Tender For corrigendum : custom bid for services - verification and health checking of bently-nevada make turbine differential expansion etc of ctps u7 during the coh-01) health checking verification, replacement if any, refitting & commissioning of:- a) all bearing and shaft vibration sensors and related modules of turbine/generator bearing. b) lpt differential expansion sensors and related modules at turbine brg no.-4. c) axial shift sensor and keyphasors sensors. d) bearing vibration sensors and keyphasors and its related modules of id fans, fd fans, coal mills, pa fans, cw pumps, ceps and bfps. e) all the cables associated with the above measurements. f) work related to running unit 8 ctps as per availability of work front and up to extent possible. 02. preparation of documentation like verification report of sensors and modules. 03. work assistance:- the entire job is to be carried out by m/s ge oil & gas india private limited. however, dvc will provide work assistance of technicians and helpers to carry out the said jobs. 04. any special tools like shacker table, tk 3e or other equipment s require for the execution of the above mentioned job, especially for lp turbine deferential measurement system are to be brought by m/s ge oil & gas india private limited. 05. all the spares will be provided by dvc..
Tender For genl store items > - genl store items, {cutting tool}angle grinding cutting wheel size:4"(wt0020), {cutting tool}angle grinding wheel 4" ag4(wt0018), {cutting tool}angle grinding wheel ag-7"(wt0062), {misc. / general store a/c}araldite resin with hardener 1.8kg(standard epoxy adhesive)(gn0081), {packing & jointing / packing material}asbestesrope 1/8"(3mm)(pk0040), {cutting tool}buffing grinding wheel ag-4(wt0040), {cutting tool}buffing grinding wheel ag-7(wt0066), {misc. / general store a/c}cotton waste coloured(gn0024), {cutting tool}cutting grinding wheel ag-7"(wt0030), {misc. / general store a/c}emery paper(sp0141), misc. / general store a/c}emery paper fine(sp0145), misc. / general store a/c}emery paste fine(sp0143), {misc. / general store a/c}emery pate rough(sp0082), {misc. / general store a/c}emery tape(sp0142), {packing & jointing / packing material}graphite packing (gland packing n/m) 16mm(5/8")(pk0016), {misc. / general store a/c}graphite paste(sp0160), tool& tackle store a/c}grease gun 5kg(tt0160), welding store a/c}hand glaues leather 14"(wm0016), {misc. / general store a/c}holdtite 500gm threaded pipe sealant(sp0209), {cutting tool}hss hand hexa blade 12"*1/2"*0.025"(sp0212), welding store a/c}l.p.g gas regulator(wm0001), {misc. / general store a/c}locktite-495(sp0735), misc. / general store a/c}locktite-638(sp0737), misc. / general store a/c}marking cloth(gn0096), {oil & lubricant}molycot hot paste 1000(ol0024), {tool& tackle store a/c}oil keep 1/2ltr.(gn0117), misc. / general store a/c}old dhoti(gn0121), misc. / general store a/c}painting brush 4"(gn0138), {misc. / general store a/c}painting brush 5"(gn0139), {welding store a/c}regulator oxy.(wm0002), {rubber part}rubber joint sheet 3mm (1/8")(pk0025), {rubber part}rubber joint sheet 6mm (1/4")(pk0026), {misc. / general store a/c}spherical round brush 6mm(gn0381), {misc. / general store a/c}spherical round brush 8mm(gn0382), packing & jointing / packing material}steam joint packing lp (n/m )1/8" , 3mm(pk0023), packing & jointing / packing material}steam joint packing lp (n/m) 1/16" 1.5mm(pk0022), {packing & jointing / packing material}steam joint sheet lp(n/m) 1/32"(0.75mm)(pk0021), {mill house spare store a/c}taflon hydex coupling no-48(sp1162), {misc. / general store a/c}teflon tape 3/4" 1"(sp0357), {welding store a/c}welding cable copper(wm0025)capacity - 600amp, {welding store a/c}welding gas cutting copper nozzle 1/16"(wm0012), {welding store a/c}welding gas cutting copper nozzle 1/32"(wm0010), {welding store a/c}welding gas cutting copper nozzle 3/64"(wm0083), welding store a/c}welding gas cutting torch (cutter)(wm0008), {welding store a/c}welding glass black(wm0022), {welding store a/c}welding glass white(wm0023), welding store a/c}welding hand screen(wm0027), {welding store a/c}welding head screen(wm0004), {welding store a/c}welding holder 600amp(wm0021), {misc. / general store a/c}wire brush(gn0202), {iron & steel store a/c}high carbon (en-45) spring steel flat 12x75mm(is0022), {iron & steel store a/c}ms en-8 square bar 65mm(is0136), {mill house spare store a/c}polyster slings for rope coupling(sp1334)
Tender For annual contract for housekeeping and equipments cleaning at pps iii bawana - contract for housekeeping & equipments cleaning at pps-iii bawana for three months, clng entire flr area gt#1&2, dusting wall door window gt#1&2, washing flr gts&around, gt accries coment floor & encloser 1&2, dusting clng structural member gt#1&2, clng ent flr ar gt#1&2 air inl fil house, clng entire flr area sos 1&2 ,jop 1&2, clng entire flr area gcs 1& 2, clng entir road ,drain around gcs 1&2, dusting clng structurl membr gcs 1&2, clng entire flr area of et,pt,gbdpu, dust clng wall door win around pt,gbdpu, generator & gcb flr of unit#1 &2, clng entire flr area of exciaon room1&2, dust clng wall door win of exci room 1&2, cln enti flr area of hydn room 1&2,stg 1, dust cln wall dr wn of hyd rm gt1&2,stg1, clng entire flr area of dmcw & phe room, dust cln wall ,dr wind of dmcw & phe rm, cln enti(gtgt1&2&stgt#1)sat1&2, lt tr ar, clng entire flr area of package ac room, clng entire ground area dsb, dusting wall door window dsb, clng entire ground flr area hrsg i&ii, clng drains & roads around hrsg i&i, washing roads around hrsg i&ii, cln enti flr from gf to 3rd flr bfp bldg, clng drain & road around bfp bldg, cln ent flr ar stg hall bldg, mot&gd flr, dusting clng structural member stg hall, clng entire flr area of control room, dust cln cab wall dr wind of conl room, clng entire flr area of battery room, clng enti flr ar of cable gallery room, clng entire flr area mcc room, dusting clng structural member mcc room, clng entire flr area of nn100 room, clng entire flr area chiller room, clng entire flr area of lp co2 tank, cln toilet near by gas turbine, clng entire flr area comp house, dust clng door window., clng entire flr area of fire pump house, dust clng door window., clng entire areas of cwpp house, clng entire flr area rwr pp house, clng entire flr area gcs, clng entire flr area cooling tower &stai, gf flr i/c staircase upto ff flr, dusting clngs door window ceiling gf, 1st flr flr i/c staircase upto 2nd flr, dusting clng door window ceiling 1st flr, parking place and internal road, clean toilet, clng entire flr area gf, dusting clngs door window ceiling gf, clean toilet, clng gas turbine compartment, clng vent fan & its motor gt#1&2, cln gt accs compartment equipments 1&2, clng eqipts &pipe in so s1&2 ,jop 1&2, cln eqts &pipe gcs1&2(near gas turbine), clean bus duct & its support of gt#1&2, clng generator & gcb of unit#1 &2, clean dg set & fuel tank, cln auxs( pump, motors, pip, v/v etc), cln steam tur1& its associated aux ., clng stg 1 generator, exci encl,bus d, cln stg stm,oil,wt, pips on stgfr,motfr, cln ecw,acw,sos,vacm pp,cep mots ,v/v, clean compressor , pipe, v/v,dryers,tank, clean fire pump, motor, pipe,v/v, clean cw& acw pump, motor, pipe,v/v, clean raw water pump, motor, pipe,v/v, clean gcs (near gail terminal) eqts,v/v, clng lci enclosure from outside, clng entire flr area gt#3&4, dusting wall door window gt#3&4, gt acces compar floor&enclos3&4, washing flr gts&around, dusting clng structural member gt#3&4, cln enti flr area gt#3&4air filter house, clng entire flr area sos 3&4 ,jop 3&4, clng entire flr area gcs 3&4, clng entir road ,drain around gcs 3&4, dusting clng structurl membr gcs 3&4, clng entire flr area of et,pt,gbdpu, dust clng wal dr windo aroud et,pt,gbdpu, generator & gcb flr of unit#3&4, cln entir flr area of exciation room3&4, dust cln wal dor windo of exciat rm 3&4, cln entr flr area of h2 rm 3&4,stg 2, dust cln wal dor of hyd rm gt 3&4,stg 2, cln entr flr area of dmcw & phe room#2, dust cln wall ,dor of dmcw & phe room#2, cln entr road(gtgt3&4, stgt lt trns area, clng entire ground flr area hrsg iii&iv, cln drains & roads around hrsg iii&iv, w
Tender For tender for purchase of various type hardware and miscellaneous items - emery cloth rough make- carborendum or equivalent, emery cloth fine make- carborendum or equivalent, emery tape rough, width- 2 , make- carborendum, emery tape fine, width- 2 , make- carborendum, valve lapping compound silicon carbide (rough) cane 400 gm each ( emery paste ) make-carborendum, graphite powder, make- carborendum or equivalent, blue paste tube. make- atlas, araldite (90 gram each set). make- pidilite, rustoline (500 ml each) make- pidilite, hacksaw blade x h.s.s, make-mirinda/l&t/tapria, teflon tap roll, x12 mtrs. make- champion, holdite (hawco,pidilite) 500 gram each, bearing retainer anabond-412, m-seal rasin base and hardner, make-pidilite/ anabond, rubber hose pipe wire braided 1 , make-dunlop/indomakson/uroflex, gi hose clamp make- klipwell, gi hose clamp 1 make- klipwell, premium dura welding hose pipe, size-8 mm brusting pressure 50 kg/cm2, colour- red, make-essab, welding cable (lead) 600 amp, 2200 copper wire, make- essab, brass nozzle for l.p gas size 1/16 make- asha, sunshine., brass nozzle for l.p gas, size 3/64 make- asha, sunshine, welding holder 600 amp, make- essab, welding hand gloves. make- essab, welding hand screen make- essab, black welding glass, make- germany, welding goggales . best quality, plain goggle. best quality, oxygen gas regulator make: essab, lp gas regulator make: essab, gi hose clamp 12 mm . make- klipwell, cotton waste.best quality, old dhoti (full long ), m.s. short bend c class size 1/2 thick- 4 mm 3d, m.s. short bend c class size 3/4 thick- 4 mm 3d, m.s. short bend c class size 1 thick- 4 mm 3d, m.s. short bend c class size 2 thick- 4 mm 3d, m.s. short bend c class size 2-1/2 thick- 4 mm 3d, m.s. short bend c class size 3 thick- 4 mm 3d, m.s. short bend c class size 4 thick-5 mm 3d, m.s. short bend c class size 6 thick-5 mm 3d, m.s. short bend c class size 8 thick-6 mm 2d, m.s. short bend c class size 10 thick-6 mm 2d, m.s. long bend c class size 1/2 thick- 4 mm 3d, m.s. long bend c class size thick- 4 mm 3d, m.s. long bend c class size 1 thick- 4 mm 3d, m.s. long bend c class size 1-1/2 thick- 4 mm 3d, m.s. long bend c class size 2 thick- 4 mm 3d, m.s. long bend c class size 2-1/2 thick- 4 mm 3d, m.s. long bend c class size 3 thick-4 mm 3d, m.s. long bend c class size 4 thick-6.85 mm 3d, m.s. long bend c class size 5 thick-6.85 mm 3d, m.s. long bend c class size 6 thick-6.85 mm 3d, m.s. long bend c class size 8 thick-7.85 mm 2d, m.s. long bend c class size 10 thick-7.85 mm 2d, m.s. long bend c class size 12 thick-7.85 mm 2d, m.s. flange table d size -3/4 , m.s. flange table d size -1 , m.s. flange table d size -1-1/2 , m.s. flange table d size -2 , m.s. flange table d size -3 , m.s. flange table d size -4 , m.s. flange table d size -5 , m.s. flange table d size -6 , m.s. flange table d size -8 , m.s. flange table d size -10 , m.s. flange table d size -12 , roll guard grease (ptpe rain force energy saver), c s socket welded gate valve class-800 size 25 mm make:ksb/leader/uniklinger, c s socket welded gate valve class-800 size 40 mm make:ksb/leader/uniklinger, c s glove valve class-800 size -25 mm make:ksb/leader, seamless long band schedule -80 size 20 mm make: msl/jsl 3d, seamless long band schedule -80 size 25 mm make: msl/jsl 3d, seamless long band schedule -80 size 40 mm make: msl/jsl 3d, seamless long band schedule -80 size 80 mm make: msl/jsl 3d, seamless long band schedule -80 size 65 mm make: msl/jsl 3d, seamless long band schedule -80 size 150 mm make: msl/jsl 3d, seamless long band schedule -80 size 200 mm make: msl/jsl 3d
Tender For supply of liquefiedpetroleumgas, type : commercial butane- propane mixture,confirming to is:4576-1999 (second revision) with amendment no 1 of m ay 2003 (reaffirmed 2009) edition 3.1 (2003-05) in 19 kgs cylinders. specn: cylinders. [ warranty period: 30 months after the date of delivery ]
Tender For corrigendum : providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - industry unit; contract for inspection, repair & high speed dynamic balancing of lp turbine rotor of synthesis gas compressor unit in ammonia plant at rcf thal; buyer
Tender For corrigendum : supply of domestic gas stoves for use with liquefiedpetroleumgases as per is 4246 (q3) , electric water heater - geyser (v2) as per is 2082:2018 (latest) (q3)