Lt Ct Meter Tenders

Central Government/Public Sector

Tender For repair/replacement of external electric supply distribution network with other connected items at malad, marve and kandivali under ge (n) santacruz, mumbai - supply, install, testing & commissioning pedestal cubical type double door cted">lt bus bar chamber box of suitable size factory made modular construction fabricated out of 3 mm thick crca sheet, angle iron, channels, epoxy powder coated to give a superior finish , outdoor type , totally enclosed dust & vermin proof with locking arrangements front & back side opening system including rain shed, busbar chamber should be suitable for accomodating all aluminium bus bar strips (50mm x 10mm x 04 nos) & gi strip for earth fixed on porcelain insulators, and one independent metering module suitable for accomodating three phase vocted">lt meters & ammeter digital type, indicator lamps, cable entry/exits cut outs at bottom part, with fixing arrangement on pcc (1:3:6) type c-2 bed block with studs, bocted">lts, nuts & washers, danger notice board with scull suitable for 415 vocted">lts or required size to be fixed on pannel including dismantling of old bus bar panel all as specified and directed by engr-in charge.notes:-(a) aluminium bus bar duly covered with colour coded shrinkable sleeves of required size for phases and neutral - 01 set(b) mccb 4 pole , ics=100%icu- 25 ka, 415 vocted">lts, 100 amps , with thermal adjustable and fixed magnetic setting with extended terminals -02 nos.(c) digital mucted">ltifunction meter of size 96x96 mm to measure current, vocted">ltage, frequency and power factor with buicted">lt in selector switch and programable ct of appropriate ratio.-01 no make- imp/automatic electrical(ae)/ l&t / havells/ meco(d) panel indicating lamp neon/led type (red ,yellow & blue) with lamp holders - 03 nos(e) panel instrumental wiring with frls suitable size but not less than 2.5 sqmm copper wire single core - 01 job(f) necessary sizes of lugs for fixing of cables in bus bar deemded to be included rate quoted by the contractor.make of mccb & mcb: larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 400 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:- larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 160 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 16 ka 100 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb, all as specified and directed by engr-in-charge. make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supply & fixing mccb 4 pole 36 ka 250 amp with adjustable thermal & adjustable magnetic setting, including taking down old unserviceable mccb all as specified and directed by engr-in-charge make:-larsen &toubro/ abb/ siemens/ schneider/ havells/ legrand/ indo asian/ c & s electric/ bhartia cuttler hammer (bch)/benlo, supplying, laying,connecting, testing & commissioning cted">lt ug pvc insulated, heavy duty, 1100 v grade electric cable with aluminium conductor of size 16 sqmm x 4 core, laid in trenches or passing through pipe or fixed to wall, making all connections with and including provision of necessary glands, lugs, bushing etc as required including taking down old unserviceable cable complete all as specified and as directed by engineer-in-charge of following sizes:-note : earthwork excavation, dwc

State Government

Tender For corrigendum : supply of smart energy meters with head end system services in gift city - 1200009630: 1p2w 240v 10-60a cl-1.0 smart meterdesign, engineering, manufacturing, inspection & testing at manufacturers works before dispatch, supply and delivery at destination (at gift store) of ac whole current 1 phase 2 wire, isi marked, 1.0 class accuracy, 10-60 a smart energy meter with dlms protocol & bidirectional communication facility & remote connect/disconnect switch. the meter shall communicate with head end system (hes) on any one of the communication technologies mentioned in is:16444 part 1 compliant with nbiot communication module fall back to 2g, as per the requirement of the utility for measurement of import and export active energy (kwh) with initial and sustained accuracy of class 1.0 for solidly earthed system with balanced and unbalanced loads having power factor in the range of zero to unity (lagging/leading). the meter shall be compatible to common meter reading instruments and other associated instruments & software for remote reading as per requirements given in this specification, 1200009631: 3p4w 240v 10-100a cl1.0 wc smart meterdesign, engineering, manufacturing, inspection & testing at manufacturers works before dispatch, supply and delivery at destination (at gift store) of ac whole current 3 phase 4 wire, isi marked, 1.0 class accuracy, 10-100 a smart energy meter with dlms protocol & bidirectional communication facility & remote connect/disconnect switch. the meter shall communicate with head end system (hes) on any one of the communication technologies mentioned in is:16444 part 1 compliant with nbiot communication module fall back to 2g, as per the requirement of the utility for measurement of import and export active energy (kwh) with initial and sustained accuracy of class 1.0 for solidly earthed system with balanced and unbalanced loads having power factor in the range of zero to unity (lagging/leading). the meter shall be compatible to common meter reading instruments and other associated instruments & software for remote reading as per requirements given in this specification, 1200009632: 3p4w 240v -/5a cl0.5s ct smart meterdesign, engineering, manufacturing, inspection & testing at manufacturers works before dispatch, supply and delivery at destination (at gift store) of 3 phase 4 wire, isi marked, 0.5s class accuracy, fully static cted">lt current transformer (ct) operated smart energy meter with dlms protocol & bidirectional communication facility. the meter shall communicate with head end system (hes) on any one of the communication technologies mentioned in is:16444 part 2 compliant with nbiot communication module fall back to 2g, as per the requirement of the utility for measurement of import and export active energy (kwh) with initial and sustained accuracy of class 0.5s for solidly earthed system with balanced and unbalanced loads having power factor in the range of zero to unity (lagging/leading). the meter shall be compatible to common meter reading instruments and other associated instruments & software for remote reading as per requirements given in this specification, 1200009630: 1p2w 240v 10-60a cl-1.0 smart meterdesign, engineering, manufacturing, inspection & testing at manufacturers works before dispatch, supply and delivery at destination (at gift store) of ac whole current 1 phase 2 wire, isi marked, 1.0 class accuracy, 10-60 a smart energy meter with dlms protocol & bidirectional communication facility & remote connect/disconnect switch. the meter shall communicate with head end system (hes) on any one of the communication technologies mentioned in is:16444 part 1 compliant with nbiot communication module fall back to 2g, as per the requirement of the utility for measurement of import and export active energy (kwh) with initial and sustained accuracy of class 1.0 for solidly earthed system with balanced and unbalanced loads havin

Tender For corrigendum : items - computer and servises and otheres, mcb (miniature circuit breaker), acb (3200a/4000a ), acb (air circuit breaker), allen key set, amf relay, ammeter, annunciation system, anti-corrosion spray, arc flash suit, arc flash suit (ht/cted">lt panel ), auxiliary contacts, avr (automatic vocted">ltage regulator), battery charger, blower/air blower, breather assembly, bus coupler acb, busbar insulators, busbar supports, cable glands, cable glands, cable lugs, cable ties, cable ties, changeover switch, clamp meter, clamp meter, combination pliers, consumables, contact cleaner spray, contactor, continuity tester, control cable, control fuses, control relay, control wires, cooling fan, copper busbar, crimping tool, ct (current transformer), current transformer (ct), dg set synchronization panel (3 750 kva), digital mucted">ltimeter, digital mucted">ltimeter, discharge rod, earth faucted">lt relay, earth switch, earth tester, earthing rod, electrical contact cleaner, electrical gloves (11 kv rating), electrical safety gloves, emergency stop switch, energy meter, engine control module, face shield, ferrules, ferrules, flexible wire, frequency meter, fuse fuse base, heat shrink sleeves, heat shrink tubes, hrc fuse, hrc fuses, ht protection relay, indicator lamps (r/y/b), infrared thermometer / thermal camera, insulated screwdriver, insulation tape, isolator switch, lightning arrester, load sharing module, lockout-tagout (loto) kit, loto kit, cted">lt pcc/mdb panel, lubricant spray ( ), lugs, maintenance tools, mccb, mccb (molded case circuit breaker), megger (insulation tester), megger 5 kv, microfiber cloth, motorized mechanism, mucted">ltifunction meter, mucted">ltifunction meter, nose pliers, numerical protection relay, oti (oil temperature indicator), over current relay, overload relay (olr), phase sequence meter, phase sequence tester, plc module, power analyzer, power cable, power factor meter, protection & metering, pt/vt (potential transformer), push buttons (start/stop), pvc insulation tape, reverse power relay, rust remover, safety equipment, safety goggles, safety helmet, safety helmet, safety shoes, safety shoes, screwdriver set, secondary injection test kit, selector switch, shunt trip coil, side cutter, silica gel, smps (power supply), soft brush, spanner set, speed governor module, spiral wrapping, spring charging motor, starting relay, synchronizing relay, terminal blocks, thermal camera, thermostat, timer relay, torque wrench, transformer buchholz relay, transformer oil, under/over frequency relay, under/over vocted">ltage relay, uv coil, vacuum cleaner, vcb (vacuum circuit breaker), vocted">ltage tester, vocted">ltmeter, wire markers, wire stripper, wti (winding temperature indicator), , , , comprehensive maintenance of substation, transformer, panels, synchronization panel a including all consumables, accessories, minor & majour spares, cleaning materials, testing instruments, preventive maintenance and breakdown maintenance complete., annual maintenance of substation, transformer, panels, synchronization panel a including all consumables, accessories, minor spares, cleaning materials, testing instruments, preventive maintenance and breakdown maintenance complete.

Tender For supply of pn or zener diode or led characteristics apparatus , verification of kcl and kvl , resistance in series and parallel apparatus , ohms law apparatus without power supply , ohms law apparatus with aluminum panel 2 digital panel meters and power supply , transistor characteristics apparatus , fet characteristics apparatus , half wave full wave and bridge rectifier apparatus , ripple factor apparatus , digital logic trainer , verification of truth table of logic gates using universal gates , flip flops using nand gates and ttl ics , four bit counters synchronous and asynchronous , four bit shift registers , encoder or mucted">ltiplexer eight to one line , decoder or demucted">ltiplexer one to eight line , four bit analog to digital convertor , four bit digital to analog convertor , light intensity or phase control using scr or triac , scr commutation techniques , switching action of a bjt , single phase half wave full wave and fully controlled bridge rectifier or convertor using scrs , three phase half controlled bridge converter with r and rl load , three phase fully controlled bridge converter with r and rl load , single phase cycloconverter , instrumentation trainer using transducers , burdon tube pressure gauge trainer kit , strain gauge trainer kit with cantilever beam , lvdt trainer kit , speed measurement using photo electric and magnetic sensors , temperature sensors kit , measurement of water level using strain gauge , measurement of water level using capacitance transducer , ac servo speed torque characteristic trainer , dc servo motor speed torque characteristics trainer , stepper motor controller trainer , analog lab trainer bread board model , digital lab trainer bread board model , plc trainer , transmission line trainer abcd t and pi parameters ferranti effect load test , idmt over current relay testing kit electromechanical type , buchholz relay testing kit with compressor and oil , over vocted">ltage relay testing kit electromechanical type , over current and earth faucted">lt relay testing kit three phase static type , over current relay testing kit static type , measurement of power and power factor single phase and three phase , to study a typical bhk house wiring , four to one mucted">ltiplexer and one to four demucted">ltiplexer , vapour compression refrigeration vcr test rig , water cooler setup , air conditioning test rig , domestic refrigerator , window air conditioner , split air conditioner , air cooler evaporative , tube cutter , pipe bender , flaring and swaging tool kit , reamer , brazing torch , manifold gauge set , vacuum pump , refrigerant recovery unit , refrigerant charging cylinder or electronic charging scale , refrigerant leak detector , digital clamp meter , digital thermometer , anemometer , tachometer , insulation material , refrigerants , recovery cylinders , weighing machine , electrical control panel , work benches , safety equipment

Central Government / Public Sector

Tender For corrigendum : supply of power factor meter - digital (q3)

Tender For corrigendum : supply of fuse link 2 amp hrc , fuse link 10a , fuse link 6a , fuse link 4 amp hrc , frequency meter 45-50-55 hz red mark at 50hz , vocted">ltmeter 0-500v red mark at 415v , power factor meter 0.5-1-0.5 red mark at 0.8 , fuse link 63a , fuse link 25a , fuse link 100a

Tender For purchase of non consumable items for physics laboratory department of basic engineerin - purchase of physics laboratory equipment for basic engineering department, "digital balance weight 500g, accuracy 0.01g, top pan. tare function, caliberation- automatic external display type: led ", "joule’s calorimetercopper vessel, battery eliminator3a, (2,4,6,8,10,12 v), tubular rheostat 20-3.3a, one way plug key, analog type dc ammeter (02a), vocted">ltmeter (0-5v), thermometer (alcohol), stop clock ", "ic regulated battery eliminator ic regulated, input: 230v ac; output: 0-12v dc in steps of 2v; capacity: 1a or 2a. ", "galvanometer moving coil type, 30-0-30 scale, unbranded with bhel specification-sensitivity 0.143mm/v ", "vocted">ltmeter dc vocted">ltmeter; range 0–10 v, analog ", "ammeter dc (0 - 2 amp) ", "parallelogram apparatus parallelogram law of forces apparatus fitted with stand ", "decade resistance box resistance box 12 month warranty (dial type) -manganin coil- 2 dials ", sonometer apparatus sonometer with meter scale attached along with knife edge, tuning forks set 256, 384, 512 ranges, hammer, slotted weight - 500 gm each to a total of 3 kg. brass wire (5 m) , travelling microscope branded travelling microscope 0200 mm horizontal and 0-150 mm vertical measurement, potentiometer it features a 1-meter to 10-meter constantan/manganin wire stretched on a wooden or sunmica baseboard with a millimeter scale. it includes 4mm brass terminals, a pencil jockey for contact, wire options (10 wires), and a typical resistance range of 10-20 ohms, ideal for high-precision vocted">ltage measurements, viscosity apparatus • stoke's apparatus with metre scale attached and long cylindrical glass jar, glass beads small size (1 box), screw gauge (0-15 mm, "rheostat high-grade ceramic tube, oxidized resistance wire, 0.5a5a, range 10ω–100ω. ", deflection magnetometer apparatus • to deflection magnetometer apparatus with compass box and two short bar magnets, "solar cell kit the apparatus consist of variable dc power supply, led, solar cell and two mucted">ltimeters (or an ammeter and a vocted">ltmeter). a variable dc power supply of 05v. light source is provided by led. the illumination intensity of the led can be controlled ", wheatstone bridge kit ujt series arm: four decade dials in steps of thousands, hundreds, tens, & units of ohm's. ratio arm: the ratio arm of the bridge is capable of selecting mucted">ltiplying factor of 0.001, 0.01, 0.1, 1, 10, 100, 1000 for resistance measurements. two press keys are provided, one marked b is for battery & one marked g is for galvanometer one toggle switch is provided for internal battery a sensitive galvanometer is provided in the bridge, ohm's law verification kit battery eliminator-3a, (2,4,6,8,10,12 v), tubular rheostat 20-3.3a, one way plug key, analog type dc ammeter (0-2a), vocted">ltmeter (0-5v), standard resistance coil of 1, 2 ohm (2-set) wound on a wooden bobbin, "torsional pendulum torsional pendulum metallic disc, symmetrical masses and pendulum stand, steel wire ", compound bar pendulum one meter long iron strip well painted with holes at a distance of every 5 cm and also with pair of brackets and a heavy base table top stand with stop clock, "meter bridge type: 1 m length, with uniform wire (resistance wire) material: constantan or manganin (low temperature coefficient) scale: 0–100 cm, engraved or printed base: wooden or metal, rigid, non-conductive support joints / terminals: brass or copper, fixed for connections 2. galvanometer type: analog, moving coil or digital (for null detection) range: sensitive to detect microampere currents internal resistance: high, typically ~100 ω or as specified 5. cells / power supply type: leclanché cells (1.5 v each) or dc power supply number: 2–4 cells in series (or supply ~3–6 v) "

Tender For supply of power factor meter - digital (q3)

corporations/Associations/Others

Tender For auction sale of single phase meter static/ pushfit type burnt without box (e-waste),poly phase meter static/ pushfit type burnt (e-waste),poly phase meter static/ pushfit type burnt without box (e-waste),cted">lt shunt capacitor a/s,cted">lt ct assorted ratio scrap,cted">lt ct meter scrap poly phase (a/s) (e-waste),33 kv ctpt set scrap (assorted ratio),11 kv ctpt set scrap (assorted ratio),11 kv ct scrap,11 kv pt scrap (a/s),rubber tube scrap assorted size,rubber flap scrap assorted size,vehicle battery 12 v u/s scrap (pcb applicable),scrap laptop (e-waste),mccb assorted ratio scrap three phase,printer scrap (e-waste),empty drum c/d class,scrap empty drum of cable/iron(reel),scrap unservicable rotating sub standard active,scrap phantom load

State Government

Tender For - r/ mtc. of rws/jjm schemes/ s.h.: providing & fitting fixing of electrical accessories, spare of panel board of different water supply schemes at different locations under hrishyamukh rd block under dws sub-division, belonia during the year 2026-27. - providing and fitting fixing of spare contact kits without coil (l & t make) for auto star dected">lta starter., b) ml-2 type., c) ml-1.5 type., providing and fitting fixing of standard operating coil (l & t make) for auto star dected">lta starter., b) ml-2 type., c) ml-1.5 type., supplying and fitting fixing of 4 pole ac control contactor (nhd series) suitable for bch made starter (standard coil vocted">ltages are 24, 110, 220/240 & 380/415 v, ac hz)., supplying and fitting fixing of 3 pole power contractor (type-mnx) suitable for 10 hp to 25 hp motor.mnx-25 (for l&t made starter), supplying and fitting fixing of pneumatic timer pn type delay relay-electro pneumatic) suitable for delay of time upto 30 sec. (bch made)., supplying and fitting fixing electronic timer type st-100 (l & t make) suitable for 240/300/415v, 50 hz having ranges for 3-30 secs/12-120 secs., supplying and fitting fixing of single phase preventer on delay 2 sec off delay 7 sec 65 vac asymmetry., providing & supplying of kit-kat rewireable porcelain fuse (cut-out) carrier & base of havells made (delux quality)., a) 63 amps/415 vocted">lt, b) 100 amps/415 vocted">lt, supplying and fitting fixing of 3 pole power contractor (type-ml) suitable for 10 hp to 25 hp motor.type ml-2 (for l&t make starter), supplying and fitting fixing of thermal timer type gt-200 (l & t make) suitable for 230/250v, 360v, 400/440v, 50 hz for 5-18 secs., supplying and fitting fixing of thermal overload relays mn2 type (directly operated& direct mounting on mnx 9-40 contactor) of l & t made. (suitable for ml/mnx type)., a) for relay range 9-15 a., b) for relay range 14-23 a., c) for relay range 20-33 a., supplying and fitting fixing of thermal overload relays (directly operated& direct mounting on ml-2/3 contactor) having relay range 9-14a/13-21a of l & t made. (suitable for ml-2/ml-3 type)., supplying and fitting fixing of citation-m overload relays (direct mounting with buicted">lt in single phase protection) having relay range of bch made., a) for relay range 8.9-13.5 a., b) for relay range 13.2-30.00 a/17.4-24.00 a., c) for relay range 22.00-30.00 a., providing and fitting fixing of 6 feet x 4 feet x 1 inch (thickness) gamair wood/ plywood pannel board for fitting fixing of electrical items, in/c 2 nos ms angle post ( size 2 inch x 2 inch x 9 feet ), nuts & bocted">lts etc. for irrection of the same by 1:1.5:3 cement concrete casting ( 1 feet x 1 feet x 2 feet) below the ground level and painting two or more coats & plastic paint as per specification and direction of the engineer-in-charge., providing and fitting fixing 3 phase indicating lamp fiited with panel board with three different colour lamps with batten holder complete as per specification and direction of the engineer-in-charge., providing and fitting fixing heavy duty box type (resin filled) power factor correction capacitor l & t make etc. complete as per specification and direction of the engineer-in-charge.i) 5-15 kvar 440 v, supplying isi marked/ taparia make tools for water supply scheme., i) sly wrench, ii) screw driver, iii. pipe wrench, iv. plier, v. hexo frame with blade, providing and fitting fixing of moving iron type, range 0-500 v, 96 mm x 96 mm size ac vocted">lt meter ( l & t / ae make) with selector switch as a electrical instrument of the pannel board as per specification and direction of the engineer-in-charge., providing and fitting fixing of moving iron type, range 0-100/0-200 amp, 96 mm x 96 mm size ac amps meter direct reading type ( l & t / ae make) with selector switch and ct coil as a electrical instrument of the pannel board as per specification and direction of the engineerin-charge., providing and fitting fixing stee