Tender For supply of fabricated atd bearing removal puller tool fitted on wooden frame of size 2 feet x 2 feet x 2.5 feet with ms angle screw threaded 18 inch. bolt of dia 40 to 50 mm to remove bearing. note: drawing to be got approved by consignee before commencement of work. [ warranty period: 30 months after the date of delivery ]
Tender For supply of 2100001235 drill bit 5mm , 2100001236 drill bit 6mm , 2100001237 drill bit 7mm , 2100000153 grinder straight electric 100mm , 2200011250 hand drilling machine 13 mm , 2100000422 hand blower , 2100000653 allen key set 1by16 inch to 3by8 inch , 2100001540 steel measuring tape 5 mtrs , 2100001486 27 pcs 1by2 square drive 12 point socket , 2100001538 hacksaw frame 12 inch , 2100001605 screw driver size 18 inch , 2100001541 d e spanner 41x46mm , 2100000197 puller tool hydraulic bearing , 2100000411 chain pulley block 2 ton cap , 2100001045 electrician knife , 2100016827 cordless electric drill machine set , 2100000676 adjustable spanners 300mm long , 2100000595 de spanner set 6mm to 32mm , 2100000334 hand crimping tool , 2100000612 grease gun 5 kg bucket type , 2100000618 grease gun 10 kg bucket type , 2100001480 ring spanner set , 2100001176 steel tape 30 mtr length , 2100001090 dbl end spanner open jaw , 2100001047 de spanner 46x50 inch , 2100000941 single end spanner 55 mm , 2100000457 hyd crimping tool 16t
Tender For bid to ras corrigendum : tender for supply of bailey bridge parts d d - extractor pin , jack lifting 15 ton with handle , launching link mk 2 , rocking roller , jack shoe , spanner crancked 3 by 4 inch , podger spanner 3 by 4 inch , rocking roller template , plain roller template , plain roller , panel bb , racker bb , transom bb , sway braces , split pin , panel pin , clamp transom , bolt bracing , bearing bb , ramp plain , ramp button , base plate , post end male , post end female , bolt riband , hd bolts with nut and washer , ew transom clamp , ew bracing frame , chord reinforcement , ew short centre deck unit , ew long centre deck unit , ew transom , ew sway braces , extractor pin , jack lifting 15 ton with handle , launching link mk 2 , rocking roller , jack shoe , spanner crancked 3 by 4 inch , podger spanner 3 by 4 inch , rocking roller template , plain roller template , plain roller , sway braces , balancing beam assy , ratchet spanner , chord reinforcement end tappered male , chord reinfocement end tappered female , spanner 1 by 4 inch podger , chord jack
Tender For corrigendum : supply of double end ctrb mounting machine for mounting the ctrb simultaneously from both ends of wheel set, cap. 70t. as per technical specification given below : (1) hydraulic power pack : double speedmaximum working pressure of 450 kg/cm2 pump, pcm, level gauge, breather, strainer and pressure gauge etc will be installed in the power pack. (2) piston stroke of the cylinder : 450 mm (minimum) (3) capacity of the machine : 70 ton(4) speed (i) advance (idle stroke) 800 mm/min (+/-10%) (ii) installation : 110 mm/min (+/- 10%) (5) type of cylinder :hydraulic double acting (6) jack adjusting height from rail level to centre of installation tube : 360 to 560 mm (7) type of wheel lifting jack : supporting guide jack system with machine frame. ( 8) bearing mounting final pressure : 50+/-tons (will be held for 05 seconds) (9) type of pressure gauge : marking of pressure gauge will be dial in parallel measured in tones and kg/cm2 (10) time of both side mounting of bearing : not more than 2.5 minutes. make : sumanglam. technical specification attached. at annexure a. [ warranty period: 30 months after the date of delivery ]