Tender For bridge unloader - bridge unloader, 1. design, manufacturing and supply of heavy duty out door bridge for sugar mill plant cane unloading conforming to is:807-1976 & is:3177- 1977 fabricated from m.s. plate section conforming to is:226/2062 steel in box type design with and carriage fitted with wheel of fusion welded having l type bearing housing for long travel (lt) wheel assemblies having span-22.00 mtrs capacity -05ton swl along with dismantling of old existing bridge and erection and commissioning of new bridge old existing cross travel trolley will be used. type of bridge-m.s. plate fabricated box type span-22.00 mtrs, unloading capacity -05 ton swl2. techincal specification:-type of bridge -box type (m.s. plated fabricated), capacity-05 ton swl, unloading capacity -80 to 100 ton cane/hr, utility-sugar cane handling, height of top of top rail from ground-10.00 mtrs, height of lift-12.50 mtrs, wirerope19mm, 6/36 construction fibre wire, long travel speed -23-25 meter/minute, box side plate height-1250mm, box side plate thickness8mm, top & bottom plate thickness-top plate-12mm thick, bottom plate-10mm thick, top & bottom plate width-500mm, baff /stiffener plate spacing -750mm, baffle/stiffener plate thickness-8 mm., 3. end carriage:- length-5000mm, height-450mm, centre distance for end carriage wheel-4500mm,centre distance of trolley wheel as per previous trolly.4. long travel mechanism:- size of rail top at long travel- width-60mm, height-25mm, size of rail section at cross travel-width-60mm, hight25mm.5. electric motors for long travel drive 5.3hpx960 rpm rating s4 duty, qty-02 nos.6. gear box for long travel:- type helical,model-hb-350, ratio-40:1, service factor-greater than 2 on installed power, qty-02 no7. coupling for long travel drive:- type geared type half gear model1038. breaks:- thruster-electro hydraulic thruster 18 kg/cm , dia-6", qty 02 no., floating shaft dia/length-70mm/800mm-1000mm9. wheel:- dia meter-420mm, bearing-22218 skf/fag make, housing l type, qty-04 nos, note:- (i)fabrication will be done using prime plates and sections and using mig, welding process. (ii)only tack welding will be done by electrode using arc welding(iii) parallelist of the cross travel rails/square bar, diagonals, deflection of the bridge & trolley will be accurate and confirming to standard and best engineering practices. (iv) bridge must be two coated by red oxide metal primer and two coats of golden yellow colour.11. electric panel for new bridge, resistance boxes for bridge motors, control cabin,12. electric wires, main switch push button control & cable trolleys for complete13. unloader.14. dismantling of old trolly and all its accessories and erection & commission of new trolly, frame and fitting of all old spares ie. rope, drum, thruster break etc complete testing and trail., scope of work1. supply of above mentioned bridge on for basis to mill site.2. dismantling of old unloader. 3.erection of new unloader bridge with old trolley & grab with complete electric work with new electrical panel for bridge and all electrical panel for trolley & grab. all wiring should be new & standard isi make
Tender For corrigendum : daiviya apda work under edsd- rura - carriage of various size pcc poles from store center or from any other place to the respective site of work distence up to 75 km through the kachha pacca road including the work of its loading & unloading at the respective ends also including the work of its dragging etc. and also including the cost of labour, t & p and carrier etc. required for proper completion of work., carriage of various size st poles (9 mtr /11mtr/ 13mtr ) from store center or from any other place to the respective site of work distence up to 75 km through the kachha pacca road including the work of its loading & unloading at the respective ends also including the work of its dragging etc. and also including the cost of labour, t & p and carrier etc. required for proper completion of work., carriage of line material viz. weasel/rabbit/racoon /dog conductor, g.i. earth wire, cross arm, angle, channel, cable boxes, static meter insulators, clamps and other line material from store center or from any other place to the respective site of work through the kachha pacca road including the work of its loading & unloading at the respective ends also including the work of its dragging etc. and also including the cost of labour, t & p and carrier etc. required for proper completion of work., erection of p.c.c double pole including the work of complete h.t. fittings as per respo manual and as per direction of engineer incharge including the cost of labour, t & p and carrier etc. required for proper completion of work., grouting of p.c.c double pole the support shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 including the cost of arrangement of cement, sand, brick ballast/stone ballast, stone pad etc. as per actual site requirement., erection of p.c.c single pole including the work of complete h.t. fittings as per respo manual and as per direction of engineer incharge including the cost of labour, t & p and carrier etc. required for proper completion of work., grouting of p.c.c single pole. the support shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 including the cost of arrangement of cement, sand, brick ballast/stone ballast, stone pad etc. as per actual site requirement., erection of s.t.p single pole including the work of complete h.t. fittings as per respo manual and as per direction of engineer incharge including the cost of labour, t & p and carrier etc. required for proper completion of work., grouting of s.t.p single pole. the support shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 including the cost of arrangement of cement, sand, brick ballast/stone ballast, stone pad etc. as per actual site requirement., erection of s.t.p double pole including the work of complete h.t. fittings as per respo manual and as per direction of engineer incharge including the cost of labour, t & p and carrier etc. required for proper completion of work., grouting of s.t.p double pole. the support shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 including the cost of arrangement of cement, sand, brick ballast/stone ballast, stone pad etc. as per actual site requirement., renozzling of damaged stay set as per respo manual and also including the cost of all grouting material, labour, t & p etc. required for proper completion of work., dismentling of rusted weasal/racoon /dog conductor wire and g.i wire & safe carriage of scrap material back to store as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carries etc. required for proper completion of work., laying, sagging, stringing, binding and jumpering etc. of weasal/dog/rabbit conductor in new erected pole as per respo manual and as per direction of supervising engineer. it includes the cost of labour, t & p, carries etc. required for prope
Tender For e-procurement tender for electrical work first floor - supply & installation service lift db, supply & installation of earthing busbar, copper flexible wire 25 sqmm 1 run for earthing including cable laying and testing, digging 8 feet , 8 ft., gi pipe fixing, 2 x 2 copper plate fixing and 25 x 3 copper strips laying, funnel fixing, putting necessary charcoal and salt, 18 x 18 chamber mason work and miscellenous., indicator 22mm voltmeter lights 220 volt ac ryb (red, yellow, blue), vaf + pf ci 1.0 meter digital panel meter 1a /accuracy class 1 & ct coil, inside distribution board fixing, wiring and termination and lugs crimping and gland fixing and testing, main distribution board wiring and termination and lugs crimping and gland fixing and testing, led panel light fittings 2 x2, led panel light fittings 1 x1, earthing strip or wire, wide cable tray 600x150mm, light points 2 way 1 light for controlled by 2 switches, laying 1.5 sqmm wire 2 run fixing necessary pipe and 2 way switches 2 nos. and boxes plates., cable lugs and cabel gland 25sqmm, white casing pipe 100 x 50 mm, copper flexible cable 1.5sq x 3c including cable laying and testing, circuit 3 phase 6 sqmm + 4 run x 2.5 sqmm 1 run copper wires in 25mm dia fr pvc conduit, armoured cable(25sq x 3.5c) including cable laying and testing, copper flexible cable including cable laying and testing(25sq x 4c), copper flexible cable (16sq x 4c) including cable laying and testing, main circuit 2run x 10 sq.mm +1run x 4.0 sq.mm copper wires in 25mm dia fr pvc conduit, hearting circuit 2run x 4 sqmm + 1run x 2.5 sqmm copper wires in 25mm dia fr pvc conduit, lighting circuit 2run x 2.5 sqmm + 1run x 1.5 sqmm copper wires in 19mm dia fr pvc conduit, industrial switched sockets 63a, industrial switched sockets 32a, heating plug point 16a three pin switched sockets outlet box including providing 16a switched sockets & as required, plug point for 10a three pin switched sockets outlet box including providing 10a switched sockets & as required- - supply & installation, supply of light point controlled by a 10a, sp switch wall chipping, pipe fixing, switch plate fixing and testing- supply & installation
Tender For supply of ptz cameras , led monitor , ip based network thermal imaging cameras , pole mounting stand 10 mtrs , cctv camera power supply , supply, laying of cctv cable in existing cable trenches through pipes , client workstation with graphic card , server with 20tb storage capacity , network switches , 10 kva ups , 24 port l2 or l3 manageable switch , supply of cat-6-utp cable , single information outlet with smb having shutter facility , supply of cat 6 utp patch cord-1mtrs , supply of cat 6 utp patch cord-3mtrs , 24 port cat 6 utp jack panel with cable manager , 6 core sm double sheath, csta, unitube, outdoor cable , sc-lc duplex fibre patch cord , 6 port sm liu fully loaded with 06 simplex sc couplers and 06 sc connector , 19 inch 6u 600mm depth rack with accessories , 42u rack with 1000m depth with accessories , hdpe pipe 32 mm , pvc pipe , casing and capping , supply of gi pipe , fixing of 24 port utp cat6 jack panel , fixing of rack , fixing of liu , digging of hard soil , sc connectorisation per core , fiber laying per meter , laying of utp cable per meter , fixing of information outlet per unit , 2 kva ups with 60 min backup , transceiver , supply of rj-45 connectors as per requirement , newn junction boxes , installation and commissioning charges , turnstiles with door controllers , biometric reader , smart cards , server , software for access control system
Tender For supply of 2 megapixel or above bullet camera , 24 port switch poe as per specifications , biometric fingerprint scanner secugen hamster pro 20 , cat 6a io box with faceplate , cat 6a cable each box 305 mtrs , pvc conduit pipes 2 inches , ip66 outdoor camera boxes , jack panel cat 6a fully loaded 24port , patch cable cat6a 1 meter , patch cable cat6a 5 meter , led industrial monitor 42 inches or above , camera application software with licenses perpetual , higher end server with 32 gb ram 2 tb ssd or hdd for os with 4 gb graphics card and storage of 24 tb hdd usable latest version server os , 24 u floor mounted rack with all accessories exhaust fan power manager and hangers etc , ups 5 kva , soft soil digging , installation testing, commissioning charges for the above