Tender For supply and installation of electrical and mechanical equipment of tubewell at road no.66 jafrabafad and shastri park tubewell. (re-invite) - supply and installation of electrical and mechanical equipment of tubewell at road no.66 jafrabafad & shastri park tubewell by carrying out following works:- dismantling/lifting of tubewells with the help of gas cutter and heavy manual labour., supply of pvc insulated sheathed copper conductor cable for submersible pump motor of size 6mmsqx3core make :- finolex/ havells/ grandlay/djb approved make, supply of 80 mm dia d/f g.i pipe in b class as per isi 3 mtr long complete with cutting flange for submersible cable and support welded. make :- jindal/ tata., supply of tail piece medium class 0.5 mtr long including one end flanged and other end threaded of 80 mm dia., supply of 80 mm dia g.i bend with both side flanged welded, s/o m.s. clamp of m.s. strip 8mm thick duly hole for holding the pipe of 80 mm dia with nut bolt and washer, s/o m.s bore cover made out of m.s. plate suitable for 12" dia bore complete with suitable hole for pssing the 80mm dia gi pipe., s/o ci, d/f swing type nrv of 80mm dia make:- kirloskar/ ivc/djb approved make., s/o electronic dozing pump (4lph,5.5 kg) electrically controlled operated 230v, 50 hz, supply chemical grade tank of 100 ltrs with pipe make- milton roy/clomax, s/o nut bolts with washer of good quality of 1/2"x2" size, s/o rubber packing sheet synthetic 50% make :- jyoti / national, lighting arrangement including providing fixing1 no. tube light fitting 40 watt, 1 no. bulb point, 1 no. flood light on wall of room and also control board.etc.i/c electrification of room., labour charges for lowering the submersible pump set with all allied e&m equipments and fixing delivery line, valves, electronic dozing pump i/c hardware items as nut, bolts & washer i/c cartage to & fro., lt panel work of tubewell in road no.66 jafrabafad & shastri park tubewell:- dismantling of lt panel with allied equipment with the help of skilled labour., s/o power contactor 32 a. triple pole. make l &t/ havells, s/o front mounting add on aux contact block. make : havells/l&t, s/o three pole power contractor -25a cap. make l&t/ havells, s/o ampare meter (0-30a) 4 size squ. type. make l&t/ae, s/o voltmeter (0-500v) 4 size squ. type. make ae/l&t, s/o indicating lamp set for ryb phase. make l &t/ havells, s/o single phase preventor. make l&t/ minilac, s/o timer switch digital/anolog type. make l&t / havells, s/o over load relay thermal type 14-23 a. make l &t/ havells, s/o star delta timer on delay. make l&t /havells, s/o sp mcb 6a. make : l&t/havells, s/o 3p mcb 63. make : l&t/havells, push button 22.5mm(red / green), s/o 4p 63 amp elcb make : l&t/havells, changeover switch 63 amp., s/o 100a 3p mccb 25ka. with spreader make : havells/l&t., s/o rubber mat for electrical purpose of size 1mx2m and 3mm thick. make:- jyoti/ national, labour charges for repairing of lt panel with installation of above components i/c electric connection , testing and commissioning on load.
Tender For corrigendum : supply of supply installation and commissioning of machine and equipment of dft d d double needle chain stitch machine with motor table snd stand complete set , electronic button holer motor table and stand complete set , blind stitch machine motor table and stand complete set , twin needle feed off the arm machine along with puller lap seam folder complete set , multi needle chain stitch machine with front placket folder machine motor table and stand complete set with folder , 4 threads cylinder bed over lock stitch machine motor table and stand complete set , 5 threads flat lock stitch machine with cylinder bed , anthropometric ergonomic kit , lock stitch button sewing machine complete set with control panel , 5 threads flat lock stitch machine
Tender For electronic spares for techmeta 8kw electron beaqm welding 213a machine - electronic spares for techmeta 8kw electron welding 213a machine (as per enclosed scope of work, specifications, list of deliverables and atp enclosed), wide range gauge mpg500-inficon, recgcan board for 213, apw card-grid control, power supply card, foc 4c board: control of focus current if/ibk card, focus bisplay board, diflection card, if/ibk card, power supply card liner reg+/- 10 to 15v with clibration support, video nc control panel ref:exa-s, gun light control, focus coil
Tender For supply of automatic star delta starter panel in 16 swg steel sheet enclosure of size 600x750x200 mm,three phase 415 v, ac, load current 70 amp, 50 c/s, 40 hp, light gray spray painted, panel wiring of powersection with 1x35 sq mm multi stranded pvc insulated copper conductor 1.1 kv grade, comprising of - 01 no hlvd2 voltage sensing relay, 01 no, qt-100 time switch, 01 no hour meter, 01 set phase sequence indicator, 6-way connector, 01 no toggle switch 15 amps, 01 no ammeter (0-200a), 01 no voltmeter (0-600v),01 set ct coil 100/5 & 15va, 03 nos led indication lamps, 01 no selector switch (ass), 01 no selector switch (vss), 03 nos cut out 6a for control, 03 nos toggle switch 6a for control, 2 set green/red push button for on/off, 01 no kwh meter type ct 2m - 200/5 ct operated, 03 nos ml- 4 contractor with 2no & 2nc, 1 no bi-metallic over load relay (40-70a) type mn x r4, 01 no electronic timer (0-30 sec), 01 no motor protection relay, 01 no mccb type dh- 200/35ka, 01 no time delay relay (0-30 minute). make- l&t, c&s and abb or similar [ warranty period: 30 months after the date of delivery ]
Tender For a) scope of work covers supply, installation and commissioning of total 12 nos.of 3d radar level transmitters for the coal level measurement in raw coal bunkers of rtps-unit-5&6 with required pcs, electronic modules, splitters, modems, junction boxes, mounting kit, enclosures, interconnecting cables, software and all other accessories required to make the system complete and fully functional, shall be provided for continuous level measurement and monitoring of level of each coal bunker and also to ensure satisfactory performance of the system commissioned at rtps site which shall be on the basis of single point responsibility, completely covering the activities and services in respect of all the equipment works specified and covered under the specifications. the work involves i) installation and commissioning of 12 nos. 3d radar level type level transmitters with suitable mounting accessories, display indicators, isolators, annunciator, smps, terminals, panel internal wiring, led bulbs, door switch etc. at the bunker level ii)commissioning of rs 485 communication /other cables from bunker level transmitters to the desktop pc at u-5&6 control rooms.iii)commissioning of desktop pcs for 3d multi vision for monitoring of all the 12 bunkers level at u-5&6 control room respectively and also both units bunker levels at pc being installed at chp control room. iv)loading of all the required licenced software to the desktop pc for 3d radar level transmitter and cable routing, glanding, mounting of cable tray, termination and ferruling is in the contractors scope.cable trays will be provided by m/s.kpcl.b)all fabrication works required for installation and commissioning of instruments with jbs,protective cover/canopies and allied works are in contractor/agency scope itself.c) all civil works like drilling/cutting rcc floors,grouting,refilling floors,conduiting under ground cables cable tray mounting, masonary works are in contractor/agency scope itself.d)storage of materials while executing works is single point responsibility of contractor/agency scope itself. e)software details-1. the page containing all bunker level data shall be in full page which must be visible from at least a distance of 6-8mtr .(font size should be more) and shall have a historical trend storage for minimum 45days & real time trend with not less than15min sampling time. f) at chp control room, the existing kpcl pc shall be enabled with bunker level software & shall be communicated through existing lan and as a redundancy the seperate optical fiber cable communication with media convertor has to be provided.the lan cables has to be protected with cable conduit g)materials supply shall be completed in all respect within the stipulated period as per the contract. materials shall be delivered to rtps site through ee(stores)o&m. unloading of materials at rtps site location and shifting of the same to work location is under the contractor/agency scope only. h)handling, shifting, unpacking and erection and commissioning of the entire system shall be under the scope of bidder itself. i)all required consumables, hardware and licenced software, accessories and any other materials which are not included in the scope and required for successful installation and commissioning of the 3d radar level transmitters for the coal level measurement in raw coal bunkers of rtps-unit-5&6 are under the contractor/agency itself. j)all the materials required for the installation and commissioning of 3d radar level transmitters for the coal level measurement in raw coal bunkers of rtps-unit- 5&6 shall be made as detailed under the technical specifications. k)interfacing of all the bunker level transmitters outputs to the desktop pcs at u-5&6 control rooms through rs - 485 communication protocol.(the required 1 pair x 1 sq.mm shielded armoured cables as per requirements shall be supplied approx-500 meters or if more). for more details of scope of work refe