Latest lasers Tenders | Government lasers Tenders

CTN :44969844

02 Jul, 2026 NA

Indore - Madhya Pradesh

Tender For bid to ras bid to ras bid to ras supply of doped fiber for lasers and amplifiers

Central Government/Public Sector

CTN :45737380

15 Jul, 2026 NA

Jaipur - Rajasthan

Tender For supply of broad specification of disposable arthroscopic knee drape is as follows:- 1. non-woven, fluid-resistant fabric, often with a sterile, waterproof design to prevent fluid strike-through. 2. typically includes a 5cm to 8 cm elastic aperture for the knee, a built-in drainage funnel, a large fluid collection pouch, and sometimes integrated leggings. 3. common sizes are around 160x300cm. 4. shouldhave aami level 3 or 4 standards for high fluid resistance and flame resistance for use near surgical lasers. ]

CTN :45696125

13 Jul, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using driving and dr

CTN :45634745

08 Jul, 2026 NA

Multi City - Multi State

Tender For high speed optical lasers

CTN :45601426

20 Jul, 2026 NA

Indore - Madhya Pradesh

Tender For anti reflection coated plano-convex lenses(diameter 25.4mm and 12.7mm) for high power lasers

CTN :45404122

19 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For corrigendum : supply of equipment for mechanical engineering department - supply of equipment for mechanical engineering department, lathe machine :specification :bed: 2v & 2 flat, induction hardened and ground minimum bed length: 1375 mm bed width: 240 mm capacity: height of centre: 165 mm swing over bed: 320 mm swing over gap: 510 mm swing over cross slide: 180 mm distance between centres: 650 mm slides: cross slide travel: 200 mm compound slide travel: 115 mm spindle: spindle bore: 40 mm spindle nose: thread type, 62 mm spindle taper: mt-3 tail stock: quill diameter: 38.1 mm taper: mt-3 travel: 120 mm speed: no. of speeds: minimum 8 range: (40 800 )rpm threading: metric: (1 6 )mm (min 13 steps) english: (2 24 )tpi (min 19 steps) lead screw: (1 4) tpi electrical: motor: 1.5 hp, 230v/415v, 50 hz drive: v-belt structure: bed: close-grained cast iron (fg 260) gears: hardened steel base: rigid cast iron stand , open cup apparatus :specification :standard compliance: astm d92 / is 1448 (part 69) test method: open cup flash and fire point determination test cup: brass, precision machined with heat resistant handle heater: electric heater (1000 w 10% nickel chromium) with variable control heating rate: 5 6 c per minute (as per standard) temperature range: -6 to 400 c thermometer: astm 11c or equivalent flame applicator: gas test flame with fine control valvebody: stainless steel housing display: analog / digital temperature indicator power supply: 230v ac, 50 hz safety: overheat protection heat insulation , closed cup apparatus :specification :standard compliance: astm d93 / is 1448 (part 21) test cup:brass cup diameter: 50.7 50.8 mm capacity: minimum 70 ml stirring system heater: electric heater 650 w 10% heating rate: 1 12 c/min adjustable ignition: pilot flame with automatic shutter mechanism temperature measurement: thermometer or digital sensor(ip-28c or astm) display: digital temperature display power supply: 230v ac, 50 hz safety:over-temperature cut-off flame safety control , tail stock assembly :specification :medium-duty tailstock assembly for dismantling & assembly quill stroke: minimum 75 mm taper: mt-3 (preferred standard) feed: hand wheel operated features: set-over screws for taper turning spindle locking arrangement body: cast iron (fg 260) spindle: hardened steel, slip gauge :specification :set size: m87 (87 pieces) or equivalent range: 1.001 mm to 100 mm step sizes: 0.001 mm 0.005 mm 0.01 mm material: high-grade alloy steel / tungsten carbide (preferred) hardness: hrc 63 65 accuracy: grade: grade 1 or grade 2 flatne flatness / parallelism: 0.5 m stored in protective wooden boxes to prevent wear; calibration grades include charts for exact sizes , dc motor:specification :type: dc shunt motor (dismantling model) power: minimum 0.5 hp voltage: 220 v dc speed: 1500 rpm poles: 4 pole construction: laminated stator salient poles accessible armature features: cut section / open type suitable for dismantling and reassembly, hydraulic cylinder :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steel calibration grades include charts for exact sizes supply: mounted on training base suitable for dismantling and inspection , hydraulic operated directional control valves (dcv):specification :type: manual spool type dc valve configuration: 4/2 way size: ng06 (cetop 3) rated pressure: 210 bar flow capacity: 20 40 lpm body: hardened steel / cast steel spool: ground and hardened ports: clearly marked (p, a, b, t) supply: mounted on training plate suitable for dismantling and study , bearing with shaft assembly :specification :bore diameter: 50 mm stroke length: 250 mm working pressure: 160 bar cylinder tube: honed steel piston rod: hard chrome plated seals: standard industrial seals end caps: steelsupply:mounted on training base suitable for dismantling and inspection , coupling unit using

corporations/Associations/Others

CTN :45138221

08 Jun, 2026 NA

Koderma - Jharkhand

Tender For corrigendum : providing of custom bid for services - calibration of 3 nos instruments (ir thermometer, digital flue gas analyzer & ndct performance measurement system) along with replacement sensors

State Government

CTN :44984352

07 May, 2026 NA

Calicut - Kerala

Tender For purchase of one number xe annual rate contract lamp (300 w) with monochromator and am 1.5 optical components or corresponding lasers to the smart materials lab,

State Government

CTN :44962719

07 May, 2026 NA

Malappuram - Kerala

Tender For purchase of one number xe annual rate contract lamp (300 w) with monochromator and am 1.5 optical components or corresponding lasers to the smart materials lab, department of nanoscience and technology, university of calicut

CTN :44455226

06 Apr, 2026 NA

Thiruvananthapuram - Kerala

Tender For corrigendum : supply of timer , tem controller , oven , decompression tool , gauge , data logger , thermometer , protractor , probe , hot bonder , thermo couple , controller , tds meter , weighing balance , machine , megger , digital force gauge , infrared thermometer , lcr meter , force gauge , lux meter , micrometer , trammel bar , feeler gauge , ground fault tester , inspection machine , residual field indicator , gauss meter , intensity meterdyeglo , uve lux meter , uv light meter , visible light meter , aerocheck , tam panel psm5 , hoffmanntam panel , surface plate cast iron , protractor mount , fuel quantity test adaptor kit , dmc tool kit , elt tester , reflectometer , mx6 hybrid multi gas detector , ulb tester , analyser , tester , lrra tester , altimeter , clampmeter , air data test set , milli ohm meter , calibrator , sound level meter , vacuum gauge , static charge meter , surface resistivity meter , portable eddy current machine , hydraulic tank , gauge assy push pull , exting fire test , dynamometer , fire extinguisher system , ext fire test , calibration standard , reference standard , calibration block , safety lock actuator cargo , device check vapor seal , test set engine bleed , cart pressure , ground test motor , tensio meter , our side micrometer , bevel protector , dynamometer safety , tons gauge , dial depth gauge , dial test indicator , mechanical force gauge , hygrometer

Lasers Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

corporations/Associations/Others

State Government

State Government