Latest looking glass Tenders | Government looking glass Tenders

corporations/Associations/Others

CTN :45492328

24 Jun, 2026 30.85 Lacs

Sonbhadra - Uttar Pradesh

Tender For supply of , taflon gland rope seal oil valve size 4x4 sqmm , taflon gland rope seal oil valve size 6x6 sqmm , taflon gland rope seal oil valve size 8x8 sqmm , taflon gland rope seal oil valve size 10x10 sqmm , m s coupling bolt for dc seal of oil pump full thread , galvanized ht nut bolt with 2 nut 2 flat washer 1spring washer 12x75 mm pitch 1point 5 mm full thread , nipple for h2 gas filling regulator 36x34mm brass make , o ring of size od 50mm id 44mm thick 3mm , o ring of size od 52mm id 44mm thick 4mm , o ring of size od 55mm id 45mm thick 5mm , o ring of size od 60mm id 54mm thick 3mm , copper pipe id 5mm od 8mm length 2mtr , copper washer id 8mm od 14 mm thickness 2mm , industrial h2 gas filling pipe reinforced by wire mesh id 10mm od 16mm , oil gauge glass set with fitting for hydraulic tank , industrial grade h2 gas filling regulator for a generator of a 200mw unit inlet pressure 125 150kg cm2 outlet pressure 3 4kg cm2 safety and testing as per peso guidelines , perplex container for 15 75 kv bus duct complete set , portable hydrogen gas leak detector , brass make hexagonal nut for h2 filing post valve , caf jointing sheet 59 oil 1 0 mm 1x2 meter , ms coupling bolt for ac seal of oil pump full thread , dc seal oil pump rpm 2900 head 120m complete mechanical seal set single inside , ac seal oil pump rpm 2900 head 120m complete mechanical seal set single inside , 1cx2 5 sq mm 1 1kv grade single core cu conductor pvc bundle of 90m red yellow blue insulated wire as per is 694 make havells , ss 304 bolt with 2 nuts 2 flat washers 1spring washer 12 5x70 half thread , handheld insulation tester megger 1kv type rechargeable make megger , digital multimeter , roller bearing no 306 , caf jointing sheet 59 oil 2 0 mm 1x2 mete , caf jointing sheet 59 oil 3 0 mm 1x2meter , caf jointing sheet style 54 n m 0 5mm 1x2 meter , caf jointing sheet style 54 n m 1 5mm 1x2 meter , brass bolt with fixed washer and 1 flat washer for slip ring carbon brush size 6x12mm , brass make extension nipple for h2 post valve , brass make hexagonal nut 2 flat washers and 1 spring washer for the co2 filling post valve , brass nut bolt and 1 no fixed and 1 no flat washer for slip ring 8x35mm , brass plug for h2 gas cooler , brass plug for seal oil cooler , brass strip for slip ring carbon brush holder 17x47x1 soft metal as per sample , insulating flat washer made of glass textolite 5mm thick id 10mm od 26mm , insulating flat washer made of glass textolite 5mm thick id 12mm od 28mm , insulating flat washer made of glass textolite 5mm thick id 18mm od 40mm , insulating flat washer made of glass textolite 5mm thick id 22mm od 44mm , insulating flat washer made of glass textolite 5mm thick id 24mm od 48mm , insulating flat washer made of glass textolite 5mm thick id 26mm od 50mm , insulating flate washer made of glass textolite 5mm thick id 28mm od 52mm , insulating fiber sleeve having dimension id 10mm od 13mm length 2mtr , insulating fiber sleeve having dimension id 12mm od 16mm length 2mtr , insulating fiber sleeve having dimension id 16mm od 20mm length 2mtr , insulating fiber sleeve having dimension id 20mm od 25mm length 2mtr , insulating fiber sleeve having dimension id 8mm od 11mm length 5 mtr complete pipe without a cut , insulating fiber glass sheet size 1x2 mtr and thickness 5mm , ss bolt 12 5x80mm half thread thread and micro pitch with following size 12 5x80 mm , ss bolt with 2 nut 2 flat washer 1spring washer having micro thread and micro pitch with following size 12x80 mm , ss bolt with nut and 2 no flat washer and 1 no spring washer having micro thread and micro pitch with //bid details 2 / 93 following size 36x70 mm , bimetallic strip 100x50 mm , gun metal make carbon brush holder for generator , pvc hose pipe 1 point 25inch , hydraulic tank looking glass looking glass transparent toughened heat resistant up to 300 deg c glass thickness 14mm moc toughened glass with sealing , damper tank looking glass looking glass transparent toughened heat re

Central Government/Public Sector

CTN :45477670

16 Jun, 2026 NA

Visakhapatnam - Andhra Pradesh

Tender For procurement of looking glass assembly for esp hvr disconnecting switchat ntpc lara

CTN :45368784

20 Jun, 2026 NA

Haridwar - Uttarakhand

Tender For empanelment of vendors to provide furniture items on rental basis during the kumbh 2027-haridwar - almirah steel almirah: 4 sections: 6x3, almirahsteel almirah: 3 sections: 4x3, almirah hanging almirah: 6x3, almirah small steel almirah 4x2.5, bed single bed: folding, steel frame, plastic newad knit: 6x3, bed dewan bed simple with mattress 3-4" thick, bed dewan bed box type with mattress 3-4" thick, bed double bed sunmica top including mattress 3-4" thick, bed single bed sunmica top including mattress 3-4" thick, bedsheet colorful/white/printed bedsheet single bed, bedsheet colorful/white/printed bedsheet double bed, bench bench with arm rest steel frame with wooden seat and back, bench wooden bench with armrest 3 seater, bin dustbin for rooms small 5-10 ltr, bin dustbin big for waiting room10-50 ltr, blanket cotton blanket 250 gsm, blanket blanket 500 gsm single bed, blanket blanket 500 gsm double bed, blanket blanket 300 gsm single bed, blanket blanket 300 gsm double bed, busket balti/bucket 20 ltr, cash box iron/aluminium cashbox, chair plastic chair: moulded, with armrest, chair steel chair: padded back and seat, with armrest, chair steel chair: padded back and seat, without armrest, chair revolving chair (basic): padded back and seat, with armrest, chair revolving chair (executive): padded back and seat, with armrest, chair presidential chair: for vips seated on stages, chair office chair with arm rest, chair chair- folding , steel/wooden, cover table cloth, cover chair cover, cover sofa cover, curtain plastic sheet curtain to prevent dust to enter areas with installation (different sizes), display display board 10x4, doormat doormat, dressing dressing table with stool: 4 mirror, dressing dressing table with stool: 3 mirror, drum drum 200 ltr, drum drum 50 ltr, frill table frill, glass looking glass: 1x1, hospital hospital bed: 6.5x3, hospital folding stretcher, hospital surgical tray, hospital wooden examination table, hospital medicine counter: table with one tin above and one below 3x3, hospital bed side locker, kaleen kaaleen 6x9, masnad masnad with cover 6kg cotton, mattress cotton mattress 3kg cotton 3x6, mattress dunlop mattress 2"thick, mattress dunlop mattress 4"thick, mug mug, pelmet pelmet fitting as required with curtain hooks, pillow cotton pillow with cover 1kg cotton, pillow dunlop pillow with cover, platform flooring (wooden): providing and laying wooden flooring as required which will be fixed to 18/19 mm thick ply which is further fixed to wooden batten in both the direction (9" height), rack steel rack: 3 compartments, safe safe: 2x2x2, sofa special sofa set wooden/steel frame with spring cushioning and centre table with sunmica/ glass top 4x2, set of 3 piece- (3+1+1) 5 seater, with armrest, sofa sofa set wooden frame with dunlop cushioning and acrylic cloth covering and centre table with sunmica/ glass top 4x 2, set of 3 piece- (3+1+1) 5 seater with armrest, sofa sofa single seater wooden frame with dunlop cushioning and acrylic cloth covering, sofa sofa 2-seater wooden frame with dunlop cushioning and acrylic cloth covering, stand towel stand aluminium/steel, stool bath stool: 2x2, 6" high, wooden/plastic, stool wooden stool: sunmica top, table wooden executive table: laminated top, side rack and drawers: 6x3, table wooden executive table: laminated top, side rack and drawers: 5x3, table wooden executive table: laminated top, side rack and drawers: 4x3, table secretariat table: sunmica top with 3 drawers: 5x3, table secretariat table: sunmica top with 3 drawers: 4x3, table centre table: sunmica top and steel/wooden frame: 4x2, table conference table : 8x2, table dining table: sunmica top with 6 chairs: 5x3, table dining table: plastic with 6 chairs: 5x3, table table: sunmica top: 4x3, table tea table: sunmica top steel frame : 2x3, table centre table : sunmica top and steel frame: 3x1.5, table centre table: plastic: 3x1.5, table side table sunmica top 15"x15", table folding table steel frame and wooden

CTN :45322644

01 Jun, 2026 8.70 Lacs

Sawai Madhopur - Rajasthan

Tender For supply, installation, testing and commissioning of phase wire and street light and vairious electrical equipment needed for implementation of budget announcement 2025-26 - providing & fixing of ik08, ip 66 protected led street light luminaire on existing bracket/pole. fixture made of powder coated single piece pressure die cast aluminum material with heat dissipation fins on housing with uv stabilized pc (uv stablization report submitted for uv cover ) /toughened glass cover and secondary lens on each led & should be smd type of 3 to 5 watt each . the system efficacy >=125 lm/ wt and potted driver & has a unique bis r number with input voltage ac 120 to 270 v ac with high voltage cutoff @>=300 v ac and auto resetting safety , power factor >0.95 driver efficiency >85% ,thd(i) 70 and cct 5700k +355k. surge protection shall be min 4 kv internal and min 10 kv external inside driver compartment. driver should be phase to phase protection of 440 v for 4 hrs. manufactures word mark/name engraved/embossing on die cast housing to allow traceability/authenticity. fixture shall be as per is 10322 complianced.oem must have its own in, led street light fixture with minimum lumen output 5600 lm, sitc of ip-42 and general construction confirming to is:8623 : 1993, wall/ free standing floor mounted dust and vermin proof compartmentalised cubical panel as specifications and other parameters required as per point (a) ,(b), (c),(d), (e), (f), (g), (h) as below:-(a)thickness of crca sheet shall be 2.0 mm, cable alley compartments having concealed hinged type doors with key type lock with / without detachable extension type structure. removable 3 mm. thick sheet steel gland plates with appropriate size of knockouts for cables shall be provided(b)complete panel shall undergo a process of degreasing, water rinsing, activation, derusting, pickling in acid bath, phosphatising & shall be subjected to nine tank process and then powder coated with approved shade of minimum 70 microns on both side of panel. the panel having pe foam/ neoprene rubber gasket of not less than 3mm thickness ,required hardware , concealed hinged door with key type locking arrangement for equipment/switchgear earthed with 2.5 sq.mm braided copper wire.[c) interconnection between bus bar and switchgears /cable shall be rigidly supported and made out by flexible copper wires (up to 63 amp ) and by solid bus bar (>63 amp ) . control wiring will be carried out with 1.5 sq.mm, earth wire with 2.5 sq.mm and ct with 2.5 sq.mm flexible copper wire only. all joints / interconnections of copper bus bar shall be dully tinned . clearance between main bus bar and risers / metal parts shall be at least 10 mm additional to width of bus bar bus bar is insulated by heat shrinkable sleeves . earth and neutral bus bar shall be half of the size of phase bus bar. ( cost of bus bar / flexible wire for interconnection between main busbar and switchgear is to be paid extra )(d)wiring between components within switchgear and incoming / outgoing cable shall be done through the terminal block only. direct connection shall not be permitted. each terminal block shall be one piece moulded, barrier type, 650 volt grade, complete with washers, heads, studs with two nuts and identification strips and shall have adequate continuous current rating. for tap-offs, adjacent terminals with shorting strips shall be used. 10% spare terminal blocks shall be provided. wire identification on marking strip shall correspond to the designation of the wiring diagrams. all wire terminals on the equipment shall also be marked with designation corresponding to those of the wiring diagram.(e)all wiring shall be enclosed in plastic channels and neatly bunched and closed in metering chamber, wiring between terminals of various devices shall be point to point (no wire splitting or tee connections) with wires neatly trucked along the back of the panels, adequately supported to prevent sagging.(f)floor mounted panel sh

Central Government/Public Sector

CTN :45267787

02 Jun, 2026 NA

Ranchi - Jharkhand

Tender For supplying items big towel , small towel , grass mate , rubber mat , seat cover , curtain set , pav dani , bumper (rear) , car fastener , duster , towel belt , flag , flag rod , wiper blade , body polis , deck board polish , back rest , hand rest , looking glass , light bulb , star plate frame , number plate frame , star , star plate cover , head rest , steering cover , fog light , tire polish , door visor , vehicle mobile charger , to lose , cut out , wheel cap , dax word fashioner , ac freshener , black heat , colleen , car shampoo , chakka rich , jack

CTN :45228398

30 May, 2026 NA

Birbhum - West Bengal

Tender For procurement of bottom ash and wet ash spares for overhauling of unit 3 under ahp mm - nozzle for air washer (dry for fly ash system size: 5 mm dia,for ahp-ii, nozzle with insert # tip dia 9 mm of insert,moc-ss 410 (nozzle),ceramic,hardness 7708 mohs,ahp-i# for 10in wetting head,make-dcips,pn-6,7, inlet section fr wetting head10" of ahpi ( one side bevelled and others side plain (b/p),after 90 degree 10" elbow for wetting head. moc: durite 450bhn ), adaptor for collector tank ( one side bevelled and others side flanged with holes. mat: durite 450bhn ), adapter b/b # for ahp-i,below wetting head# for collection tank ( both sides bevelled. mat: durite 450bhn ), tail piece after combining tube,ahp-ifor ba slurry line,make-dcips ( one side bevelled and others side plain (b/p),after combining tube. moc: durite 550bhn ), complete assembly of jet pulsion p/p moc: durite 550 bhn for body,ss-410 for nozzle tip,ceramic 7 moh min for nozzle insert,cap.-60 t/h,pr.-10 kg/cm2 for ahp-i, combining tube # dcips make-dcips,part no.-1,moc: durite,550 bhn,for ahp-i ( hydrostatic test pressure at shop: 9 kg per sq cm (g). ), drain pit jet pump,ejector type # complete assy with water inlet elbow,pipe with flange,bolts and nuts and foundation bolts ( discharge rate of 35 # 50 cubic mtrs. / hour, horizontal distance of 150 # 160 mtrs with an elevation of 10 mtrs from gound level (0.00 mtrs), sump volume : 45 cubic mtrs. one no. orifice for discharge line with each of ejector jet pump is required with other accessories. ), ba hopper,feed sump/chute for bottom ash hopper, nozzle # of seal trough,for ba hopper,ahp-i# for ba hopper,ahp-i ( nozzle with holder. ), inspection window assembly looking glass dia 224 mm th 12 mm for ahp-ifor ba hopper, inspection window glass,200m # ( moc: borosilicate glass. ), shaft sleeve for clinker grinder for make-ucc/dcips,pno. 15 moc ss 410, 350 bhn, for ahp-i, cambolt,nut,locknut # moc-ss 410(cambolt) heat treated to rc 32-34,metric m 20 coarse a2-70,is 1363 (nut# for ba clinker grinder ( 1set=32 nos 1. moc: ss-420 (cam bolt) heat treated to rc 32-34. metric m20 coarse a2-70, is 1363 (nut). 2. 01 set: ), packing gland follower # moc: bronze ltb-2 is 318,for ahp-1 ( for ba excen crusher 1. part no.-12 2. moc: bronze, ltb:2 is:318 ), labyrinth ring of bearing housing moc-ms is 2062,for ahp-ifor clinker grinder,make-dcips ( for ba excen crusher 1. part no.-13 2. moc: ms is 2062 gr-a. ), chain # no of link-118,for ahp-i ( for clinker grinder of ahp-i. no of link: 118. ), small size sprocket for ahp-1 bktpp for gear box,for ahp-i, packing gland housing # moc: ci fg 220 is: 210,for ahp-i ( for ba excen crusher 1. part no.-9 2. moc: ci fg 220 is: 210. ), slinger for bottom ash crusher dcips moc-ms,is:2062 gr-a,drawing no 25p06-t-1b-582 ( for ba excen crusher 1. part no.-14 2. moc: ms is 2062 gr-a. ), cam for clinker grinder # heat treated & normalised for ahp-i# for moc:hi chrome alloy with 22% to 27% cr, gate face of feed gate # moc-ss 316 for ahp-i ( moc: ss - 316. including m12x65, csk hd soc. cap bolt, nut, washer. ), adjustable seating wedge # moc-ms,is:2062 gr-a for-ahp-i ( for feed gate. moc: ms, is: 2062 gr a. ), roller # moc-steel.is:1030 for-ahp-i ( for feed gate of ba crusher. moc: steel, is: 1030. ), gland follower for indicator rod dcips of feed gate, ahp-i, guide angle l.h # moc-ms,is:2062 gr-a for-ahp-i ( for feed gate ), guide angle r.h # moc-ms,is:2062 gr-a for-ahp-i ( for feed gate ), indicator rod # moc-s.s,size: 21mm dia.(solid) and 1400 mm long with both ends threaded and nuts,stg-i# for bottom ash hopper feed gate

CTN :45261653

04 Jun, 2026 35.0 Thousand

Sitapur - Uttar Pradesh

Tender For supply of combination plier 8inch tapariya make , screw driver star plain 12inch tapariya make , pt bulb 100 watt 240v surya make , cotton tape1inchx20meter , glass tape 1inchx50meter , dr back insulting varnish lufta each pack 1ltr , steelgrip self adhesive pvc electrical insulation tape , pt bulb 100 watt 24v , dr back bectrol red each 1 ltr pack , air heater u type 2kw fins type , glass sleeve 10mm , glass sleeve 12mm , crc , glass sleeve 6mm , glass sleeve 2.5mm , empire tape , pt holder 5amp

Central Government/Public Sector

CTN :45255409

15 Jun, 2026 NA

Abu Road - Rajasthan

Tender For supply of pantograph assembly wind shield wiper cab looking glass ls/rs to emd.pt.no.10634581. as per drg.no. emd.pt.no.10634581 [ warranty period: 30 months after the date of delivery ] ]

Central Government/Public Sector

CTN :45077526

18 May, 2026 NA

Delhi - Delhi

Tender For supply of set of looking glass size: 29" x 21" x 5 mm and 26.5" x 15" x 5 mm for train-18 spec. no : is:3438/2023, third revision and quality aa/ssq as per is: 2835: 1987(reaffirmed 2018) third revision. [ warranty period: 30 months after the date of delivery ]

CTN :44933250

06 May, 2026 NA

Kamrup - Assam

Tender For bid to ras supply of boq1 boq1 e e - supply of field toilet block 06 seater relocatabe consisting of all as per techincal specification and store details specified in ser no 1 of a to p and structural steel ser no a to e , deatchable ms steps as per drawing and specification , stainless steel indian water closet iwc s trap thickness 1 point 5mm grade with pvc flushing system and seat cover with all necessary fitting and connection make blue star , stainless steel wash hand basin whb overall size 530mm x 345mm bowl size 457 x 257 x 140 mm all as per technical specification specified in store list , cp towel rod of 18 inch length make isi marked , cp tap weight not less than 450 gm , cp pillar tap for whb weight not less than 450 gm , cp steel soap dish isi marked , plastic cabinet fitted with looking glass of size 1.5 ft x 2 ft with isi marked , 500 ltr capacity sintex tank rectangular tank isi marked 4 layer cover with iron cage as specified and directed , wire pvc insulated cable 1 point 5 sqmm as per technical specification specified in store list , wire pvc insulated cable 2 point 5 sqmn as per technical specification specified in store list , pvc casing capping 20 mm size make topson or plaza or polyplast as per technical specification specified in store list , 5 pin 5 amps switch socket combination with pvc mounting box as per technical specification specified in store list , 11 watt led with lamp as approved to be placed on the wash hand basin as per technical specification specified in store list , 11 watt led with bakelite angle holder shall be provided for the toilet and 01 no each on all four sides as approved as per technical specification specified in store list , power point of 5 pin 15 amp socket and switch combination of modular type as per technical specification specified in store list , exhaust fan of 250mm sweep single phase 230 or 240 volt with shutter make crompton greave or bajaj or havells as per technical specification specified in store list , mcb dp 32 amps conforming to is 2282 to 1996 make crompton greave or bajaj or havells as per technical specification specified in store list , miniature circuit breaker mcb 6 amp to 32 amps single pole make crompton greave or bajaj or havells single pole as per technical specification specified in store list , change over switch 63 amps 3 pole make crompton greave or bajaj or havells as per technical specification specified in store list , high pressure pump one of 2 hp comma high pressure pump with min 100m head as per technical specification specified in store list

Looking Glass Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

corporations/Associations/Others

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector

Central Government/Public Sector