Latest lead rail Tenders | Government lead rail Tenders

CTN :42771762

08 Dec, 2025 NA

Darjeeling - West Bengal

Tender For corrigendum : supply of supply of plant spares--bucket teeth , teeth locking pin , locking pin washer , bucket side cutter rh , bucket side cutter lh , bucket pin shim 1 point 2 th , rock breaker chessel , rock breaker hose , hyd filter , side mirror , hyd filter in line , pilot filter , bucket ram seal kit , roller carrier assy , master pin , master pin bush , master pin seal dust , bolt track , nut track , air element inner , air element outer , kit gasket top overhal , kit gasket bottom , thermostat , fuel baby filter , belt v ribbed , radiator cap , radiator hose top , radiator hose bottom , bucket side cutter lh , bucket side cutter rh , tooth bucket , tooth bolt , tooth nut , windscreen front , silicon sealant , mirror rear view , loader bush arm , loader bush , bucket pin , exterior mirror , battery 12v 130ah , head lamp 12v , tail lamp lh , tail lamp rh , arm wiper blade assy , knob gear lever , throttle hand knob , parking breake assy , gear box solenoid assy , hyd jack piston seal kit , boom jack piston seal kit , front tyre tube , front tyre , rear tyre tube , rear adaptor air filling , txn filter , torque conv drive plate , breake master cyl , front belt fan belt , exhaust spring extention , air element inner , fuel line tank to water seprator , fuel filter assy , fuel filter element , eng oil filter , tie rod , alternator , turbo charger , self starter , water seprator , fuel filter , filter , air element set , fuel water serator , teeth bucket , bucket cyl seal kit , fan belt , carring roller upper , oil filter , swing mounting bolt , lower roller assy , black light assy , wiper blade , wiper motor , accelerator cable , g box main shaft brg gb 40 , fuel flexible pipe 19 oblique 19mm , fuel flexible pipe 17 oblique 19mm , oil filter , fuel filter primary , fuel filter secondary , water separator , hub seal front , hub seal rear , hub brg rear inner oblique outer , air filter , 4 x 4 cable , non skid chain front wheel single chain 10 point 00 point 20 16 ply , non skid chain rear wheel double chain 10 point 00 point 20 16 ply , pressure plate with clutch plate , propeller shaft nut bolt with lock patti , rear view mirror both side , clutch cylinder assy , fog light assy , steering oil filter , paint og , fog light bulb , brake shoe for both tyres , battery charger 72v 10 amp , grease gun 5 kg

CTN :42991152

09 Dec, 2025 NA

Jammu - Jammu And Kashmir

Tender For supply of engr spares--locking ring , spider bearing , banjo bolt , kit seal , stabilizer seal kit , boom cyl seal kit , dipper cyl seal kit

Central Government/Public Sector

CTN :42960171

15 Jan, 2026 NA

Multi City - Multi State

Tender For designing, manufacturing, supplying, installation and field trial of 1 in 12 canted turnout with thick-web switch, lead rails & weldable cms crossing, psc sleepers & all fastenings along with back-driving assembly compatible with indian railway standards (irs) type of point machine on ir, including all fittings, fastenings, fixtures, stretcher bars etc. as required with complete arrangement, excluding point machines, rodding's & clamp locks, meeting the laid down technical requirements i.e. generic specifications requirements issued by rdso and for undertaking the field trial as applicable for three variants of canted turnouts. total quantity- 50 sets.

Central Government/Public Sector

CTN :42960417

19 Dec, 2025 NA

Multi City - Multi State

Tender For improvement of road surface, provision of sliding boom with locking arrangement at lcs etc in ara-ssm section.

Central Government / Public Sector

CTN :42796260

12 Dec, 2025 NA

Vijayawada - Andhra Pradesh

Tender For sw-i: (i)vijayawada division: gdr-bza & bza-vskp section: ctr(p) 60 kg. r260 rails on wider sleepers of 1660 density for a total track length of 1.548 tkm.(ii) bza- vskp section: trr(p) of exg. 60kg/90uts rails on psc6 sleepers of 1540/1660 density with new 60kg-r260 grade rails (lwr) for a total length of 1.937 tkm (iii) ki-bza section: tsr(p) with wider psc sleepers of 1660 density for a total track length of 26.600 tkm. sw-ii vijayawada division: (i)gdv-bvrm & gdv-mtm sections tfr: through renewal of fittings(cgrsp only) on psc sleeper track for a total length of 61.89 km.(ii) vijayawada division: bza-bvrm-ndd & gdv-mtm sections through turnout renewal of exg.52/60 kg switches, lead rails and crossings on fan shaped layout(fsl) with new thick web switches, lead rails & weldable cms crossing for a total of 168 sets (fs+tws+wcmsc- 18 sets, tws+wcmsc -150 sets)

CTN :42745489

15 Dec, 2025 NA

Gonda - Uttar Pradesh

Tender For designing, manufacture , supplying installation and field trial of 1 in 12 canted turnout with thick web switch, weldable cms xing, psc sleeper & all fastening along with lead rail, back driving assembly compatible with ir standards (irs) type of point machine on indian railway for 60 kg track, including all fitting, fastening, fixtures, stretcher bar etc. as required with complete arrangement excluding point machine, rodding and clamp locks, meeting the laid down requirements i.e. functional requirement and specification issued by rdso and under taking the field trial as applicable for:- canted turnout fit for speed potential of 45 kmph on diverging line ( it is mandatory that there should be no change in the yard layout for laying such canted turnout i.e. the canted turnouts should be compatible for the existing yards. in case of crossover, the centre to centre distance shall be 5.3 m.).

CTN :42254361

15 Dec, 2025 NA

Gonda - Uttar Pradesh

Tender For corrigendum : designing, manufacture , supplying installation and field trial of 1 in 12 canted turnout with thick web switch, weldable cms xing, psc sleeper & all fastening along with lead rail, back driving assembly compatible with ir standards (irs) type of point machine on indian railway for 60 kg track, including all fitting, fastening, fixtures, stretcher bar etc. as required with complete arrangement excluding point machine, rodding and clamp locks, meeting the laid down requirements i.e. functional requirement and specification issued by rdso and under taking the field trial as applicable for:- canted turnout fit for speed potential of 45 kmph on diverging line ( it is mandatory that there should be no change in the yard layout for laying such canted turnout i.e. the canted turnouts should be compatible for the existing yards. in case of crossover, the centre to centre distance shall be 5.3 m.).

Lead Rail Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

Central Government / Public Sector