Tender For supply, installation and testing of electronic equipments - supply -ece lab equipments, single output regulated dcvariable power supply- input voltage: 230v / 50hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., dual output regulated dc variable power supply- input voltage: 230v/50 hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., function generator - frequency range: 0.1 hz to 5 mhz. display: 4 to 6 digit led display. output waveforms: sine, triangle, square, pulse, ramp. amplitude: 0 20 vpp. rise time: 100 ns. distortion: 1% within specified frequency range. power supply: 230 v ac 10%, 50 60 hz. output amplifier protection: short-circuit and 15 v, digital ic trainer kit with breadboard - +5 v dc, 1 a regulated power supply. 12 v dc / 15 v dc, 200 ma regulated power supply. solderless breadboard with minimum 840 tie- points,power distribution buses. zif (zero insertion force) ic sockets to accommodate 8 or 16 pin ics. logic input and output leds for output monitoring. 16 buffered led outputs. 16 debounced switch inputs. variable clock generator: 0.5 hz to 50 hz. single pulse output: 100 ms (buffered, positive and negative outputs). one seven-segment display with 4 bcd inputs. built-in logic switches. manual clock: debounced push-button (one pulseper press)., dc voltmeter(digital) - dc digital voltmeter - 3 digit led/lcd display, measurement range: 0 20 v dc,accuracy: class 0.5( 0.5 % full-scale), dc ammeter - dc ammeter digital - 3 digit led/lcd display, measurement range: 0 5 a dc,accuracy: class 0.5 ( 0.5 % full-scale), lvdttrainer kit - ac mains power supply: 230 v 10%, 50 hz. fixed regulated dc power supply: +5 v, 12 v / 500 ma. transducer: lvdt. lvdt displacement: 20 mm (40 mm total). displacement scale: linear 20 mm. displacement display: red color 3 digit led display. excitation frequency: 4 khz. excitation voltage: ac variable excitation voltage up to 5 v., strain gauge trainer kit - ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. instrumentation amplifiers with 3 digit display for strain / output voltage. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual., ask modulation and demodulation kit - message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. supply voltage (board): +12 v, +5 v dc. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., fpga trainer kit - must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb- uart bridge, usb cable. user manual., measurement scale: a vertical steel meter scale, usually with (1mm) graduations, for precise deflection measurement., accessories: includes a set of slotted weights (e.g., (6times 50g) or similar sets) for incremental loading.
Tender For multifunction meter, ct/pt site programmable for input voltage measurement 50-550 v ac, l-l , ct 1/5a , aux supply 24 v dc , led/ lcd digital display , 96 sq. mm , class - 1.0 for measuring parameter v, a, f, pf, kw, kva , kvr , kwh , kvah , kva , rh, run hours , on hours , phase angle , interrupts , thd, events(high , low) part no-wl441010oooo of m/s l&t or the part no- m2m of m/s abb, or part no.- metseem6400bng of m/s- schneider make as per rdso specification no :rdso/pe/spec/tl/0195-2019 (rev.-0) or latest suitable for switch board cabinet for hog compliant high capacity lhb power cars, make-l&t, abb, rishabh , yokins , siemens, socomec & schneider only acceptable as per bill of material of rdso spec. [ warranty period: 30 months after the date of delivery ] ]
Tender For multifunction meter with user programmable ct/pt ratio 5a or 1a ct input for lv or hv networks, input voltage 100-600v l-l auxiliary supply 12-60v ac/dc, display high brightness 3 line 4 digits led, size 96x96 mm, flush mount type, accuracy class 1.0 measurement and display parameters vaf, kw, kvar, kva, kwh, kvarh, kvah, pf, pa, mm, nc, thd run hours and on hours suitable for mounting in switch board cabinets of lhb power cars and lslrd coaches, conforming to rdso spec.no. rdso/pe/spec/tl/0195-2019 (rev.0) or latest. accepted make - rishabh/socomec/siemens/ abb/schneider /yokins/l&t only [ warranty period: 30 months after the date of delivery ] ]
Tender For multi function meter, ct/pt site programmable for input voltage measurement 50-550v ac, l-l, ct-1/5a, aux. supply 24 / 110v dc, led / lcd digital display, 96 sq.cm, class 1.0, for measuring parameter v, a, f, pf, kw, kva, kvar, kwh, kvah, kva, rh, run hours on hours, phase angle interrupts thd events ( high, low ) for switch board cabinet for hog compliant lslrd coaches as per rdso spec no. rdso/pe/spec/tl/0195-2019 (rev. 0 ) . make : l&t, ae, socomec, rishabh, siemens, yokins, abb, schneider only. [ warranty period: 30 months after the date of delivery ] ]
Tender For supply of supply of 6 a sp mcb , supply of 10 a sp mcb , supply of 16 a sp mcb , supply of 20 a sp mcb , supply of 25 a sp mcb , supply of 32 a sp mcb , supply of 20 a dp mcb , supply of 20 a tp mcb , supply of 40 a fp mcb , supply of 63 a fp mcb , supply of 125a four pole fp mccb , supply of 200a four-pole fp mccb , supply of 40 a, double pole, rccb , supply of 63 a four pole mccb , supply of four pole, ac1 rating 40a , contactor , supply of three pole ac3, 32a rating contactor , supply of under current monitoring relay , supply of 3-pole power contactor with add on block , supply of thermal overload relay , supply of rotary operating direct handle for mccb , supply of rotary operating extended handle for mccb , supply of 06 way double door db , supply of weather proof frp junction box , supply of copper flexible cable 2c x 1.5 sq.mm , supply of copper flexible cable 3c x 1.5 sq.mm , supply of copper flexible cable 3c x 2.5 sq.mm , supply of 4 c x 10 sq.mm xlpe armoured aluminium cable , supply of frlsh single core copper conductor 1.5 sqmm , supply of frlsh single core copper conductor 2.5 sqmm , supply of frlsh single core copper conductor 4 sqmm , supply of frlsh single core copper conductor 6 sqmm , supply of heat shrink straight through joint kit for 3.5 core 95 sqmm , supply of 4 feet, 20w energy efficient led batten light fitting , supply of 9w led bulb with b22 base , supply of 20w led bulb with b22 base , supply of square type 36 w led down light , supply of 50 w led fllod light , supply of 70 w led street light , supply of 1200 mm sweep five star rated bldc fan , supply of 150 mm sweep exhaust fan , supply of 400mm sweep pedestal fan , supply of 300mm sweep wall fan , supply of 300 mm sweep table top type rechargeable fan , supply of 5 or 6 amp, 3 pin plug top , supply of 15 or 16 amp, 3 pin plug top , supply of automatic programmable analog time switch , supply of 3 phase digital multifunction meter , supply of flush-mounted analog panel type ammeter , supply of flush-mounted analog panel type voltmeter , supply of panel mounting red pilot light , supply of panel mounting green pilot light , supply of panel mounting yellow pilot light , supply of panel mountingf blue pilot light , supply of panel mounting amber pilot light , supply of connector din rail mounted for 2.5 sq. mm conductors , supply of connector din rail mounted for 25 sq. mm conductors , supply of mild steel din rail 1 mtr length , supply of 20w, 4 feet led tube light , supply of surface mountable, 15w led emergency lamp , supply of 1hp centrifugal pump single phase , supply of digital vernier caliper , supply of addressable photoelectric smoke detector for fire alarm system , supply of addressable zone interface module , supply of audio visual alarm device for addressable fire alarm system , supply of manual call point mcp for addressable fire alarm system , supply of 2 core 1.5 sqmm red fire alarm cable //bid details 2 / 53
Tender For multifunction meter, ct/pt site programmable for input voltage measurement 50-500v ac, l-l, ct 1/5aaux supply 24/110v dc, led/ lcd digital display, 96 sq. cm, class 1.0, for measuring parameter v, a, f, pf, kw,kva, kvr, kwh, kvah, kva, rh, run hours, on hours, phase angle, interrupts, thd, events (high low).material shall conforming rdso specification no. rdso/ pe/ spec/ tl/0195-2019 (rev-0). material approved make l&t part no.wl441010oooo or abb part no. m2m or schnieder part no. metseem6400ngpocl1 /socomec /rishabh /siemens /yokins only [ warranty period: 30 months after the date of delivery ] ]
Tender For supply, installation, testing and commissioning of clamp-on type ultrasonic flowmeter, online continuous effluent monitoring monitoring system, programmable iot panel gsm/gprs, electromagnetic flow meter, open channel ultrasonic flowmeter and all accessories co
Tender For multifunction meter with user programmable ct/pt ratio 5a or 1a ct input for lv or hv networks, input voltage 100-600v l-l auxiliary supply 12-60v ac/dc, display high brightness 3 line 4 digits led, size 96x96 mm, flush mount type, accuracy class 1.0 measurement and display parameters vaf, kw, kvar, kva, kwh, kvarh, kvah, pf, pa, mm, nc, thd run hours and on hours suitable for mounting in switch board cabinets of lhb power cars and lslrd coaches, conforming to rdso spec.no. rdso/pe/spec/tl/0195-2019 (rev.0) or latest. accepted make - socomec/siemens/ abb/schneider /yokins/l&t only [ warranty period: 30 months after the date of delivery ] ]
Tender For supply of various items of lab equipments for govt. p g college guna district guna (m.p.) under p m usha pariyojna 4th call - supply of various lab equipments items for govt. p g college guna district guna (m.p.) 4th call, waterand soil testing analysis kit (digital) : range ph 0 to 14.00 resolution ph 0.01 accuracy ph 0.01 1 digit temp. comp. 0 to 100 deg. c., water bath (06holes) : 6 hole8 ltrs., waterbath(12holes) :12 hole 20 ltrs., water distillation apparatus(single distillation unit 2 litre/hour) : single distillation 5 litres, analytical balance : least cosunt 0.0002g, analytical weight box : 1-100g, fractional weight box : 1-500mg, physical balance : 250gm accuracy 0.1g, digital balance : least count 1mg, single pandigital balance : 0.1mg 200g, digital photoelectric colorimeter : 8 filter,1 ml, digital potentiometer : with hot plate and electrodes, digital conductometer : with cell 1cc and 0.1cc, d.o. meter : polarographic do range: typically 0 to 90 mg/l (milligrams per liter) or 0 to 600% saturation.rdo (optical) do range: usually 0 to 50 mg/l or 0 to 500% saturation., digital naphelo/turbidity meter : digital turbidity cum nephelometer range:-, 200,1000 ntu/jtu resolution:- 0.01 ntu/jtu accuracy:- 3% fs, 1digit display:- 3 digit 7-segment led light source:- ir led detector:- photodiode sample system:- 60 x 25mm clear glass test tubes power:- 230 v 10% ac, 50 hz accessories:- test tube set of 2, operation manual, dust cover, polarimeter half shade : the specific rotation ( ) is a physical property defined as the optical rotation at a path length of 1 dm, a concentration of 10 g/l, a temperature (usually 20 c), and a light wavelength (usually sodium d line at 589.3 nm), melting point apparatus :melting-point measurement range: room temperature - 400 c setting rate of the starting temp. : 50 c~400 c 5 min; 400 c~50 c 7 min minimum digital display: 0.1 c size of the capillary: 1.4mm (outside diameter) 1.0mm (inside diameter), 90mm equipped with color camera and color monitor to observe melting point with ease validation program for standard samples 8 operator names can be storedgraphic lcd display to display all test parameters & test instructions, digital melting point apparatus :melting point measurement range : ambient to 300 deg c starting melting point temperature : settable from 50 to 300 deg c heating time : 3 minutes (up to 300deg c) cooling time : 5 minutes (from 300 deg c) accuracy : +/ 0.5 deg up to 200 +/ 0.8 deg from 200 to 300 temperature display resolution : 0.1 deg c rate of heating (deg c per minute), abbe refractometer : safety bs en 60950-1:11/2006 emc en 55024 : 10/2003 en 55020 : 11/2005, tlc kit : outstanding standardization and quality control exceptional adherence, hardness and surface homogeneity. analyzing samples with high matrix- load without sample preparation. multiple samples analyzed in parallel.highly cost-efficient, fast and economical, centrifuge : 6000rpm, corkboring machine :adjustable guide that permits holes to be bored in any part of a stopper, the knurled chuck - 9/16" (14mm) shank of the eight, plated-steel borers included with the unit. the steel borers range from 3/16" to 5/8" (4.8mm to 15.9mm) in 1/16" (1.6mm) increments,, distillation apparatus : single distillation 5 litres, oven hot air : 14" 14" 14 , voltage stabilizer : 2kv, vertex shaker : 6 tube capacity, mixer small : moter capacity 900 watt, water bath(cu) : 4 , heating mantle with energy regulator : 500 w,2litre, single crucible heater : helical wire coil moldatherm insulation platinel ii thermocouple with 10tm compensated lead wire and polarized plug ceramic fiber hearthplate programmable heat-up to setpoint temperature indicates setpoint and process temperatures temperature: 1200 c (2192 f) maximum crucible sizes: 5 (top vestibule id) x 8 (heated depth), water bath rectangularsingle walled : 6 hole 8 ltrs., water bath rectangular :2 hole, kjeldahl distillation unit : unit of 3 tests, microwave oven : 30 ltr co