phase, 415 volt, 50 hz, ac supply with efficiency 70% at following duty point: 200-125-75 lpm on 89-124-133 mtr. head.having discharge outlet 50 mm and outside dia 142 mm.make: bs/skope/ any djb approved. , supply of hut type electrical feeder pillar / fabricated with 50 x 50 x 6mm angle iron and 16 swg ms sheet with horizontal and vertical intermediate member of suitable size. i.e. 1370 mm x 760mm x 460 mm. with arrangement for mounting of switchgear and electrical energy meter i.c. painting heaving following item fitted. a) mccb 63 amp, 4pole, 415volt, 35 ka -1 no. b) rccb 63 amp, 4pole with earth fault indication protecting a circuit automatically in the event of earth leakage sensitivity 100ma, - 1 no c) fully automatic star delta starter of relay range 13-21 amp. (7.5 hp to 10 hp) 3 phase oil immersed type -1 no.d) ampere 96 x 96 mm. square shape 0-30 amp-1 no. e) voltmeter 96 x 96 mm. square shape 0-500 volt-1 no.e) indicating lamp (a set of 3 lamps) 1.setf) shunt capacitor of 10 kvar mpp type with three phase isolator with suitable banking g) motor protection assembly with earth leakage protection phase sequence corrector, single phasing, protection, overload protection, high voltage / low voltage protection time delay power on, programmable time switch i.c. r&b phase facility to change over from automatic, to manual &vice verse for up to 10 h.p -01 nos.complete wiring &installation of above accessories with required copper conductor wire and thimble etc. 01 job.make of all components: any djb approved., s/o pvc insulated and pvc sheathed cable with plain copper conductor having 3 phases, 3 core flat for submersible motor of 4 square mm size each 100 mtrs. make:grandlay / havells./any djb approved make, s/o m.s. clamp of 600 mm length duly fabricated out of 12.5 mm thick 75 mm wide, m.s. plate for holding the pipe of 50 mm dia., s/o double flange gi column pipe 50 mm dia medium class each of 3 mtrs long duly threaded on both ends, welded fitted with gi flange on both ends with slot of submersible cable. make: tata/ jindal./any djb approved make, s/o/ tail piece of the medium class gi pipe 500 mm long with one end threaded as per outlet of pump & another end flanged as per size of gi pipe 50 mm dia., s/o gi 90 bend of size 50 mm dia having both side flange (heavy duty)., supply of ms nut bolts off size as per requirement., s/o rubber packing for 50 mm dia flange., fabrication and supply supply of bore cover approx size 1x1 made out from 6mm thick m.s. sheet in 2 halves and a circular hole in centre 3-1/2 dia. with locking arrangement by nuts and bolt. , earthing with g.i. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required., providing and fixing 6 swg dia g.i. wire on surface or in recess for loop earthing as required., installation of t/well by lowering of sub p/set with all allied above items. this includes installation and grouting of panel boards with all electrical wiring & cabling at site. all tools & tackles i/c. tripod chain pulley blocks etc. shall be arranged by the firm. this includes testing & commissioning of t/well on load at site i/c. cartage, loading & unloading of material. it also includes a trial run of 30 hrs operation successfully by the firm. all required civil work included in the scope of work.

Central Government/Public Sector

CTN :43519572

29 Jan, 2026 NA

Sonbhadra - Uttar Pradesh

Tender For supply of solid steel shaft

Central Government/Public Sector

CTN :43290429

19 Jan, 2026 86.44 Lacs

Dipka - Chhattisgarh

Tender For corrigendum : supply of procurement of spares for flowmore make pump - pump shaft part no fm5911 moc astm a 276 ss410 , key for pump half coupling part no fm5912 moc en9 , oil seal de for bearing cover outer de part no fm5913 moc nitrile rubber , counter sunk screw for st cover to suc cover part no fm59110 moc ht steel is 1367 gr 10point8 , external threaded dowel pin for st cover to suc cover part no fm59111 moc ht steel is 1367 gr 10point8 , stuffing box cover part no fm59112 moc 2point5percentage ni ci is 210 fg 260 , pipe plug for stuffing box cover part no fm59113 moc mi , wearing ring for stuffing box cover part no fm59114 moc astm a 743 ss ca 15 , o ring for st box cover to suc casing suc casing to cover plate part no fm59119 moc nitile rubber , cover plate part no fm59120 moc 2point5percentage ni ci is 210 fg 260 , counter sunk screw for cover plate to suc cover part no fm59121 moc ht steel is 1367 gr 10point8 , external threaded dowel pin for st cover to suc cover part no fm59122 moc ss316 , counter sunk screw for partition plate to suc cover part no fm59123 moc ht steel is 1367 gr 10point8 , partition plate part no fm59124 moc 2point5percentage ni ci is 210 fg 260 , external threaded dowel pin for partition plate to diffuser part no fm59125 moc ss316 , diffuser part no fm59127 moc 2point5percentage ni ci is 210 fg 260 , external threaded dowel pin stage to delivery diffuser part no fm59130 moc ss316 , large seating bush for del cover part no fm59136 moc bronze is 318 ltb 5 , counter sunk screw ls bush to del casing part no fm59137 moc ht steel is 1367 gr 10point8 , balance valve part no fm59138 moc bronze is 318 ltb 2 , sleeve nut two no rh 2 no lh thread part no fm59145 moc steel , shaft sleeve nde at balance valve cover part no fm59146 moc astm a 276 ss410 h , key for suction impellor balance valve part no fm59152 moc en9 , key shaft for stage impellor both end round part no fm59153 moc en9 , neck bush diffuser part no fm59154 moc bronze is 318 ltb 5 , wearing ring for st stage partition plate part no fm59155 moc astm a743 ss ca15 , shaft sleeve imp to imp part no fm59156 moc astm a 276 ss410 h , case spacer bushing for cover plate part no fm59157 moc bronze is 318 ltb 5 , water seal ring part no fm59159 moc bronze is 318 ltb 2 , split gland part no fm59161 moc 2point5percentage ni ci is 210 fg 260 , dowel pin for gland part no fm59162 moc en9 , o ring for shaft sleeve part no fm59163 moc nitrile rubber , shaft sleeve de part no fm59164 moc astm a 276 ss410 h , pipe plug for air seal dran filling part no fm59172 moc mi , impeller single suction for second stage part no fm59129 moc astm a 743 ss ca 6nm

Corporations And Associations And Others

CTN :43499288

15 Jan, 2026 2.98 Lacs

Delhi - Delhi

Tender For supply of machinery/tools for various parks at sarita vihar in ward no. 187, central zone - brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cutting attachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight( dry,without cutting attachment & deflector): should not be more than 7.5 kgclutch: centrifugal type, clutch shoe support base & lining metal only.multi function handle: should have acceleration ,on/off switch at right handle.brushcutter harness: should be double shoulder harness only.anti vibration system: must have 4- point aniti vibration system.vibration level in m/s2 at right handle : should not be more than 2.5 m/s2sound pressure level db(a): should not be more than 105 db(a)drive shaft design: must have drive shaft ends square design type only.certification : must have valid en certificaton, petrol operated chain sawengine : single cylinder, 2 stroke, aircooled onlydisplacement: 45.4ccpower output : 2.3kw. 3.0 hp max.engine speed (with guide bar & chain ): at least 12500 rpmcarburetor: diaphragm type & compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight( without cutting attachment ): should not be more than 5.0 kgclutch: clutch shoe linining metal only.guide bar design: should be rollomatic type.guide bar length: guide bar length must have 50 cm/20" inch. guide bar and chain: should have same manufacture only.chain type: every drive link require groove & small oil receiver hole for better lubrication. 0.325 inch pitch & 1.6 mm thickness only.chain lubrication system: fully automatic ,speed controlled rotary oil pumpchain oil tank capacity: should be minimum 200 ml.oil pump drive: should have direct drive from crankshaft & oil pump flow adjustable.master lever control: must have all operation in one hand, chock,throttle, acceleration,switch off.guaranteed sound power level: should not be more than115 db(a)maximum chain velocity to iso 11681: should be minimum 28 m/scertification: product should have valid dplf certificate with test standard en iso 11681., tree prunersupply of telescopic pole pruner:-specification:- pole length incuding blade: 6.5m blade material: hardened & tempered high carbon steel .the head of the blade shall have a hooked tip useful for cutting twigs saw blade shape: hooked type curved saw blade type & no of cutting teeth :tripple grounded 86 teeth blade length : 15"-16" pole type: light weight telescopic tubular aluminium alloy extendable pole no of positions for pole height adjustment : 10 positions locking mechanism : ergonomicvally designed two way locking mechanism total working length : max 219"(6623 mm), min 103" (3103mm) branch cutting capacity: 200mm max, lawn mowersupply of lawn mower:-specification:- type of machine walk behind lawn mowerspower source petrol enginestart type recoil / pull startspeed control variable speeddrive type all wheel driveblade style rotary typeblade engagement electromagneticcut width (mm) 500 to 524minimum cut height 1 millimetermaximum cut height 26 millimeterblades metallicnumber of blades 1number of positions for cut - height adjustment 2number of levers for cut - height adjustment single levernumber of wheels 4front wheel size 200 millimeterrear wheel size 200 millimeterwheel tyres pneumaticif yes, grass catcher / collector / bag volume 88 liter"engine power rating (watt)" 4000 to 4999engine fuel tank capacity - 1 ltr., lopperanvil tree branch lopper lade material - high carbon steel with hard surface treatment, overall length - not less than 914 mm handle material - similar materil as per requirement, weight - 1.5 kg., cutting dia - not less than 38mm

Corporations And Associations And Others

CTN :43499290

15 Jan, 2026 1.49 Lacs

Delhi - Delhi

Tender For supply of machinery/tools for various parks at pul pehladpur ward no. 179 in central zone - brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hp max output shaft speed at cutting attachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml. weight( dry,without cutting attachment & deflector): should not be more than 7.5 kgclutch: centrifugal type, clutch shoe support base & lining metal only. multi function handle: should have acceleration ,on/off switch at right handle. brushcutter harness: should be double shoulder harness only. anti vibration system: must have 4- point aniti vibration system. vibration level in m/s2 at right handle : should not be more than 2.5 m/s2 sound pressure level db(a): should not be more than 105 db(a) drive shaft design: must have drive shaft ends square design type only. certification : must have valid en certificaton, petrol operated pole prunnerengine : single cylinder, 2 stroke, air cooled onlydisplacement: should be between 25-30 cc power output : should be minimum 1.2 hpweight (dry without cutting attachment & fuel ): should not be more than 7.5 kgfuel tank capacity (ml): should be minimum 400mlchain oil capcity (ml): must have minimum 200 ml.clutch : clutch shoe linining should be metal only.guide bar length : minimum 30cm guide bar and chain : should have same manufacture only .chain type : every drive link need groove & small oil holes for better lubrication. saw chain pitch should be 1/4" or 3/8picco only and drive link thickness must have 1.1 mm or 1,3 mm.max.output shaft speed (rpm): should be minimum 8000 rpm at chain sprocket.equipment total length with guide bar and chain ( cm ) : should be mimimum 220 cm - compressed & total length of equipment - minimum 350 cm - extended. sound pressure level (db/a): should not be more than 95 db(a)vibration measurement m/s2 at control handle - extended poistion : should not be more than 5.5 m/s2certification : must have tuv certification with test standard en iso 11680., hedge trimmerengine: 2- stroke - single cylinder air cooled.engine displacement: should be between 20-25 ccpower output: should be minimunm 1 hpfuel tank capacity: minimum 400 mlweight: should not be more than 6.0 kgclutch: clutch linning should be metal only.handle: must have rotating multi-function handleanti vibration system: must have spring loaded technology for anti vibration system design: should have double sided blade with tooth spacing minimum 35mm bar length: minimum 600 mmblade: should have chrome plated -anti corrsion. stroke rate ( l/min): minimum 3000 vibration level m/s2 at right handle: should not be more than 3.5 m/s2.sound pressure level (db..(a)): should not be more than 95certification: should have tuv with en iso 10517:2009, lopperanvil tree branch lopper lade material - high carbon steel with hard surface treatment, overall length - not less than 914 mm handle material - similar materil as per requirement, weight - 1.5 kg., cutting dia - not less than 38mm

CTN :43421037

16 Jan, 2026 NA

Kamrup - Assam

Tender For corrigendum : supply of mm shaped dorsal distal radius locking plate variable 3 holes in distal horizontal part and 3dash6 holes in longitudinal part with 4 x locking and 1 x cortical mri safe , 2dot4slash2dot7 mm l shaped dorsal distal radius locking plate variable angle with 2 holes in distal horizontal part and 3dash6 holes in longitudinal part with 4 x locking and 1 x cortical mri safe , locking opening wedge tibial osteotomy plate for 7dot5mm to 17dot5mm wedges increments of 2dot5mm with 4 locking cancellousslashcortical screws titanium implants and ce certified , anti rotation proximal femoral nailing system 15consisting of antirotation proximal femoral nail 01 noscoma lag screws 01 nos distal screws 02 nos , knee arthroscopy punch , knee arthroscopy scissor , disposable pulse lavage system dot approvedslashregistered , tubular external fixator for lower limblower limb tibia set 04tubular rod 09 inch long plus universal clamp dash15plus4dot5 mm dia 06 inch long sentze screw 06 rod to rod clamp 06 , arthroscopic pump tubing set with two puncture needles , aggressive cutter shaver blades for arthroscopoic shaver systemdot implants should be dot slash ce european certifiedcoma sterile packed arthrexdotbox of five , interlocking cannulated anatomical femoral nailstrochantric entry5dash 7 degrees proximal offsetright and left with option of gt to lt lockingslash transverse locking with 4x 5slash4dot9 mm , knee scorpion is todash the single portal suture passer with low profile 5 degree up curve and 3dot2mm narrow and 4dot6mm widthcoma it must be a resuable device to be used , wire kirschner 20 cm long x 1mm diacoma 316 lvm stainless steeldot , wire kirschner 20 cm long x 1dot5mm diacoma 316 lvm stainless steeldot , threaded kdashwires stainless steel 2dot0mm diacoma150mm lengthcoma 316 lvm stainless steeldot , ao pattern locking compression plates 6 holes 3dot5mm with 7 x 3dot5mm locking and 2 x 3dot5mm cortical screws dashtitanium complete constructdot , 2dot7slash3dot5 mm locking mid shaftslash distallateral end clavicular locking plate for superior placement right 8 holes with 5 locking and 2 cortical screws c implants mri safe , 3dot5 mm lcp posteriodashlateral distal humerus plate rt lateral extension 6 holes for shaft and 4dash5 holes for articularslashextra articular lateral condylar fragment , 2dot4slash2dot7 mm volar distal radius locking plate with 5 holes in horizontalslashoblique distal part in a single row and 3 holes in longitudinal part of plate with 5 x locking , 2dot4slash2dot7 mm volar distal radius locking plate with 5 holes in horizontalslashoblique distal part in a single row and 5 holes in longitudinal part of plate with 5 x locking , 3dot5mm lcp for proximal lateral tibia minimum 3 rafting screw for subchondral part and 3dash4 screws in metaphyseal region options and 5holes for shaft with 8 x 3dot5mm , 3dot5mm lcp for proximal lateral tibia with minimum 3 rafting screw for subchondral part and 3dash4 screws in metaphyseal region options and 6 holes for shaft with 8 x 3 , predash sterile hydrofiber skin friendly flexible waterproof dressing size 9x15 cm , predash sterile hydrofiber skin friendly flexible waterproof dressing size 9x25cm , predash sterile hydrofiber skin friendly flexible waterproof dressing size 9x30 cm , fiber stitch all inside meniscal repair , ao pattern 4dot0 mm partially threaded cannulated cancellous screws 20 to 80 mm length with washer titaniumcoma should be mri safedot , ao pattern 6dot5mm cannulated cancellous screwcoma fully //bid details2 / 90threadedcoma selfdashtappingcoma length 30mm to 85mm with washer titaniumcoma should be mri safedot , ilizarov fixator frame for deformity correction tibia adult consisting of 8 x 160 mm half ringscoma 2 x 160 mm 5slash8 ringscoma 1 x 160mm foot framecoma 10 x cannulated , disposable screen cover and trolley cover dotslash dot full quality assurance , saw blades 1dot27mm for bpl2 synthes power system smallslashmediumslash broad , vertical

CTN :43549162

22 Jan, 2026 NA

Ganganagar - Rajasthan

Tender For supply of lv7 krz ct 103a 370800001 starter , lv7 krz 257 1104650 fuel cock selector assy , lv7 krz 210 3802040 b1 speedometer flexible shaft , lv7 tata 000 1510 049j ce bearing , lv7 tata 2920 000139 solenoid switch 12 volt , lv7 tmb 2751 1540 3402 bearing bush ce , lv7 tmb 2625 4626 c e bush , lv7 itr beml 5310 006454 nut lock hex lh threads precision steel , lv7 itr beml 2530 001742 rod threaded end lot 1 to 3 , lv7 itr beml 50 66 40 punched washer a-18 lot 1

CTN :42659521

13 Jan, 2026 7.87 Lacs

Ambala - Haryana

Tender For bid to ras supply of bandage plaster of paris 10 cm into 3 metres , bandage plaster of paris 15 cm into 3 metres , post op dressing non woven non adherent with wound pad 5 into 7 , post op dressing non woven non adherent with wound pad 8 into 15 cm , sterile skin marking pencil , disposable screen cover and trolley cover bis , disposable leg o u drape bis us fda eu ce , sterile disposable universal e into tremity drape with conforming circular fenestration tube holders , sterile disposable u drape with tube holders 80 into 124 4 into 44 split compliant , ao pattern lc dcp plate 4 point 5mm broad 8 10 12 14 16 holes , ao pattern reconstruction plates 3 point 5 mm 8 10 12 holes , ss cercalge wire 16 gauge 18 gauge 20 gauge 22 gauge , steinmann pins dia 3 point 5 mm 4 point 0mm 4 point 5mm , steinmann pins dia 5mm 6mm into 175 mm long with trocar tip , schanz screws 2 point 5mm 3 point 5mm self drilling and tapping 100 mm , schanz screws 4 point 5mm self tapping 25 30mm threading 150 175 mm , schanz screws 5 mm 6mm self tapping with 40 50mm threading 200 mm length stainless steel , wire kirschner 20 cm long into 1mm 1 point 5mm 2mm 2 point 5mm 3mm dia 316 lvm stainless steel point , ao pattern cortical screws 3 point 5mm dia self tapping lengths 10 to 60 mm titanium point , ao pattern locking head screws 3 point 5mm dia self tapping lengths , ao pattern lc dcp plate 3 point 5mm 6 7 8 9 10 12 14 hole with 8 self tapping , ao pattern 1 3rd tubular plates 3 point 5mm 6 8 10 holes 316 lvm stainless steel , ao pattern locking compression plates 6 7 8 10 12 14 holes 3 point , ao pattern locking compression plates 6 7 8 10 12 14holes 3 point 5mm , 3 point 5 mm lcp clavicular hook plates for left and right side 12 15 18mm , 3 point 5 mm clavicular shaft anatomical locking plates for superior placement , titanium elastc nails 1 point 5 to 4 point 5mm dia increments of 0 point 5mm , 6 hole 3 point 5 mm titanium dcp plate with 14 mmcortical screw 10 nos , 7 hole 3 point 5 mm titanium dcp plate with 16 mm cortical screw 10 nos , 8 hole 3 point 5 mm titanium dcp plate with 18 mm cortical screw 10 nos , 3 point 5 mm corte into screw length 10 mm to 40mm self tapping titanium , locking head screw dia 3 point 5 mm length 14 mm 30 mm self tapping titanium , fiber tape size 2 white blue working len point 15 sterile , fiber tape size 2 white black working len point 15 sterile , fiber wire with needle white size 2 sterile , fiber wire with needle white blue size 2 sterile , fiber wire with needle white green size 2 sterile , fiber wire with needle multi color size 2 sterile //bid details 2 / 34

Central Government/Public Sector

CTN :42181126

23 Jan, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For corrigendum : procurement of spares for feeder coc gearbox installed at ntpc northkaranpura stpp - comp gear box unit,petl,spl-337 q hw, wheel shaft,steel,petl,spl-337 q hw, worm wheel 60t,ph brnz,petl,spl-337 q hw, worm shaft,steel,petl,spl-337 q hw, pinion 24t,steel,petl,spl-337 q hw, pinion 16t,steel,petl,spl-337 q hw, pinion 16t,steel,petl,spl337 q hw, hub-torque,cstl/en8,petl,spl337 q hw, bush shear pin,steel,petl,spl337 q hw, wheel 54t,steel,petl,spl337 q hw, wheel 49t,steel,petl,spl337 q hw, wheel 41t,steel,petl,spl337 q hw, nilos ring,steel,petl,spl337 q hw, washer set,petl,spl337 q hw, bearing housing,ci,petl,spl337 q hw