Latest microprobe station Tenders | Government microprobe station Tenders

CTN :45465678

19 Jun, 2026 NA

Kanchipuram - Tamil Nadu

Tender For supply, installation and testing of electronic equipments - supply -ece lab equipments, single output regulated dcvariable power supply- input voltage: 230v / 50hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., dual output regulated dc variable power supply- input voltage: 230v/50 hz ac. output voltage: (0 30)v dc. output current: (0 2)a dc. protection circuit: over voltage, over current, and short-circuit protection. high efficiency: greater than 85%. low ripple and noise: less than 50 mv. digital display., function generator - frequency range: 0.1 hz to 5 mhz. display: 4 to 6 digit led display. output waveforms: sine, triangle, square, pulse, ramp. amplitude: 0 20 vpp. rise time: 100 ns. distortion: 1% within specified frequency range. power supply: 230 v ac 10%, 50 60 hz. output amplifier protection: short-circuit and 15 v, digital ic trainer kit with breadboard - +5 v dc, 1 a regulated power supply. 12 v dc / 15 v dc, 200 ma regulated power supply. solderless breadboard with minimum 840 tie- points,power distribution buses. zif (zero insertion force) ic sockets to accommodate 8 or 16 pin ics. logic input and output leds for output monitoring. 16 buffered led outputs. 16 debounced switch inputs. variable clock generator: 0.5 hz to 50 hz. single pulse output: 100 ms (buffered, positive and negative outputs). one seven-segment display with 4 bcd inputs. built-in logic switches. manual clock: debounced push-button (one pulseper press)., dc voltmeter(digital) - dc digital voltmeter - 3 digit led/lcd display, measurement range: 0 20 v dc,accuracy: class 0.5( 0.5 % full-scale), dc ammeter - dc ammeter digital - 3 digit led/lcd display, measurement range: 0 5 a dc,accuracy: class 0.5 ( 0.5 % full-scale), lvdttrainer kit - ac mains power supply: 230 v 10%, 50 hz. fixed regulated dc power supply: +5 v, 12 v / 500 ma. transducer: lvdt. lvdt displacement: 20 mm (40 mm total). displacement scale: linear 20 mm. displacement display: red color 3 digit led display. excitation frequency: 4 khz. excitation voltage: ac variable excitation voltage up to 5 v., strain gauge trainer kit - ac mains power supply: 230 v 10%, 50 hz metal foil strain gauge mounted on beam/cantilever. strain measurement under applied load. wheatstone bridge arrangement. instrumentation amplifiers with 3 digit display for strain / output voltage. table-top trainer with labelled panel. test points for signal measurement. built-in dc power supplies and wooden closed cabinet. supplied with patch cords and user manual., ask modulation and demodulation kit - message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz, amplitude 5 v. supply voltage (board): +12 v, +5 v dc. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., fpga trainer kit - must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb- uart bridge, usb cable. user manual., measurement scale: a vertical steel meter scale, usually with (1mm) graduations, for precise deflection measurement., accessories: includes a set of slotted weights (e.g., (6times 50g) or similar sets) for incremental loading.

CTN :45430818

12 Jun, 2026 NA

Villupuram - Tamil Nadu

Tender For purcahse of lab equipment for ece -dth trainer kit , fpga/soc development board ,performance of ultrasonic and moisture sensors

CTN :45415530

12 Jun, 2026 NA

Villupuram - Tamil Nadu

Tender For purcahse of lab equipment for ece -dth trainer kit , fpga/soc development board , performance of ultrasonic and moisture sensors

CTN :45404137

16 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For supply of lab equipment for department of electronics and communication engineering - dual output regulated dc variable power supply, function (signal) generator, digital storage oscilloscope, digital ic trainer kit with breadboard, dc voltmeter, dc ammeter, decade resistance box, decade capacitance box, decade inductance box, 8051 microcontroller kit, ask modulator and demodulator trainer kit, dth trainer kit, fiber optic communication demonstration trainer kit, sim reader trainer kit, fpga trainer kit

CTN :45404144

09 Jun, 2026 NA

Palacode - Tamil Nadu

Tender For supply of equipment for electronics and communication engineering department - supply of equipment for electronics and cmmunication engineering department, 8051 micro controller kit :specification : operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., temperaturemeasurementkitspecification : sensors:rtd (pt-100), thermocouple (fe-k/j-type), and/orthermistor (ntc). display: 3 digit led/lcd digital display(typically 200 mv fsd). temperature source: portable water kettle orheater block. signal conditioning: on-board circuitry foramplification, linearization, and cold junctioncompensation. test points: multiple 2 mm / 4 mm banana socketsfor monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntcthermistor probe, k-type thermocouple probe,patch cords and user manual., ask modulationanddemodulation kit:specification : message signal1:8-bit variable data,amplitude 5v. message signal 2:debounced data, amplitude low (0) and high (5 v). message signal 3:fixed data 25 khz, 12.5 khz, 6.25 khz, 3.12 khz,amplitude 5 v. carrier signal: sine wave, frequency 200 khz,amplitude 5 v. modulator type: switching modulator using analogswitch / transistor switching ic. demodulator: envelope detector and lpf. comparator: lm311 based. supply voltage (board): +12 v, +5 v dc. supply current: 100 ma minimum. input voltage: 230 v ac, 50 hz. interface connectors: 2 mm banana socket., dth trainer kit:specification :power supply: 200 v to 240 v ac, 50 hz.dish antenna: 1.5 ft aluminium steerable dish antenna.lnb (low noise block down converter): input frequency: ku-band. output frequency: 950 mhz to 1450 mhz. conversion gain: 65 db. noise temperature: 35 k (max).set-top box receiver in trainer form: if frequency: 70 mhz. video bandwidth: 50 hz to 5 mhz. video output level: 1 vpp at 75 load. video polarity: normal/inverted, switch selectable. audio subcarrier frequency:tunable from 5.0 mhz to 8.0 mhz. remote control provided. hdmi cable: 10 m.controls: channel selection. volume control.fault simulation: five built-in simulated faults for troubleshootingexperiments. if signal disconnected. video output fault. audio mute fault. tuner misalignment. rf output interruption.pcb size: 15" 12" with multicolour section-wise blockdiagram.standard accessories: 1.5 ft dish antenna. lnb. trainer pcb. dish connecting wire. audio-video cable. user manual. acrylic cover. hardware materials for assembly of dish antenna.additional features: dth subscription connection withdoordarshanfree channels. free-to-air channel demonstration., fpga trainer kit:specification : must use industry-standard mid-range fpgadevice usb-jtag programmable, compatible withvivado ise (webpack). power supply: 5 v dc through usb or externaladapter. on-board peripherals: leds, switches, pushbuttons, 7-segment display,clock source, gpio /pmod expansion ports, uart, vga / hdmi, usbuartbridge, usb cable. user manual.

CTN :45368999

16 Jun, 2026 NA

Erode - Tamil Nadu

Tender For purchase of equipment for electronics laboratory – ece department - purchase of equipment for electronics laboratory ece department, single phase induction motor(for technical specifications refer notice inviting tender), auto transformer(for technical specifications refer notice inviting tender), lvdt sensor trainer kit(for technical specifications refer notice inviting tender), strain gauge trainer kit(for technical specifications refer notice inviting tender), fpga trainer kit(for technical specifications refer notice inviting tender)

CTN :45375010

09 Jun, 2026 NA

Nilgiris - Tamil Nadu

Tender For ece lab equipments - fuction generator, dso, dc voltmeter dc voltmeter analog - moving coil - (0-30)v, class 1.0 ( 1 % full-scale) accuracy (1 no) dc digital voltmeter - 3 digit led/lcd display, measurement range: 0 20 v dc, accuracy: class 0.5( 0.5 % full-scale) (1 no) dc voltmeter analog - moving coil - (0-1)v, class 1.0 ( 1 % full-scale) accuracy (1no), dc ammeter dc ammeter analog - moving coil - (0 -500) ma, class 1.0 ( 1 % full-scale) accuracy (1no) dc ammeter analog moving coil - (0-30) ma, class 1.0 ( 1 % full-scale) accuracy (1no) dc ammeter analog - moving coil - (0 - 1000) a, class 1.0 ( 1 % full-scale) accuracy (1no) dc ammeter digital - 3 digit led/lcd display, measurement range: 0 5 a dc, accuracy: class 0.5 ( 0.5 % full-scale) (1no), lvdt sensor trainer kit, auto transformer, fpga / soc development board

CTN :45375057

10 Jun, 2026 3.00 Lacs

Kanyakumari - Tamil Nadu

Tender For purchase of lab items for ece dept. - purchase of lab items for ece dept., dso, 8051 micro controller kit, embedded trainer kit, fpga trainer kit

CTN :45365476

13 Jun, 2026 NA

Tuticorin - Tamil Nadu

Tender For purchase of lab equipments for ece dept - purchase of lab equipments for ece dept, dc voltmeter (digital) (item code : c006) 1.dcvoltmeteranalog moving coil -(0-10)v, class1.0( 1%full- scale)accuracy - 5 nos2.dcvoltmeteranalog- movingcoil-(0-30)v, class1.0( 1%full-scale)accuracy - 4nos, dc ammeter(item code : c007)specifications: 1. dcammeteranalog movingcoil- (0-30)ma,. 5 nos2. dcammeteranalog -movingcoil -(0-1000) a, class 1.0 ( 1 % full-scale) accuracy - 5 nos, decade capacitance box(item code : c0011)specifications: range: 100 pf to 100 f rotary switch selection with 6 dials. maximum voltage: 350 v. accuracy: 1%., decade inductance box(item code : c0012specifications: range:10 hto10h. rotaryswitchselectionwith6dials. low-lossinductors. accuracy: 1%., 8051 microcontroller kit(item code : c0013)specifications: operating voltage: +5 v dc. flash memory: 4 kb (at89c51) / 8 kb (at89s52). ram: 128 bytes internal ram. 16 2 alphanumeric lcd display. push buttons / tactile switches. dip switches for digital input. inbuilt adc interface: ldr, potentiometer. inbuilt dac interface. inbuilt stepper motor driver with stepper motor. inbuilt dc motor driver with dc motor. 1 4 led array, 1 4 keypad, 1 relay. 1 buzzer, 16 2 lcd display, 1 pwm driver. 1 hardware interrupt key, inbuilt rtc. inbuilt eeprom and uart module. 4 7-segment display. supports both assembly and c language programming. pc interfaceable., embedded trainer kit (using lpc2148) (item code : c0014)specifications: cpu - lpc2148, core - 16/32 bit arm7tdmi-s speed - max 60 mhz, flash - 512kb, ram (on chip) 40kb, 46 general purpose i/opins, usb2.0 one 10bit a/d converter with 14 analog inputs, one 10bit d/a converter, six pwm & watchdog two uarts (16c550), two i2c (400kb/s), two spi eight bit digital output, eight bit digital input,16x2 characters lcd and 4x4 matrixkeypad one potentiometer for giving analog input, relay & buzzer interface i2c devices: rtc, eeprom and seven segment display, on board stepper motordriver lm35 temperature sensor, one rs 232 lines are terminated at 9 pin d type connector and usb interface board has inbuilt power supply and mounted in sturdy cabinet accessories usb cable with utility software to download programs from pc to target board power cord, user manual, temperature measurement kit (item code : c0019)specifications: sensors: rtd (pt-100), thermocouple (fe-k/j-type), and/or thermistor (ntc). display: 3 digit led/lcd digital display (typically 200 mv fsd). temperature source: portable water kettle or heater block. signal conditioning: on-board circuitry for amplification, linearization, and cold junction compensation. test points: multiple 2 mm / 4 mm banana sockets for monitoring input/output signals. power supply: 230 v ac, 50 hz, single-phase. accessories: glass thermometer, 10 k ntc thermistor probe, k-type thermocouple probe, patch cords and user manual., fpga trainer kit(item code : c0025)specifications: must use industry-standard mid-range fpga device usb-jtag programmable, compatible with vivado ise (webpack). power supply: 5 v dc through usb or external adapter. on-board peripherals: leds, switches, push buttons, 7-segment display,clock source, gpio / pmod expansion ports, uart, vga / hdmi, usb uart bridge, usb cable. user manual.

CTN :45365499

04 Jun, 2026 NA

Nagapattinam - Tamil Nadu

Tender For purchase of ece lab equipments for lab upgradation - purchase of ece department equipment, digital ic trainer kit with breadboard, 8051 microcontroller kit and interfacing, lvdt trainer kit, strain gauge trainer kit, temperature measurement kit, decade resistance box, decade capacitance box, decade inductance box, fpga trainer kit, dc voltmeter(digital), embedded trainer kit (using lpc2148), dso (digital storage oscilloscope), dc ammeter

Microprobe Station Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors