Tender For supply of condenser blade , 4 mfd capacitor , samsung timer , white wrapping tape , teflon tapes , cello tape 2 black , cotton waste , danfoss relay set 20 deep freezer , 80 by 100 mfd capacitor , minus 20 deep freezer square type , pin remover charging , thermostat minus20 , relay danfoss , capacitor 4 mfd , condenser fan blade for 2 ton llyod ac , pinch pliers , t handle 10inch , t handle 12inch , sand paper , 1 by 4inch ratchet , refrigerant recovery plier , allen key set in inches , cold room evaporator fans , 8 mfd capacitor , nose pliers , wire cutter , charging line r32 , two way manifold gauge with box and hose , 46 pcs set , cylinder key , tourch for butane gas cylinder , swaging tools , rough file with handle , double end spanner set 6x32 mm , t set 13inch , t set 14inch , drain line spring , single gauge high side , measuring tape 5 meters , expansion valve for cold room , condenser motor , capacitor 3 mfd , digital temp meter , samsung heater , timer , condenser fan blade , valve 3by8inch hand shut off , cylinder valves , condenser motor , fan blade , hand cutter blade iron , adjustable wrench 6inch , adjustable wrench 8inch , adjustable wrench 12inch , allenkey set mm , flaring tools set with box , smooth file with handle , r22 charging line , t handle only 1by4inch , multitec screw driver , t handle 8inch , t handle 11inch , t handle 13inch , tube cutter , flare nut 3by4inch , square type condenser fan motor , tong tester with probes and leather cover , screw driver long , hammer with wooden handle , cutting plier , tube cutter small , hexa frame with blade , evaporator fan motor for lg refrigerator , condenser copper coil make llyod , filter , single pressure gauge high side500psi , gauge value , danfos 20 relay olp set , try square set , valve core removal tool , digital vernier callipers with batteries , siron soldering iron set , soldering wire , ) /bid number : gem/2025/b/6597172 * /dated: 22-08-2025 & & / bid document 1 / 87 & & ' ' /item category compressor cable kit , handset valve 1by4inch , cuppler , 24 socket wrench set ratchet , pin valve , charging line handle , capacitor 50 mfd , 3 way 30 amps connector , ss tank nipple 1by2inch , pvc connection pipe 1 by 2 inch , ro water purifier t type tap , ro water purifier tap tank kent type , charging line rubber , pipe wrench 16inch , bearings , oil seal , ss breazing roads , bluestar indoor blower for 1point5 ton sac , line tester , screwdriver small , screwdriver large , handle t , jet pump handle small , araldite 500gms , double ended ring spanner set , single guage low pressure for vaccume , t type handle spanner set , continuity tester compressor check , servicing covers , compressor for 345 liters refrigerator , electrical relay , compressor for minus20 deep freezer 320 liters , compressor for 165 liters bpl make refrigerator , compressor for minus20 deep freezer 350 liters , filter drier pencil type , compressor for -20 deep freezer 500 liters , compressor for 1point5 tr split ac rotary type , side dummy nuts 5by8inch , side dummy nuts 1by2inch , side dummy nuts 1by4inch , side dummy nuts 3by8inch , dummy nuts 1by4inch , ductable split ac indoor blower , rubber bushes , minus20 deep freezer compressor , drier cum filter , refrigerant r 600a , hand shut valve for r600a portable cylinder , water pipe pvc , acetylene cylinder regulator , oxygen cylinder regulator , hose pipe for acetylene , hose pipe for oxygen , torch for oxygen acetylene cylinder , clamps for hose pipes , hand hacksaw bladed , axial fan motor for hitachi 16point5 ton ac , compressor for ice machine 120 kg per hr production , filter cum drier , compressor for bluestar split ac 1point5 ton , capacitor 45 mfd , capillary tube gauge , soldering liquid flux , blower for lloyd make split ac 1point5 ton , pvc pipe 3by4inch , pvc bends 3by4inch , pvc pipe 1inch , pvc bend 1inch , clamps 3by4inch , clamps 1inch , pvc t joint 3by4inch , pvc solvent , cutting machine blade , vc t
Tender For supply of printing of register e e - movement out register , internal mail out register , numerical index and document record card , duty warrant odd even officer register , duty odd even officer register , drss register , immols register , di register , book in out register , work order register , bio chemestry register , bin cards , ledger sheets card , medical case sheet , request for special investigation form with blood investigation form , request for special investigation , sick report performa , annual medical investigation form , odd even daily tool issue return record register , tester calibration record register , monthly check certificate register , demand rv lpp register , continuity traing record register , individual continuity traing record register , ojt record register , crash trolly register , daily task record register , task detailing record , battery ct record , fol stock record register , hydraulic sampling record register , expense book register , fuel sampling record register , ground equipment servicing register , wheel hub register , earth pit register , file cover , car diary , kilometer card ) /bid number : gem/2025/b/6593398 * /dated: 21-08-2025 & & / bid document 1 / 29
Tender For supply of electrician items : - led tv trainer kit , mobile phone trainer , battery charger , autotransformer , iot trainer kit , continuity tester , de soldering gun , cut out relays , reverse current , over current , under voltage , ohmmeterseriestypeshunttypeportableboxtype , megger , linear ic trainer , current transformer , solar panel with battery , parallel operation of transformers , parallel operation of alternators , load bank variable , bar magnet , mixture and grinder , motor pump set , package ac , walk in cooler puf insulated , vrfvrv unit with two indoor units 25tr each and 5tr capacity , absorption system , airconditioning direct system trainer , visi cooler trainer , bottle cooler visible , bus ac tutorial model trainer , air conditioning indirect system water cooled , service oscillator
Tender For tender for supply of ndt and inspection of msv at lalru lpg plant : : - disconnection and safe handling of lpg bullet fittings and accessories for 1445 mt mounded storage vessel , degassing , sludge disposal , and reinstallation activities for 1445 mt mounded storage vessel , provision of internal scaffolding and safety arrangements for inspection of 1445 mt mounded storage vessel , provision of flameproof lighting and ventilation for inspection of 1445 mt mounded storage vessel , internal surface cleaning and weld joint preparation for 1445 mt mounded storage vessel , external inspection of mound , structural supports , and nozzles for 1445 mt mounded storage vessel , reconnection of lines , valves , and fittings with purging , ultrasonic thickness measurement of shell , dished ends , pipelines , and nozzles for 1445 mt mounded storage vessel , wet fluorescent magneticparticletesting of welds and nozzles for 1445 mt mounded storage vessel , 100% ultrasonic flaw detection of welds for 1445 mt mounded storage vessel , dye penetrant testing of accessible areas for 1445 mt mounded storage vessel , hardness testing on welds , haz , and parent metal for 1445 mt mounded storage vessel , radiographic testing of weld joints at selected locations for 1445 mt mounded storage vessel , dry/wet type calibration and chart preparation for 1445 mt mounded storage vessel , settlement checking of mounded bullets using laser and theodolite techniques for 1445 mt mounded storage vessel , replacement of gaskets , studs , nuts , and bolts for fittings on 1445 mt mounded storage vessel , submission of testing and inspection certificates as per smpv rule 19 for 1445 mt mounded storage vessel
Tender For corrigendum : supply of goods, tools & equipmentforan international standard itotin welder tradeat iti rajkot, gujarat, indiapackage 2: welder trade - electrode holder, h.p. welding torch with 5 nozzles, welding transformer with all accessories (400a, ocv 60-100 v, 60 percent duty cycle), welding transformer with all accessories (300a, ocv 60 - 100 v, 60 percent duty cycle), inverter-based welding power source, d.c arc welding rectifiers set with all accessories, gmaw welding machine, ac/dc gtaw welding machine, spot welding machine to15 kva with all accessories, gas welding table with firebricks, arc welding table with positioner, oven, electrode drying, table for gas cutting, welding simulator for smaw / gtaw / gmaw, seam welding machine(longitudinal) 75 kva with accessories, submerged arc welding machine with accessories (1000amps), friction welding machine, welding motor generator, fume extractor system connecting all the welding booths, mag welding robot with all standard accessories, welding booth with forced fume extractor, for welding machines, carriage welding system, 400 amps with industry 4.0 ready multi process welding set, gas manifold system, magneticparticletesting machine probe type with all standard accessories, oxygen gas pressure regulator double stage, acetylene gas pressure regulator double stage, co2 gas pressure regulator, with flowmeter, argon gas pressure regulator with flowmeter, flash back arrester (torch mounted), flash back arrester (cylinder mounted), air plasma cutting equipment with all accessories, air compressor suitable for air plasma cutting system, portable gas cutting machine capable of cutting straight & circular with all accessories, pedestal grinder fitted with coarse and medium grain size grinding wheels, bench grinder fitted with fine grain size silicon carbide green grinding wheel, ag4 grinder, hand shearing machine capacity to cut 6mm sheets and flats, power saw machine, work bench, oxygen, acetylene cylinders, co2 cylinder, argon gas cylinder, anvil 12 sq. inches working area withstand, swage block, portable abrasive cut-off machine, potable cnc profile cutting system with all standard accessories, ultrasonic flaw detector with accessories, eddy current tester
Tender For corrigendum : supply of goods, tools & equipmentforan international standard itotin welder tradeat iti bhilad, gujarat, indiapackage 2: welder trade - electrode holder, h.p. welding torch with 5 nozzles, welding transformer with all accessories (400a, ocv 60-100 v, 60 percent duty cycle), welding transformer with all accessories (300a, ocv 60 - 100 v, 60 percent duty cycle), inverter-based welding power source, d.c arc welding rectifiers set with all accessories, gmaw welding machine, ac/dc gtaw welding machine, spot welding machine to15 kva with all accessories, gas welding table with firebricks, arc welding table with positioner, oven, electrode drying, table for gas cutting, welding simulator for smaw / gtaw / gmaw, seam welding machine(longitudinal) 75 kva with accessories, submerged arc welding machine with accessories (1000amps), friction welding machine, welding motor generator, fume extractor system connecting all the welding booths, mag welding robot with all standard accessories, welding booth with forced fume extractor, for welding machines, carriage welding system, 400 amps with industry 4.0 ready multi process welding set, gas manifold system, magneticparticletesting machine probe type with all standard accessories, oxygen gas pressure regulator double stage, acetylene gas pressure regulator double stage, co2 gas pressure regulator, with flowmeter, argon gas pressure regulator with flowmeter, flash back arrester (torch mounted), flash back arrester (cylinder mounted), air plasma cutting equipment with all accessories, air compressor suitable for air plasma cutting system, portable gas cutting machine capable of cutting straight & circular with all accessories, pedestal grinder fitted with coarse and medium grain size grinding wheels, bench grinder fitted with fine grain size silicon carbide green grinding wheel, ag4 grinder, hand shearing machine capacity to cut 6mm sheets and flats, power saw machine, work bench, oxygen, acetylene cylinders, co2 cylinder, argon gas cylinder, anvil 12 sq. inches working area withstand, swage block, portable abrasive cut-off machine, potable cnc profile cutting system with all standard accessories, ultrasonic flaw detector with accessories, eddy current tester
Tender For supply of 1 kv industrial insulation tester for condition monitoring and trms & dc voltage measurement insulation testing up to 1000 v and 100 g ohms continuity testing up to 200 m a or 20 m a down to 0.01 ohms pass/fail limit alarams, combined analog and dual digital display, pi/dar and timer function, 50 v, 100 v, 250 v, 500 v, and 1000v +pi. dar. including accessories. red/black silicon test leads with probes and clips user guide cd, batteries 6x aa alkaline 1.5 v, carry case. make: fluke, flit, metravi, extech or similar.
Tender For supply of magnetic ink (red in color) in paste form, oil based, use 10 gm/liter in 01 kg pack for magneticparticletesting. it shall be able to detect cracks through mpi technique.astm-e-709 & is 6410 make: ferrochem or similar