Latest lifter fuel pump Tenders | Government lifter fuel pump Tenders

State Government

CTN :45510061

16 Jun, 2026 NA

Parli - Maharashtra

Tender For supply of spares for m/s jyoti make vm pumps of khadka & naikota pump house at tm-ii 250mw tps, parli-v. - pmp wtr jyoti800vm basket strainer, bfv assy with actuator, pmp jyoti 800vm line shaft bearing, pmp jyoti 800vm coupling pupm half, coupling bolt set (1 set=12 nos), pmp jyoti 800vm coumn pipe inter l2000mm, allen bolt flat hd m-16 x 40

CTN :45496120

18 Jun, 2026 22.28 Lacs

Kota - Rajasthan

Tender For tn11194supply of spares of ash slurry pump model d-135 and clinker grinder of ash handling plant pump house stage-i at kstps kota under proprietary category - u seal 916-321(for ash slury pump) pt. no. 916-321, suction sleeve 916-012, shaft 916-305, stuffing box 916-016, shaft sleeve 916-022, impeller part no. 916-029, bell suction side part no.916-010, bell liner suction side 916-011, bell engine side part no. 916-014, liner engine side 916-016, discharge adopter, reducer 12 x 10", bearing retainer ring 916-314, oil level indicator, "compression spring 916-320(1 set of 8 nos.)", oil gauge, 40 nb bsp p. no. 1 1/2" ispt, adopter sleeve 916-312, flinger p. no. 916-026, thrust coller, gland half, spares for clinker grinder assembly for ahp stage-i, "8""x8"" tangential inlet hydro ejector assembly part no. a-218-r/l"

CTN :45474143

18 Jun, 2026 22.28 Lacs

Kota - Rajasthan

Tender For supply of spares of ash slurry pump model d-135 and clinker grinder of ash handling plant pump house stage-i at kstps kota under proprietary category- u seal 916-321(for ash slury pump) pt. no. 916-321 , suction sleeve 916-012 , shaft 916-305 , stuffing box 916-016 , shaft sleeve 916-022 , impeller part no. 916-029 , bell suction side part no.916-010 , bell liner suction side 916-011 , bell engine side part no. 916-014 , liner engine side 916-016 , discharge adopter , reducer 12 x 10" , bearing retainer ring 916-314 , oil level indicator , compression spring , oil gauge, 40 nb bsp p. no. 1 1/2" ispt , adopter sleeve 916-312 , flinger p. no. 916-026 , thrust coller , gland half , spares for clinker grinder assembly for ahp stage-l , 8"x8" tangential inlet , hydro ejector , assembly

State Government

CTN :45442802

18 Jun, 2026 4.93 Lacs

Umaria - Madhya Pradesh

Tender For procurement of “spares for dewatering pumps (make-kirloskar pumps type kpds-40/13)” installed at fuel oil pump house at, sgtps, mppgcl, birsinghpur - std column pipe, impeller enclosed, intermediae shaft, head shaft, impeller shaft, casing ring, impeller ring, bearing spacer, split lantern ring, split gland, st box housing, bearing spider, thrust brg carrier, bearing cover, cover plate-casing cover, cover plate-brg spider, eye bolt-m16x28l, shaft sleeve d.s., shaft sleeve-ps, impeller nut with helicoil insert, bearing nut, bearing nut, round pipe nut, shaft nut-, inter brg bush-, bearing bush-, coupling gaurd, screwed coupling, gland packing, gasket set, o ring set, key set, .

State Government

CTN :45398558

09 Jun, 2026 NA

Parli - Maharashtra

Tender For supply of spares for m/s jyoti make vm pumps of khadka & naikota pump house at tm-ii 250mw tps, parli-v. -pmp wtr jyoti800vm basket strainer, bfv assy with actuator, pmp jyoti 800vm line shaft bearing, pmp jyoti 800vm coupling pupm half, coupling bolt set (1 set=12 nos), pmp jyoti 800vm coumn pipe inter l2000mm, allen bolt flat hd m-16 x 40

CTN :45327550

11 Jun, 2026 NA

Jummu - Jammu And Kashmir

Tender For providing of consumable material/spares for routine maintenance/ operation of 1000hp/750kw ht slip ring induction motors at tawi pump house, jammu. - providing of carbon brush holder assembly as per sample (an assembly comprises of 6 no. brush holders and 12 nos. carbon brushes of size 32x38x55mm) with tension springs and pin holding slots for different adjustment, having current carrying capacity of 650 amp, fabricated out of gun metal material for fitment to jyoti/ bhel make 1000hp /750kw slip ring induction motor installed at tawi pump house, jammu., providing of spare sets of copper carbon brushes of size 32x38x55mm for 750kw/1000hp, 6.6kv slip ring induction motor (1 set comprises of 12 nos. carbon brushes), providing of rubber bearings for 900 vm-2, 60 cusecs vt pumps as per sample casted out of superior quality rubber finished to the required size having size height 230mm, inner dia. 95 mm and outer dia. 125 mm with proper facing on both ends for proper fitment., ravi canal :- d-18 h/r, dol vijaypur. complete job.

CTN :45305461

15 Jun, 2026 7.41 Lacs

Nellore - Andhra Pradesh

Tender For break down & repair works, which include complete dismantling, overhauling and reassembling of vt pumps after replacement of worn-out spares. the scope also covers patch welding works at sea water intake pump house as and when required during the year 2026-27 at ahp-ii&swph/sdstps/stg-ii

State Government

CTN :45304203

08 Jun, 2026 8.33 Lacs

Umaria - Madhya Pradesh

Tender For procurement of spares for dewatering pumps make-maxflow pumps type 50-smp1 installed at fuel oil unloading pump house at unit no. 1 and 2 sgtps mppgcl, birsinghpur - as per schedule, strainer, suction cover, pressure body, impeller (semi - open), impeller nut, impeller key, pump shaft, block, seal plate, oil seal, block bush, top spider, line spider, top spider bush, line spider bush, line shaft, top shaft, pump shaft coupling, bearing sleeve, ratchet plate, grease nipple, pump coupling, ratchet pin, top adjusting nut, coupling rubber, motor coupling, line shaft coupling, gasket, suspension pipe, delivery pipe, .

Central Government/Public Sector

CTN :45034292

01 Jun, 2026 NA

Koradi - Maharashtra

Tender For corrigendum : supply of single girder eot hot misc crane - 8t - compressor house - indoor- non hazardous area , single girder eot hot misc crane - 8t - dg room -indoor - non hazardous area , single girder eot hot misc crane - 5t - acw pump house - indoor - non hazardous area , single girder eot hot misc crane - 5t - outside cw pump house - screens and gates handling -outdoor - non hazardous area , single girder eot hot misc cranes - 2t - fuel oil pump house - indoor - hazardous area , maintenance tools and tackles , supervision of e and c - prices for visits , supervision of e and c - number of days , mandatory spares

State Government

CTN :45275642

02 Jun, 2026 3.07 Lacs

Serampore - West Bengal

Tender For repairing and overhauling of one no twin lobe air blower assembly and renovation of 2 nos outgoing motor (blower ) feeder of lt pdb with supply, fitting and fixing spares at sludge pump house under swtp, kmda. - supply,installation,testing and commisioning of following items for hoisting system/ blower and gear box as mentioned below as per direction including cost of materials, machinaries , manpower, cutting,machining,aligning,anchoring,welding,finishing,consumables, carriage and all overheads with all leads and lifts complete as per specification (without painting), i) base frame (ms), ii) shaft/pin with key ways made of ss-304, iii) gear& pinion (forged steel), supply and fixing the 3way c.i v grooved pulley with complete mechanism key way suitable to en-24, 60 mm dia/ as per sample of shaft end., a) motor driving, b) blower driving, supply of gear oil as per direction of engineer in charge., supply of grease, supply and delivery of the following bearing (make: skf):, i) 22312e/c3/ as per sample. (for blower), supply and fixing of tough v belts (make: fenner/power boom / v guard/benq/ecodrive) of the following size c 98/ as per sample., supply fitting fixing of ss (aisi304) bolts,nut & washer i) dia 10 mm to 20 mm a) length upto 75 mm, refixing of impeller of blower after dynamic balancing in workshop as per is rule after dismantling the same., dismantling the 25/30 h.p (18.5 kw)//30 h.p squirrel cage motor from its foundation by opening mounting bolts and disconnection of cables from terminal box and open the v belts for repairing purpose (in condition), preliminary checking of the whole motor (lt sq. cage im) and testing of i.r. value, load currents, leakage factor of stator & rotor, terminal lead joints of stator connection ends, insulation of glass fibre terminal bar, double cage rotor end rings and all of motor bars and bar joints, housing of d.e. & nde shield bearing housing etc. before work to detect fault., complete servicing and heat varnishing of 415volt, 3 phase l.t. sq. cage induction motor after cleaning the stator and heating it up periodically and varnishing by dr. beck s graded insulating varnish to obtain stable ir value, cleaning up the rotor, including heating for demoisturisation, lacker coating on the surface of rotor stampings, cleaning and ro priming on the end shield covers, bearing housing and complete the necessary repairing works as per direction of e.i.c.upto 75kw lt sq. cage im ], re fixing the 25/30h.p star/delta squirrel cage motor over its foundation by mean of mounting bolts & nuts, washer complete connection of existing led of cable at the terminal box and wear the v belts with proper alignment in respect to i.d. fan (12000 cu m/hr capacity)/ blower by adjusting the side rail for smooth running., finishing the end of terminal leads by s & f dowells copper sockets properly supplying tapes, petrollium jelly etc. 6 nos.upto 75kw lt sq. cage im., cost of mechanical work viz. shaft truness, checking key way looping of holes grinding and polishing etc. upto 75kw lt sq. cage im., inspection checking/testing and servicing of the existing starter panel, all terminal connection, contactors, relays etc as per desired technical specification including man and minor materials for proper functioning as per direction of eic., supply and fixing of 240/230 volt, 50 hz, t.p., power contactor (make: l & /abb/schneider/ simence/ ge) having contact block of the following range.32-55amp, supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) blue/ white color., supply & fixing of 230/240v, led indicating lamp make :ae/kappa/imp) other than blue/ white color., supply and delivery of thermal overload relays (make: l & t/abb/schneider/simence/ ge/minilec) of the following range:a) 0.2-0.33/ 0.3-0,5/ 0.45-0.75, mn2, supply of ammeter selector switch current in each phase with off, 4 pos. 90 angle ofthrow (off-r-y-b) , supply and fixing of analog ammeter ranging

Lifter Fuel Pump Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

State Government

State Government

State Government

State Government

Central Government/Public Sector

State Government