Latest laser flash measurement system Tenders | Government laser flash measurement system Tenders

State Government

CTN :45498716

01 Jul, 2026 16.63 Lacs

Delhi - Delhi

Tender For supply of set up to find the coefficient of thermal conductivity of a good conductor (copper) using searl's me , setup to find numerical aperture of an optical fibre , set up to use a prism shaped double refracting crystal to determine the refractive indices of the qu , set up to measure birefringence of mica , set up to determine the cofficient of viscosity using capilary flow method , sextant , set up to measure of planck s constant using black body radiation and photo-detector , set up to find the coefficient of thermal conductivity of copper (cu) by angstrom method , set up to calibrate a thermocouple to measure temperature in a specified range by direct method and/ , set up to study the variation of thermo e. m. f. of thermocouple with difference of temperature of its , setup to determine the temperature coefficient of resistance using platinum resistance thermometer ( , setup to determine the temperature coefficient of resistance by platinum resistance thermometer (prt , set up to determine coefficient of themal conductivity of a bad conductor by lee and charlton's disc , set up to study the pe hysteresis loop of a ferroelectric crystal probes arrangement , set up to measure the dielectric constant of a dielectric materials with frequency , set up for the measurement of field strength b and its variation in a solenoid (determine db/dx) , set up to study magnetic field variation along the axis of a circular coil and in a helmholtz coil

State Government

CTN :45506114

26 Jun, 2026 NA

Kupwara - Jammu And Kashmir

Tender For supply of hall effect measurement system , dielectric constant measurement setup , ferroelectric pe loop tracer , gm counter (integral geiger-muller counting system, microcontroller-based, suitable for beta gamma d

CTN :45498738

25 Jun, 2026 NA

Jaunpur - Uttar Pradesh

Tender For supply of temperature dependent hall measurement setup

CTN :45475065

18 Jun, 2026 NA

Krishnagiri - Tamil Nadu

Tender For procurement and installation of ece lab equipments - procurement and installation of ece lab equipments, single output variable dc rpsu single output regulated power supply- input voltage: 230v/50hzac- output voltage: (0 30v)dc- output current: (0 2a)dc- protection circuit: over voltage and over current protection, short-circuit protection- high efficiency: greater than 85%- low ripple and noise: less than 50 mv, dual output variable dc rpsudual output regulated power supply- input voltage: 230v/50hzac- output voltage: (0 30v)dc- output current: (0 2a)dc- protection circuit: over voltage and over current protection, short-circuit protection- high efficiency: greater than 85%- low ripple and noise: less than 50 mv, function generatorfrequency range: 0.1 hz to 2 mhz.display: 4 to 6 digit led displayoutput waveforms: sine, triangle, square, pulse, ramp.amplitude: 0 20 vp-p.rise time: 100 ns.distortion: 1% (within acceptable range of frequencies).power supply: ac 220 v 10%, 50-60 hzoutput amplifier protection: protected against short circuit and 15v overload, digital storage oscilloscopebandwidth: 50 - 100 mhz.sampling rate: 1gs/s.channels: 2 (minimum)power supply: 100v 240v ac, 50-60 hzautomatic measurement: vpp, vavg,rms, frequency, period, vmax, vmin, rise time, fall time, + width, - width, +duty, - duty etc.,horizontal scale: 5 ns/div 100 ns/div or equivalentvertical resolution: 8 bits (2 channels simultaneously)vertical sensitivity: 1 mv/div 10 v/div (at input)waveform math: +, -, x , , invert, fft etc.,waveform storage: 16 waveforms or equivalentcommunication interface: usb host, usb interface.7-inch color display or equivalentbasic trigger functions, digital vo;tmeterdc voltmeter digital 3 digit display (0-100 v), 0.5 % accuracy (class 0.5 equivalent) (2000), digital ammeterdc ammeter digital 3 digit display (0-2 a), 0.5 % accuracy (class 0.5 equivalent) (1500), eliminator transformer (stepdown)input - 220v - 240v ac, 50 hz, output-2v to 12v dc, 0-2 a ripple: 5mv, embedded lpc 2148 kit cpu - lpc2148, core - 16/32 bit arm7dmi-s speed - max 60 mhz, flash - 512kb, ram (on-chip) - 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converter with 14 analog inputs, one 10bit d/a converter, six pwm &watchdog two uarts (16c550), two i2c (400kb/s), two spi s eight bit digital output, eight bit digital input, 16 x 2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay & buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connectorand usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board example programs in embedded c and assembly with documentation (soft copy) power chord, user manual with cd/dvd, free demonstration after delivery, single phase induction motorsingle phase induction motor, 230v ac, 50hz supply.power rating 1 hp (0.75 kw).speed 1440 rpm.capacitor start/run type suitable for lab useloading setup portable ammeter and digital tactometer contact type, single phase autotransformerinput - single-phase, 230v/240v, 50 hz, 4a, ac output - 0 to 270vac, class "h" or class f insulation., lvdt trainer kitac mains power supply : 230v 10%, 50hzfixed regulated dc power supply : +5v, 12v /500matransducer : lvdtlvdt displacement : 20mm (40mm total)displacement scale : linear 20mmdisplacement display (mm) : red color 3 digit led displayexcitation frequency : 4khzexcitation voltage : ac variable 5v, strain guage trainer kitmetal foil strain gauge mounted on beam/cantileverstrain measurement under applied loadwheatstone bridge arrangementsignal conditioning and amplification circuitinstrumentation amplifiers, 3 digit display of strain / output voltagezero and gain adjustment controlsprovision for applying calibrated loadsregulated power supply, 230 v ac, 50 hztable-top tr

CTN :45416327

16 Jun, 2026 11.00 Lacs

Payyanur - Kerala

Tender For supply of multi process control trainer setup for instrumentation engineering lab under mhrd scheme - purchase of multiprocess control trainer setup for instrumentation engineering lab under mhrd scheme - multiprocess control trainer set up, multiprocess control trainer set up - specifications:- setup must contain flow, pressure, level, temperature loops also derived loops like cascade and feedforward loops. temperature loop must be independent. setups consist of a circulating closed loop water plant or circulating water system including control valve, tanks, independent pumps and necessary valves including bypass valves and rotameters. using this we can be able to do flow control loop with pid,level control loop with pid,and pressure control pid, as independent experiments.the setup must include the following:1.one linear characteristics diaphragm operated control valve with 15mm stroke 1/2-inch size, type: high-capacity globe seat leakage class (as per ansi/fci 70.2).2.measuring tank with volumetric measurement scale and 1000mm level, in of 25 ltr capacity. sump tank min of 40 ltr capacity. all tanks made of ss304, with sight glass, and finished with mat steel finish.3.2 no s smart dp transmitter for flow and level measurement with hart protocol, display and keys integrated for calibration,0-1000mmh2o measurement range,0.01% accuracy, international iso certified ce approved make,24v supply,4-20ma output, loop powered.4,1nos of magnetic flowmeter with display and keys integrated for calibration,0-2000lph measurement range, read out: 0 - 100%, 4-20ma lcd display,0.05% accuracy, international iso certified ce approved make,24v supply,4-20ma output to measure flow as a independent loop.5,. smart pressure transmitter and temperature transmitters with hart protocol, display and keys integrated for calibration, pressure transmitter 0-10bar measurement range, read out: 0 - 100%, 4-20ma lcd display,0.05% accuracy, temperature transmitter 0-250 rtd type international iso certified ce approved make,24v supply,4-20ma output, loop powered.6, pressure tank of 24 liters with necessary valves for pressure loop.7.1nos orifice plate (ss304) and assembly grade with flange 1/2-inch size for flow measurement.8.2 nos pumps 0.5hp, ss centrifugal pump, minimum 1-inch pipeline of ss or high-pressure withstanding plastic with plastic welding.9. rotameters 2nos 1 inch size flow: 200-2000 l/h,ss thread, clear acrylic type.10, plc control station with 4 analogue inputs and one analogue output with necessary digital inputs and outputs to operate all loops directly from panel side.plc must have ethernet connectivity with supported protocols profinet and modbus tcpip.11.required all pneumatic components to full fill the process loops such as fr,needle valves etc.12,i to p converter 4-20ma to 3-15psi with 1/4" process connection with proper copper copper tubing.13, loop including flow pid control, level pid control, pressure pid control, cascade control (level flow), ratio control (flow flow).14.all loops can be operated using a scada system and independent pushbutton control includes trend of all analogue signals and pid tuning. scada direct profinet connectivity to plc and computer with intel i5 processor, 8gb ddr3 ram,1tb sata hdd,licenced windows 11 professional.15, required a standalone software application that must be installed on pc in which it can used to control and monitor all the functions used in scada. the application must contain process parameter trend graph plot for to study about process loops.16.the whole system setup must be in ms powder coated standalone mobile table with lockable castor wheels. all the components used be industrial. copper tubing for air connection, pressure gauges 4inches 3nos, electrical wiring connection to be flexible for to connect field devices. panel with switches, indicator, test points with banana connectors as required, multistrand wire with proper insulated lugs, ferruling & neat wire dressing & clam

CTN :45430786

18 Jun, 2026 NA

Ariyalur - Tamil Nadu

Tender For supply of electronics andcommunication engineering lab materials - electronics and communication engineering lab materials, dso (digital storage oscilloscope)bandwidth: 50 - 100 mhz.sampling rate: 1gs/s.channels: 2 (minimum)power supply: 100v 240v ac, 50-60 hzautomatic measurement: vpp, vavg,rms, frequency, period, vmax, vmin, rise time, fall time, + width, - width, +duty, - duty etc.,horizontal scale: 5 ns/div 100 ns/div or equivalentvertical resolution: 8 bits (2 channels simultaneously)vertical sensitivity: 1 mv/div 10 v/div (at input)waveform math: +, -, x , , invert, fft etc.,waveform storage: 16 waveforms or equivalentcommunication interface: usb host, usb interface.7-inch color display or equivalentbasic trigger functions, digital ic trainer kit with breadboard5v dc, 1a regulated power supply 12v dc / 15v, 200 ma regulated power supplysolderless breadboard to accommodate 8 16-pin icszif (zero insertion force) ic socketssupports ttl and cmos icslogic io leds for output monitoring8 buffered led outputs8 debounced switch inputsttl clock: 1 mhzvariable clock generator: 0.5 hz to 50 hzsingle pulse output: 100 ms (buffered, positive and negative outputs)one seven-segment display with 4 bcd inputsbuilt-in logic probesbuilt-in logic switchesexperiments on basic logic gates, flip-flops, counters, and multiplexers, eliminator transformer (stepdown)input - 220v - 240v ac, 50 hz, output-2v to 12v dc, 0-2 a ripple: 5mv, decade resistance boxrange: 1 to 10 m , steps: 1-10-100-1k-10k, accuracy 1%, suitable for filter and oscillator experiments, decade inductance boxrange: 1 h to 10 h, rotary switch selection, low loss inductors, accuracy 1%, , suitable for filter and oscillator experiments, 8051 micro controller kitoperating voltage: +5v dc4 kb flash (at89c51) / 8 kb flash (at89s52)ram: 128 bytes internal ram16 2 alphanumeric lcdpush buttons / tactile switchesdip switches for digital inputinbuilt adc interface : ldr,potinbuilt dac interfaceinbuilt stepper motor driver with stepper motorinbuilt dc motor driver with dc motor1x4 led array, 1 x4 keypad, 1x relay1x buzzer, 16x2 lcd display, 1x pwm driver1x hardware interrupt key, inbuilt rtcinbuilt eeprom, inbuilt uart module4x7 segment display, both assembly and c language programmable, pc interfaceable., single phase induction motorsingle phase induction motor, 230v ac, 50hz supply.power rating 1 hp (0.75 kw).speed 1440 rpm.capacitor start/run type suitable for lab useloading setup portable ammeter and digital tactometer contact type, auto transformerinput - single-phase, 230v/240v, 50 hz, 4a, ac output - 0 to 270vac, class "h" or class f insulation., temperature measurement kitsensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc).display: 3 digit led/lcd digital display (typically 200mv fsd).temperature source: portable water kettle or heater block.signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation. test points: multiple 2mm/4mm banana sockets for monitoring input/output signals.power supply: 230v ac, 50hz, single-phase.accessories: includes a glass thermometer, ntc thermistor probe 10k, k-type thermocouple probe, patch cords, and instruction manual., ask modulation and demodulation kitmessage signal 1 : 8 bit variable data, amplitude 5vmessage signal 2 : debounce data, amplitude low (0) & high (5v)message signal 3 :fixed data 25k, 12.5k, 6.25k, 3.12k, amplitude 5vcarrier signal : sine wave frequency 200 khz, amplitude 5vmodulator type : switching icdemodulator : envelope detector & lpfcomparator : lm 311 basedsupply voltage (board) : +12v, +5v / dcsupply current : 100 ma (minimum)input voltage : 230 v/ 50 hz acinterface connectors : 2mm banana socket, dth trainer kitpower supply 200v to 240v ac, 50hz,dish antenna 1.5 aluminum steerable, lnb low noise block down converterinput frequency ku band.output frequency 950 to 1450 mhz.conversion gain 65 db.noise temp 35 degree k max.set top box receiver in traine

CTN :45430790

18 Jun, 2026 NA

Ariyalur - Tamil Nadu

Tender For supply of mechanical engineering lab materials - mechanical engineering lab materials, serve motor drive kitinterface l293d motor driver ic with arduino to control direction of rotation of two dc motors), bldc motor kitbldc motor 1 nobldc motor drive -1noinbuilt volt and ammeter and rpm meterinbuilt power supplyinput 230v ac, lvdt trainer kit complete educational trainer for linear variable differential transformer (lvdt) displacement measurement. built-in ac excitation source and signal conditioning circuitry for lvdt operation. micrometer assembly for precise linear movement of the lvdt core. displacement range ~10 mm with clear front-panel adjustments for zero & calibration. digital display (typically 3 -digit) for direct readout of conditioned output/displacement values. test points and banana sockets for signal observation on external instruments. self-contained unit in a durable enclosure with labeled controls and educational layout. includes user manual and patch cords for experiments. operates on 230 v ac, 50 hz mains supply., multi-cylinder petrolphase : single phase load: mechanical load with ropenumber of cylinders : 4displacement : rope brakepower : 65hp,4000 rpm,1396 ccbrand material : mild steelengine type : 4 stroke self startfrequency : 15hzfuel consumption : petrolfuel tank capacity : 5 letermorh s test rig, tail stock assemblyheavy-duty lathe tailstock assembly for training; cast iron body with base, barrel (quill) ~50 75 mm stroke, hand wheel feed, dead centre mt2/mt3, set over screws for taper turning, spindle clamp, complete with all internal parts for dismantling and reassembly; suitable for 300 400 mm centre height training lathe., dc motorvoltage 220-440 v dcpower - 180 w speed - 200 rpm, hydraulic cylinderdouble acting hydraulic cylinder, bore 40 50 mm, stroke 200 300 mm, working pressure up to 100 160 bar, steel tube with honed bore, hard chromed piston rod, front & rear end caps, piston with seals and wear rings. supplied as standalone unit with suitable mounting for dismantling, inspection and reassembly., hydraulic opreated directional control valve (dcv)manually operated 3/2 or 4/2 way spool type hydraulic directional control valve, nominal size ng06 (cetop 3) or equivalent, rated pressure 210 bar, flow 20 40 lpm; valve body with hardened and ground spool, centering springs, ports p a b t clearly marked. supplied on small mounting plate for dismantling, inspection and assembly practice., bearing with shaft assemblyteaching unit with shaft 25 35 mm dia mounted in housing with deep groove ball bearings (6205 / 6206 class) at both ends; includes locking arrangements (circlips, lock nuts, covers). designed for repeated removal, cleaning, lubrication and refitting of bearings, with provision to mount on bench or test rig., coupling unit using driving and driven shaft plumber block bearing unit1. the plummer block housingmaterial: cast iron (grade fg 200 or equivalent). type: sng or snl series (split-type housing).sealing: felt seals or v-ring seals (to demonstrate lubrication retention).lubrication: provided with a grease nipple at the top center for manual lubrication practice.2. the bearingtype: self-aligning ball bearing (1200 series) or spherical roller bearing (22200 series).bore diameter: standard 25mm or 30 mm (ideal for lab scale).mounting: adapter sleeve mounting (h-series) to teach students how to lock a bearing onto a smooth shaft.3. shafting and couplingshaft material: ground carbon steel (en8 or en9) for high surface finish.coupling type: * flexible coupling: to demonstrate the bearings ability to handle slight misalignment.rigid flange coupling: to demonstrate traditional direct connection.driving/driven setup: one shaft connected to a small electric motor (driving) and the other to a brake drum or load (driven)., spring test machine load & displacement sensing load cel * capacity: 0 10 kno accuracy: 1% fs (better if 0.5% fs) displacement sensor * lvdt / digital encodero accur

CTN :45436338

15 Jun, 2026 NA

Hooghly - West Bengal

Tender For supply installation & commissioning of testing setup for measurement of third harmonic resistive leakage current of lightening arrestor as per technical specification attached. [ warranty period:30 months after the date of delivery ] ]

CTN :45404156

16 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For supply of lab equipment for department of instrumentation and control engineering - i/p and p/i converter, pressure measurement using bourdon tube and lvdt setup, level measurement using float and sight glass indicator, temperature transmitter trainer kit, single phase transformer with load, saybolt viscometer, on off control of temperature process, flow measurement using electromagnetic flowmeter

CTN :45365474

12 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For supply of lab equipment for renewable energy sources department - lab equipment, rc phase shift oscillator (item code: o001), strain guage characteristics kit (item code: o002), load cell characteristics kit (item code: o003), measurement of tank level using rotometer (item code: o004), measurement of tank level using displacer type level transmitter (item code: o005), bourdon tube pressure gauge (item code: o007), pressure gauge (item code: o015/ o007), solar water heater performance test setup (item code: o016)

Laser Flash Measurement System Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government