Latest low pressure chemical ionization Tenders | Government low pressure chemical ionization Tenders

CTN :45475071

15 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For purchase of non-consumables for ece department - purchase, dual output regulated dc variable power supply input voltage: 230v/50 hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., function generator frequency range: 0.1 hz to 5 mhz. display: 4 to 6 digit led display. output waveforms: sine, triangle, square, pulse, ramp. amplitude: 0 20 vpp. rise time: 100 ns. distortion: 1% within specified frequency range. power supply: 230 v ac 10%, 50 60 hz. output amplifier protection: short-circuit and 15 v overload protection. dc offset: 0 to 10 v adjustable. attenuation: 0 to 60 db., dso (digital storage oscilloscope) bandwidth: 50 100 mhz. sampling rate: 1 gs/s. channels: 2 (minimum). power supply: 100 240 v ac, 50 60 hz. automatic measurements: vpp, vavg, vrms, frequency, period, vmax, vmin, rise time, fall time, +width, width, +duty, duty, etc. horizontal scale: 5 ns/div 50 s/div or equivalent. vertical resolution: 8 bits (2 channelssimultaneously). vertical sensitivity: 1 mv/div 10 v/div (at input). waveform math: +, , , , invert, fft, etc. waveform storage: 16 waveforms or equivalent. communication interface: usb host and usb interface. display: 7-inch color display or equivalent. input impedance: 1 m 2% || 20 pf. accessories: 2 passive probes (1x/10x)., digital ic trainer kit with breadboard +5 v dc, 1 a regulated power supply. 12 v dc / 15 v dc, 200 ma regulated power supply. solderless breadboard with minimum 840 tie points,power distribution buses. zif (zero insertion force) ic sockets to accommodate 8 or 16 pin ics. logic input and output leds for output monitoring. 16 buffered led outputs. 16 debounced switch inputs. variable clock generator: 0.5 hz to 50 hz. single pulse output: 100 ms (buffered, positive and negative outputs). one seven-segment display with 4 bcd inputs. built-in logic switches. manual clock: debounced push-button (one pulse per press)., lvdt trainer kit ac mains power supply: 230 v 10%, 50 hz. fixed regulated dc power supply: +5 v, 12 v / 500 ma. transducer: lvdt. lvdt displacement: 20 mm (40 mm total). displacement scale: linear 20 mm. displacement display: red color 3 digit led display. excitation frequency: 4 khz. excitation voltage: ac variable excitation voltage up to 5 v., strain guage trainer kit ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. signal conditioning and amplification circuit. instrumentation amplifiers with 3 digit display for strain / output voltage. zero and gain adjustment controls. provision for applying calibrated loads. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual.

CTN :45465678

19 Jun, 2026 NA

Kanchipuram - Tamil Nadu

Tender For supply, installation and testing of electronic equipments - supply -ece lab equipments, single output regulated dcvariable power supply- input voltage: 230v / 50hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., dual output regulated dc variable power supply- input voltage: 230v/50 hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., function generator - frequency range: 0.1 hz to 5 mhz. display: 4 to 6 digit led display. output waveforms: sine, triangle, square, pulse, ramp. amplitude: 0 20 vpp. rise time: 100 ns. distortion: 1% within specified frequency range. power supply: 230 v ac 10%, 50 60 hz. output amplifier protection: short-circuit and 15 v, digital ic trainer kit with breadboard - +5 v dc, 1 a regulated power supply. 12 v dc / 15 v dc, 200 ma regulated power supply. solderless breadboard with minimum 840 tie- points,power distribution buses. zif (zero insertion force) ic sockets to accommodate 8 or 16 pin ics. logic input and output leds for output monitoring. 16 buffered led outputs. 16 debounced switch inputs. variable clock generator: 0.5 hz to 50 hz. single pulse output: 100 ms (buffered, positive and negative outputs). one seven-segment display with 4 bcd inputs. built-in logic switches. manual clock: debounced push-button (one pulseper press)., dc voltmeter(digital) - dc digital voltmeter - 3 digit led/lcd display, measurement range: 0 20 v dc,accuracy: class 0.5( 0.5 % full-scale), dc ammeter - dc ammeter digital - 3 digit led/lcd display, measurement range: 0 5 a dc,accuracy: class 0.5 ( 0.5 % full-scale), lvdttrainer kit - ac mains power supply: 230 v 10%, 50 hz. fixed regulated dc power supply: +5 v, 12 v / 500 ma. transducer: lvdt. lvdt displacement: 20 mm (40 mm total). displacement scale: linear 20 mm. displacement display: red color 3 digit led display. excitation frequency: 4 khz. excitation voltage: ac variable excitation voltage up to 5 v., strain gauge trainer kit - ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. instrumentation amplifiers with 3 digit display for strain / output voltage. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual., ask modulation and demodulation kit - message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. supply voltage (board): +12 v, +5 v dc. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., fpga trainer kit - must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb- uart bridge, usb cable. user manual., measurement scale: a vertical steel meter scale, usually with (1mm) graduations, for precise deflection measurement., accessories: includes a set of slotted weights (e.g., (6times 50g) or similar sets) for incremental loading.

CTN :45270280

10 Jun, 2026 NA

Hyderabad - Telangana

Tender For supply of replacement damped vacuum tank door spring part no 32752 , upgrade kit for damped vacuum tank front door spring assembly part no 32753 , upgrade kit for damped vacuum tank back door spring assembly part no 32754 , load unit water distibutor manifold part no 31622 , load unit air and water manifold part no 31604 , active pirani rough vacuum gauge part no gauge101 , active magnetron high vacuum gauge part no gauge102 , active pirani gauge replacement tube part no gauge101a , supernut assembly part no hn100 , 3 by 4 inch 10 x 8 inch hhb grade 9 bolt part no 33929 , 3by 4 inch flat l9 washer part no hn030 , jack screw for mcu supernut assembly part no hn101a , superbolt lubricant part no hn101b , flat hot grips inch stainless 5mm spring pin 3 point 0mm to 4 point 25mm set of 4 pcs part no 9016 030 , round grips inch full contact stainless steel 10mm set of 4 pcs part no 9065 100 , round grips inch full contact stainless steel 6 mm set of 4 pcs part no 9065 060 , round grips inch partial contact stainless 6mm set of 4 pcs part no 9060 060 , round grips inch partial contact stainless 10mm set of 4 pcs part no 9060 100 , round grips inch full contact cu alloy 6 mm set of 4 pcs part no 9000 060 , graphite foil punch 3 by 4 inch diameter part no tool012 , punch pad for foil punch part no tool011 , automatic specimen loading tool part no 32782 , specimen loading clip for plane strain specimens 10mm x 15mm x 20mm part no 33780 , specimen loading clip for flow stress specimens 10mm diameter x 9mm length minimum part no 33782 , specimen loading clip for flow stress specimens 8mm diameter x 10mm length minimum part no 33795 , specimen loading clip for flow stress specimens 6mm diameter x 9mm length minimum part no 33796 , iso t uniaxial compression anvil cap high temperature part no 9220 069 , low force wedge jaw assembly part no 9510 101 , replacement transducer assembly for 39050 and 39052 jaw to jaw l strain assembly 1 by 2 inch travel part no ga000192 , hydrawedge ii l strain system part no 39057 , cct dilatometer assembly with lvdt transducer part no 9655 001 , universal extensometer mount part no 9655 100 , fine wire thermocouple welder rebuild kit part no 35202 , cct dilatometer tygon tubing 1 by 16 in id x 3 by 16 in od part no tu314 , thermocouple single hole ceramic insulating tubes set of 5 part no tc007 , double hole round ceramic thermocouple insulator part no tc026 , clear teflon tc insulator tubing part no tu010 , black teflon tc insulator tubing part no tu011 , thermocouple red push post part no g176b , thermocouple black push post part no g176c , replacement 110 silicon o ring part no ors110 , normally open dump valve c10 2 cavity part no vlv104 , normally close dump valve c10 2 cavity part no vlv105 , load cell calibrator spherical washer set 0 point 75 inid x 1 point 630 inod x 0 point 38 in thk blk part no wa0750 01

CTN :45238088

08 Jun, 2026 NA

Bangalore - Karnataka

Tender For supply of force transducer for dmta , clamping ring of clamping device for dmta

CTN :45237675

08 Jun, 2026 NA

Bangalore - Karnataka

Tender For supply of triaxial accelerometer 100m v g weight 6 to 8 grams technical spec as per anx i , suitable low noise calbe 30 meter 4 socket 1 by 4 28 unf 4 pf to 3xbnc m and technical spec as per anx vii , triaxial icp type accelerometer 10m v g withstand less than 200 deg c weight 4 to 5 grams technical spec as per anx ii , low noise cable 4 socket miniature type for tri axial miniature type accelerometers anx vii , modal array icp type accelerometer 100m v g weight 5 grams, withstand technical spec as per anx iii , low noise coaxial calbe 30 meter 10 to 32 coaxial plug to bnc and technical spec as per anx vi , icp impedance head acceleration 100m v g force transducer 100mv lb technical spec as per anx iv , low noise cable 30 meter 10 to 32 coaxial plug to bnc plug anx viii , portable vibration calibration icp and voltage inputs frequency range 5 to 10 hz max amplitude 20g 20ips technical spec as per anx v , 64x5 bnc patch panel with trolley as per annx ix , low noise cable 3 meter 4 socket annexue x , low noise cables 5 meter 4 scket annexure x , low noise cables 10 meter 4 socket annexure x , proper storage cases for accelerometer sensors and cables and exciters annexure xi

Central Government/Public Sector

CTN :44703509

04 May, 2026 NA

Surat - Gujarat

Tender For corrigendum : procurement of one off spares of servo level gauges at ongc hazira surat - pcb gps (gause power supply), backplane + transformer, 110v-230v-854atg, pcb spu ii with alarm relays, eeprom programmed for spu 2(density), motor unit, pcb spu-ii, tsi 977 (without keyboard, wall mounted type), measuring drum (27m), including drum, wire and shaft, displacer aisi 316; weight 260g;, max pressure 20 bar, dia - 90 mm, 854 force transducer, drum bearing set including, shaft, -240000455, mpn no: 900027042, o-ring and gasket set (o-ring, set 854 atg), mpn no: 900009591

CTN :44857412

20 Apr, 2026 NA

Gorakhpur - Uttar Pradesh

Tender For supply installation ,testing & commissioning of motorized wire crimp pull tester as per following specification - construction-single column vertical standing supported frame with base plate ,cross -head drive mechanism -ball screw & nut mechanism driven by fixed speed geared motor ,cross head speed range -fixed speed of 50 mm/min ,force transducer -load cell of 1000 kgs. ,force resolution-0.05 kg ,force accuracy- +/- 0.5 % of fsd ,maximum travel-100 mm approx. (between top plate and moving cross head ) , power controls-on/off switch, load controls -tare switch for setting initial reading to zero f/peak switch to view current force or peak force during a test peak clear switch to remove the peak from memory units switch to change measurement units between kg,n and lbs .safety-upper & lower safety limit stops builtin overload safety for load cell protection built in auto stop at sample break ,supply -230 v,50 hz ,1 phase ,grips & fixtures -1 set of hook and pin type arrangement . [ warranty period: 30 months after the date of delivery ]

Low Pressure Chemical Ionization Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector