Tender For corrigendum : supply installation testing and commissioning of pump unit and other electro-mechanical equipments at laripora pahalgam - supply, installation, testing and commissioning of submersible type pump sets with motors and allied mechanical and electrical components/ items as per manufacturer s recommendations and guide lines, and as per the scope of the work at site. the equipment supplied conform to latest is- standards and codes with fail safe circuits/ devices for(i) over loading (ii) under loading (iii) clogging (iv) shut off (v) low liquid level (vi) single phase prevention devices (vii) over heating etc. the pumping units shall have following technical specifications: pumps:type of pump :non clog centrifugal volute type sewage submersiblepumpscapacity= 28.4lpshead = 17.5 metres or abovesolid handling capacity: 20mm (minimum) quality of water: sewage water to be handled meterial of construction:pump casing : cast ironimpeller : stainless steelpump shaft : stainless steelmotor body : cast ironsealing : dual mech. seal...contd.. as per annexure-a, providing/supplying and fitting of 100 mm m.s flanged delivery main to be connected with existing rising main at site. the job includes providing and welding of m.s flanges 12 mm thickness. the flanges shall be double welded both from inside and outside of the pipe using standard electrode of reputed make. the cost on account of supply/ fabrication of bends and providing/ fitting of flanges is included in the job. (complete job)., providing and fitting of 100 mm dia ductile iron double flanged, non-rising spindle soft seated glandless gate/ sluice valves as per is14846 for regulating the water supply outside the pumping units p.n rating 1.0.the job includes providing and fitting of 02 nos. m.s flanges perfectly adaptable to the inbuilt flanges of the valve which shall be fitted with rising main of the pumping unit at appropriate spots as per site requirement (complete job)., providing and fitting of 100 mm dia ductile iron double flanged, slanted seat swing check valve( nrv) as per is 5312 p.n rating 1.0.the job includes providing and fitting of 02 nos. m.s flanges perfectly adaptable to the inbuilt flanges of the valve which shall be fitted with rising main of the pumping unit at appropriate spots as per site requirement (complete job)., gantry over sump :- fabrication, providing, fitting of ms gantry over sump with 02 nos. vertical columns. the gantry fabricated out of ismb-100, 3.25 mts long placed face to face. 300x300mm ms plates 12mm thick fitted on top and bottom side of column .bottom plate welded to the reinforcement of the sump and grouted in 1mx1mx1m pcc 1:1.5:3 mix. ismb-100,3mts long is to be placed and welded to the top plate of the columns .the job also includes providing and fitting of 2-tonne capacity chain pulley block with monorail along with hoisting chain (complete job)., providing and fitting of 50 mm23.5 core ,al pvc insulated cable, armouredfor internal connectionscrimping, taping etc. note:- the cable terminal ends for connection to switchgear at various requisite points shall be al. thimbles and of appropriate size and connected by hydraulic crimp tool only (complete job)., providing and fitting of 4-core 16 mm2 flat /circular submersible copper cable conforming to is: 694 (part 1st) 1964 & is: 694 (part 2nd) - 1964 for submersible pumping unit and other electrical equipment s. the cable connections terminal shall be fitted with copper thimbles of required size (complete job)., fabrication, providing and fitting of main electric control panel of appropriate size fabricated out of 14 swg sheet having required openings/vents and protection class : ip-55 & fitted with accessories as under: a) bus bar chamber: 160 amperes(tpn) b) main circuit breaker (incomer mccb) qty:- = 01 nocurrent rating = 160 amp. c) change over switch:qty. = 01 no.rating = 160 ampere....contd... as per annexure-a., electrification. providing/fitting of lighting and fan
Tender For supply of electrical work - miniature circuit breaker make: havels/siemens/l&t/bch/schneider, 32 amps, 2 pole mcb without metal enclosure, for lighting circuits, 230v ac, type b or c tripping, is/iec 60898 standard, overload and short circuit protection., 32 amps, 3 pole mcb without metal enclosure, for lighting circuits, 230v ac, type b or c tripping, is/iec 60898 standard, overload and short circuit protection., 63 amps, 3 pole mcb with metal enclosure, for power load circuits, 415v ac, type c or d tripping, is/iec 60898 standard, overload and short circuit protection., 16 amps, 1 pole mcb without metal enclosure, for lighting circuits, 230v ac, type b or c tripping, is/iec 60898 standard, overload and short circuit protection., 20 amps, 1 pole mcb without metal enclosure, for lighting circuits, 230v ac, type b or c tripping, is/iec 60898 standard, overload and short circuit protection., mcb rail 1 meter long., l&t make thermal overload relays (olr), l&t make, thermal overload relay olr: model- mn-5, adjustable 30-50 amps, direct mount, 1no+1nc, ambient compensation, manual/auto reset, iec 60947-4-1., l&t make, thermal overload relay olr: model- mn-5, adjustable 45-75 amps, direct mount, 1no+1nc, ambient compensation, manual/auto reset, iec 60947-4-1., l&t make, thermal overload relay olr: model- mn-5, adjustable 20-33 amps, direct mount, 1no+1nc, ambient compensation, manual/auto reset, iec 60947-4-1., l&t make, thermal overload relay olr: model- mn-5, adjustable 14-23 amps, direct mount, 1no+1nc, ambient compensation, manual/auto reset, iec 60947-4-1, star delta electronic timer, make : gic or l&t or selec, adjustable time range 0.1-60 sec, multifunction, din-rail mount, 2 no+2 nc, led status indication, wide voltage range 230/420 v ac, 50 hz, iec 60947-5-1 compliant., 2 a. hbc fuse - 415 v. a.c., model: ns2, 32 a. hf fuse - 415 v.a.c., model: hf14x51 sf-90159., 63 a. hf fuse - 415 v.a.c., model: hf14x51 sf-90159., fuse wire 16 a. 100 grams pack, fuse wire 32 a. 100 grams pack, fuse wire 63 a. 100 grams pack, dowel make aluminium lugs: (ring type), 35 sq.mm, 70 sq.mm., 95 sq.mm., 120 sq.mm., 150 sq.mm, dowels make copper lugs: (ring type), 4 sq.mm. - hole dia 5mm, 6 sq.mm. - hole dia 8mm, 10 sq.mm. - hole dia 8mm, 25 sq.mm. - hole dia 10mm, 1.5 sq.mm. u-lug (kompress fork type), high-grade porcelain/ceramic heavy-duty industrial pendant holder suitable for a type of bc (bayonet cap) with pin-type contacts, make: crompton/philips/havells/bajaj, 230v, 100w bc (bayonet cap) pin-type incandescent bulb, clear glass, high illumination, and long-lasting performance., 230v, 60w bc (bayonet cap) pin-type incandescent bulb, clear glass, efficient lighting, and extended service life., 24v, 60w bc (bayonet cap) pin-type incandescent bulb, clear glass, high illumination, and durable performance, 22 watts, batten type, 4 feet led tube light - make: isi standard, 230 v. ac 50 watts led flood fitting., 230 v. ac 100 watts led flood fitting., 230 v. ac 150 watts led flood fitting., 3/4 inch wide pvc insulation tape, flame-retardant, moisture-resistant, and suitable for electrical insulation-10 mtrs roll, 1-inch wide fiber glass tape, high-temperature resistant, non-conductive & suitable for electrical insulation and cable wrapping- 50 mtrs roll, 250 w, mercury vapour lamp, screw type, clear/coated, 230 v ac, 50 hz, standard base (e27/e40), suitable for outdoor/indoor lighting applications.
Tender For corrigendum : repair/maint/impv of building service connections, internal lighting system, led lighting and lightningprotection system in various accn at jalapahar under age i darjeeling
Tender For supply of electrical goods in the year 2026-27 in sawyerpuram town panchayat - insluation gum tape roll - isi , 1/18 vir copper wire [1/44] [90mtr], 3/20 cts copper wire [3/36] [90mtr] , 7/20 cts copper wire [7/34] [90mtr] , 1.5 sq.mm 3 core copper cable , 2.5 sq.mm 3 core copper cable , 36w 4pin lamp holder, 36w lamp clip, led fitting top protection glass - street light, led fitting top protection glass - flood light, 20 / 25 mm 1 no gi bend pipe, with 2nos of pole clamps with bolts and nuts, 32 / 40 mm 1 no gi bend pipe, with 2nos of pole clamps with bolts and nuts, 6amps to 32 amps sp mcb, fuse unit 32 amps 415v , fuse unit 63 amps 415v , main switches spn 32 amps 2 pole , main switches tpn 32 amps , main switches tpn 63 amps , automatic on/off street light timer switch with 24hrs 7 days programable digital timer clock, 40 amps 4 pole contactor with coil, mcb switch and connector fully wired with all accessories, street light meter/main box with wooden board, main switch, fuse carrier fully wired with all accessories, electronic 7 days 24 hrs programable ditial timer clock, 63 amps 4 pole contact with coil, 9w led bulb, 36w 4 pin non retrofit type cfl power saver lamp, 36w 4 pin non retrofit type cfl power saver choke, 20w high bright led 4 feet light, 20w led power saver street light fitting, 25w led power saver street light fitting, 30w led power saver street light fitting, 36w led power saver street light fitting, 50w led power saver street light fitting, 150w led power saver flood light fittings, 200w led power saver flood light fittings, 40w all-in-one solar led street light fittings, 60w all-in-one solar led street light fittings, 80w all-in-one solar led street light fittings, 18w to 25w led chip board, 30w to 36w led chip board, 45w to 60w led chip board, 72w to 90w led chip board, 120w to 200w led chip board, 18w to 25w led heavy duty electronic driver, 30w to 36w led heavy duty electronic driver, 45w to 60w led heavy duty electronic driver, 72w to 90w led heavy duty electronic driver, 120w to 200w led heavy duty electronic driver, 10 kv surge protector, 48` ceiling fan with all accessories, 10metre hot dip galvanised octogonal pole with round ring arm and 4nos of strong 5feet anchor bolts, templates, and nuts etc.. complete set, 16 amp mcb, service charges automatic on/off street light timer switch box , service charges for mini mast lighting system, service charges for high mast lighting system, ec mcb 40 amp, 7/16 wire coil (copper)
Tender For corrigendum : tender for supply of solar pv panel topcon - 15 kw , grid connected inverter/ power conditioning unit (pcu) alongwith built-in meter , module mounting structure (mms) , structure accessories , net meter and solar meter , array junction box , dcdb , acdb , string and jumper , earthing and cable , lighting arrestors , lighting protection system (lps) , surge protection device (spds)- surge arrestor , connectors , conduits and pipes. , dc cable for string and jumper , power cable from inverter to acdb , power cable for earthing - 15 kw , ac armored aluminum cable - 15 kw , installation , testing and commissioning - 15 kw , grid islanding protection as per nit , danger boards & signages as per nit , fire extinguishers as per nit
Tender For repair and maintenance of earthings, lighting protection system and miscellaneous e/m assets and other allied works at army area under ge (a) no 1 jodhpur
Tender For corrigendum : supply and deliver of street lighting materials for west constituency maintaince and supply to electrical stock point at llr in guntur municipal corporation.-- 110w led street light , 130w led pcbs , 150w led drivers , 180w led pcbs , 200w led pcbs , 20w led drivers , 20w led pcbs , 35w led street light , 36w led drivers , 36w led pcbs , 45w led street light , 6 sqmm (1 coil = 90 rmt) , 70w led drivers , 70w led pcbs , 70w led street light , supply and delivery of following pcbs of led street lights fixtures makes of standard company. as per local quotations , supply and transportation of led driver as per is 15885 (part 2/sec 13) 2012 with input line voltage 120v-270v ac, 50hz with surge protection more than 2.5 kv, ip20, suitable for led indoor luminaire, with 2 years warranty. makes: as per list of recommended brands. as per local quotations , supply and transportation of led street light luminaire made of pressure diecast aluminum body with powder coated, having protective toughened glass, supply input voltage 120-270v ac, p.f > 0.90, high power leds having system efficacy >= 120 lumens/watt and junction temperature < 70°c, with ingress protection ip66, luminaire performance complies to is 10322 (part 5/sec-3), driver surge protection 4kv, in-house additional surge protection 10 kv with optics distribution, thd<10% at 110 volts ac, driver efficiency >90%, cct: 3000k-5700k, minimum cri>70, etc., complete with earth connection and not less than two years warranty. makes: as per list of recommended brands / halonix halonix,bajaj,havells,crompton , supply and transportation of led street light luminaire made of pressure diecast aluminum body with powder coated, having protective toughened glass/temperature protective polycarbonate diffuser, supply input voltage 120-270v ac, p.f > 0.90, high power leds having system efficacy >=120 lumens/watt and junction temperature < 70°c, with ingress protection ip66, luminaire performance complies to is 10322 (part 5/sec 3), driver surge protection 4kv, in-house additional surge protection 10 kv with optics distribution, thd<10% at 110 volts ac, driver efficiency >90%, cct: 3000k-5700k, minimum cri>70, etc., complete with earth connection and not less than two years warranty. makes: halonix,bajaj,havells,crompton , supply of isi marked wpsc (weatherproof twin core) isi aluminum wire. makes: as per list of recommended brands ssr 2025-26 elec-1.6.2
Tender For corrigendum : supply and deliver of street lighting materials for east constituency maintaince and supply to electrical stock point at llr in guntur municipal corporation- 10.00 sqmm (1 coil = 90 rmt) , 110w led street light , 130w led pcbs , 150w led drivers , 180w led pcbs , 200w led pcbs , 20w led drivers , 20w led pcbs , 35w led street light , 36w led drivers , 36w led pcbs , 45w led street light , 6 sqmm (1 coil = 90 rmt) , 70w led drivers , 70w led pcbs , 70w led street light , supply and delivery of following pcbs of led street lights fixtures makes of standard company. as per local quotations , supply and transportation of led driver as per is 15885 (part 2/sec 13) 2012 with input line voltage 120v-270v ac, 50hz with surge protection more than 2.5 kv, ip20, suitable for led indoor luminaire, with 2 years warranty. makes: as per list of recommended brands. as per local quotations , supply and transportation of led street light luminaire made of pressure diecast aluminum body with powder coated, having protective toughened glass, supply input voltage 120-270v ac, p.f > 0.90, high power leds having system efficacy >= 120 lumens/watt and junction temperature < 70°c, with ingress protection ip66, luminaire performance complies to is 10322 (part 5/sec-3), driver surge protection 4kv, in-house additional surge protection 10 kv with optics distribution, thd<10% at 110 volts ac, driver efficiency >90%, cct: 3000k-5700k, minimum cri>70, etc., complete with earth connection and not less than two years warranty. makes: as per list of recommended brands / halonix halonix,bajaj,havells,crompton , supply and transportation of led street light luminaire made of pressure diecast aluminum body with powder coated, having protective toughened glass/temperature protective polycarbonate diffuser, supply input voltage 120-270v ac, p.f > 0.90, high power leds having system efficacy >=120 lumens/watt and junction temperature < 70°c, with ingress protection ip66, luminaire performance complies to is 10322 (part 5/sec 3), driver surge protection 4kv, in-house additional surge protection 10 kv with optics distribution, thd<10% at 110 volts ac, driver efficiency >90%, cct: 3000k-5700k, minimum cri>70, etc., complete with earth connection and not less than two years warranty. makes: halonix,bajaj,havells,crompton , supply of isi marked wpsc (weatherproof twin core) isi aluminum wire. makes: as per list of recommended brands ssr 2025-26 elec-1.6.2