Get complete information related to latest Microsyringe Tenders . from India at Classic Tenders. Search the best available tenders from Indian government tenders, domestic Microsyringe Tenders , private tenders, online tenders, tender invitation notice, business tender notices, online tenders and bidding Microsyringe Tenders.
Tender For material procurement - material work, stone aggregate(single size): 40+b14:b93 mm nominal size, stone aggregate(single size):20 mm nominal size, coarse sand (zone iii), portland cement, hire charges of concrete mixer 0.25 to 0.40 cum with hopper, vibrator (needle type 40 mm), sundries, wall form panel 1250x500 mm, corner angle 45x45x5 mm 1.50 m long, 100 mm channel shoulder 2.5 m long, double clip (bridge clip), single clip, m.s. tube 40 mm dia, twisted steel/deformed bars, stone aggregate(single size): 10 mm nominal size, stone for masonry work, solid blocks of size 30x20x20cm, wall form panel 1250x450xmm, corner angle 45x45x5 mm 2.50 long, column clamp 450x1070 mm, prop 2 m (2-3.5m), structural steel such as tees, angles, channels and r.s. joists, red oxide zinc chromate primer, adjustable telescopic prop 3 m (2.02-3.75m), beam clamp 300-380 mm (450-1070 mm), second class kail wood in planks, second class kail wood in scantling, hollock ballies 125 mm diameter, adjustable span eso+si (2.35-3.40), solid blocks of size 30x20x15cm, mild steel tubes electric resistant or induction butt welded, mild steel round bar 12 mm dia and below, flats up to 10 mm in thickness, bright finished or black enameled mild steel butt hinges 100x58x1.90 mm, factory made glass reinforced plastic door frame 90x45 mm i/c carriage, 30 mm thick factory made glass fiber reinforced plastic panel door shutter i/c carriage, powder coated m.s. butt hinges 100 mm x58 mm x 1.9 mm, bright finished or black enameled mild steel screws 40 mm, bright finished or black enameled mild steel screws 20 mm, float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm), pvc pipe 110 mm outer dia 6kgf/cm2, pvc pipe 15 mm outer dia 10kgf/cm2, pvc pipe 32 mm outer dia. 10kgf/cm2, pvc pipe 40 mm outer dia. 10kgf/cm2, pvc pipe 63 mm outer dia . 6kgf/cm2, pvc vent cowl 63 mm dia, pvc vent cowl 110 mm dia, brass bib-cock-15 mm dia, pvc elbow 63 mm dia, pvc 45 degree elbow 63 mm dia, pvc door elbow 63 mm dia, pvc bend 63 mm dia, pvc tee 63x63x63 mm dia, pvc socket/coupling 63 mm dia, pvc elbow 110 mm dia, pvc 45 degree elbow 110 mm dia, pvc door elbow 110 mm dia, pvc bend 110 mm dia, pvc tee 110x110x110mm dia, pvc socket/coupling 110 mm dia, pvc pipe 25 mm outer dia . 12 kgf/cm2, vitreous china orrisa type w.c. pan size 580 mm, flushing cistern p.v.c. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe), 100 mm s.c.i. trap with vent heel, black plastic seat (soild) with lid c.p.brass hinges and rubber buffers, vitreous china pedestal type wate closet, vitreous china flat back wash basin 550x400 mm, 15 mm c.p.brass tap, c.p. brass waste 32 mm, c.i. bracket for wash basin and sinks, stainless steel kitchen sink - without drain board 470x420 mm bowl depth 178 mm, semi rigid pvc waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c pvc waste fittings, polyethylene water storage tank with cover and suitable locking arrangemnet, fine sand (zone iv), vitrified floor tile 60x60 cm, ceramic glazed tiles ist quality minimum thickness 5 mm in all colours shades and designs except burgundy, bottle green black, ceramic glazed tiles ist quality 300 x 300 mm in all shades and designs of white, ivory, grey, fume red brown etc., multi surface paint, special primer (c.w), black japan, synthetic enamel paint in black or chocolate shade, mild steel plates, g.i. pipes 40 mm dia, mild steel round bar above 12 mm dia, welding by electric plant, stainless steel (grade - 304) hollow section round/square tubes, stainless steel bolts /square bar and plates
Tender For material supply for works in mgnregs action plan - material supply for mgnregs individual and common asset creation - stone aggregate:40mm nominal size, stone aggregate:20mm nominal size, stone aggregate:10mm nominal size, stone aggregate:06mm nominal size, course sand(zone3), portland cement, concrete mixer, vibrator, stone for masonry work, twisted steel/deformed bars, structural steel such as tees,angles,channels and r.s joists, second class kail wood in planks, second class kail wood in scantling, wall form panel 1250*450mm, corner angle 45*45*5mm 2.5long, column clamp 450*1070mm, prop 2m(2-3.5m), laterate stone of size 40*20*15cm, solid block of size 30*20*15cm, mild steel plates, mild steel rivets, flats up to 10mm in thickness, 20 mm dia.holding down bolts, mild steel sheets for tanks, galvanised wire mesh, iron pintels including welded pin, mild steel sheets with bolts and nuts, mild steel hooks, gi trafford profile sheet 0.35mm thick, galvanised steel jor l hooks 8 mm dia, galvanised steel bolts and nuts 6mm dia and 25mm long round head with slots, wire nails, fine sand, pvc pipe 63 mm outer dia., pvc bend 63 mm dia., pvc pipe 110mm outer dia., pvc elbow 63 mm dia, pvc tee 63*63*63 mm dia, pvc end cap 63 mm dia, pvc reducer 63*50mm dia, pvc pipe 160mm outer dia., gi pipes 50 mm dia., gi pipes 40 mm dia, quarry waste, precoated galvanised plain ridge, vitrified floor tile 60*60cm, welding by electric plant, hire charge of 10hp engine and pump set, diesel oil, 200 mm aluminium aldop, pvc socket/coupling 63 mm dia, polythene water storage tank, red oxide zinc chromate primer, deharadun white lime, smooth wheeled roller 8 to 10 tonne, water tanker 5 to 6 kl capacity, interlocking c.c. paver block (80 mm thick, m-30), sundries
Tender For supply of materials and erection for shifting of control room pannel at 33/ 11 kv sub station bharsawa distt. kaushambi under deposit scheme on "semi turnkey basis" under edc, kaushambi - name of work: supply, carriage & erection of materials for control room pannel shifting of shiffting of 33/11 kv s/s bharsawa distt. kaushambi, supply of de-centralised materials, 11 kv 3x120 mm2 xlpe cable jointing kit o/d & i/d, control cable 4x2.5 mm2, control cable 2x2.5 mm2, g.i. pipe 6 " dia, rubber matting, clamp with nut & bosts, earth wire clamp for pcc pole, stay clamp for pcc pole, top channel clamp pcc pole, dropper channel clamp pcc pole, g.i. strip 35x6 mm, carriage of following material, pcc pole 8.5 mtr. long., structure of la, 33kv isolator, 33 kv cts, single t/f control pannel, 33kv vcb,11 kv outgoing. incoming pannel, battery & battery charger and other associated accessiories etc. (availibility at concern store center of store division), erection work, installation of 33 kv single transformer control pannel 2 no., incoming 2 no. and 7 no. outgoing in the switchgear room and grouting the pannel by rag bolt using cement, sand mortar in ratio 1:3. work includs fitting of all accessories in all respect with complete connection of control cable with pannel. all material will be provided by the contractor except vcb and crp., construction of cable trenchs with top cover and laying of control cable for vcb, c.t. & t/f control pannel etc. as per direction of engineer. trenchs to be 12 wide and 9 deep. work includes digging, of trench, concreting of the foundation in the ratio 1:3:6 r.b. wall 9 wide with cement mortar 1:4 and plastering inside the trench in the ratio 1:3 and sand filling in the trench. all material will be provided by the contractor., earthing of 11 kv indoor equipments, switchgears as per resspo drawing. with g.i. strip of size 35x6 mm. g.i. strip fully welded at both ends and to be connected with earthmat,, erection of dp with pcc pole 8.5 mtr long with all accessaries and grouting of the pcc pole with cement, sand and brick ballast ratio 1:4:8 size 0.45x 0.45x 1.5 mtr deep under the ground as per drawing no. res-6.(cement, sand, brick, ballast shall be provided by the contractor.), installation of 24 volt battery and battery charger with cabinet in the switch gear room, by grouting base channel 100 x 50 x 6 x 1000mm. fixing of rag bolt., laying of 11 kv 3x300/3x185/ 3x120 sqmm. xlpe cable by digging 0.75 mtr. deep trench, putting layer of sand in the bottom, ramming it, laying of cable over it rmt and covering the cable from sides and top by laying bricks, finally covering the same by earth and levelling of the same, all the materials, except cable, will be pvovided by the contractor., fixing and termination of outdoor/ indoor heat shrinkable cable boxes of size 3 x300/3x185/3x120 sqmm. xlpe cable. boxes will be supplied by the contractor, sundries ( as per site requirement/emergency work), safe dismantling of 11 kv o/g pannel & received back to store, laying of weasel conductor with the help of aluminium roller by hanging three nos. on each support in a manner taking sufficient care to ensure safety of weasel conductor against rubbing on ground, precaution for safety of crops is also to be taken. the work includes jointing of conductor by providing jointing sleaves, stringing of conductor upto correct sag and binding of conductor with insulators on each support. all material shall be provided by contractor such as jointing sleeve binding wire, armour rod etc.
Tender For supply of materials and erection for shifting of control room pannel at 33/ 11 kv sub station bharsawa distt. kaushambi under deposit scheme on turnkey basis under edc, kaushambi - name of work: supply, carriage & erection of materials for control room pannel shifting of shiffting of 33/11 kv s/s bharsawa distt. kaushambi, supply of centralised materials, 11 kv switch gear 600/300/5a 350 mva i/c, 11 kv switch gear 200/100/5a 350 mva o/g, 11 kv 3x300 mm2 xlpecable, 11 kv 3x120 mm2 xlpecable, 24 volt battery, 24 volt battery charger, pcc. 8.5 mtr. long for feeder, 11 kv tpmo switch with fixing clamp, 11 kv top channel, 11 kv dropper angle, earthing complete, stay set complete, 11 kv polymer pin insulator, 11 kv polymer disc insulator, 11 kv disc fiting, 33 kv control panel t/f, acsr weasel conductor, supply of de-centralised materials, 11 kv 3x120 mm2 xlpe cable jointing kit o/d & i/d, control cable 4x2.5 mm2, control cable 2x2.5 mm2, g.i. pipe 6 " dia, rubber matting, clamp with nut & bosts, earth wire clamp for pcc pole, stay clamp for pcc pole, top channel clamp pcc pole, dropper channel clamp pcc pole, g.i. strip 35x6 mm, carriage of following material, pcc pole 8.5 mtr. long., structure of la, 33kv isolator, 33 kv cts, single t/f control pannel, 33kv vcb,11 kv outgoing. incoming pannel, battery & battery charger and other associated accessiories etc. (availibility at concern store center of store division), erection work, installation of 33 kv single transformer control pannel 2 no., incoming 2 no. and 7 no. outgoing in the switchgear room and grouting the pannel by rag bolt using cement, sand mortar in ratio 1:3. work includs fitting of all accessories in all respect with complete connection of control cable with pannel. all material will be provided by the contractor except vcb and crp., construction of cable trenchs with top cover and laying of control cable for vcb, c.t. & t/f control pannel etc. as per direction of engineer. trenchs to be 12 wide and 9 deep. work includes digging, of trench, concreting of the foundation in the ratio 1:3:6 r.b. wall 9 wide with cement mortar 1:4 and plastering inside the trench in the ratio 1:3 and sand filling in the trench. all material will be provided by the contractor., earthing of 11 kv indoor equipments, switchgears as per resspo drawing. with g.i. strip of size 35x6 mm. g.i. strip fully welded at both ends and to be connected with earthmat,, erection of dp with pcc pole 8.5 mtr long with all accessaries and grouting of the pcc pole with cement, sand and brick ballast ratio 1:4:8 size 0.45x 0.45x 1.5 mtr deep under the ground as per drawing no. res-6.(cement, sand, brick, ballast shall be provided by the contractor.), installation of 24 volt battery and battery charger with cabinet in the switch gear room, by grouting base channel 100 x 50 x 6 x 1000mm. fixing of rag bolt., laying of 11 kv 3x300/3x185/ 3x120 sqmm. xlpe cable by digging 0.75 mtr. deep trench, putting layer of sand in the bottom, ramming it, laying of cable over it rmt and covering the cable from sides and top by laying bricks, finally covering the same by earth and levelling of the same, all the materials, except cable, will be pvovided by the contractor., fixing and termination of outdoor/ indoor heat shrinkable cable boxes of size 3 x300/3x185/3x120 sqmm. xlpe cable. boxes will be supplied by the contractor, sundries ( as per site requirement/emergency work), safe dismantling of 11 kv o/g pannel & received back to store, laying of weasel conductor with the help of aluminium roller by hanging three nos. on each support in a manner taking sufficient care to ensure safety of weasel conductor against rubbing on ground, precaution for safety of crops is also to be taken. the work includes jointing of conductor by providing jointing sleaves, stringing of conductor upto correct sag and binding of conductor with insulators on each support. all material shall be provided by contractor such as join
Tender For supply of materials for mgnregs works in various wards of varapuzha grama panchayath - supply of materials, stone for masonry work, through and bond stone size 24 x 24 x 39cm, sundries, stone aggregate(single size):20 mm nominal size, stone aggregate(single size): 10 mm nominal size, coarse sand (zone iii), portland cement, hire charges of concrete mixer 0.25 to 0.40 cum with hopper, vibrator (needle type 40 mm), wall form panel 1250x500 mm, 100 mm channel shoulder 2.5 m long, double clip (bridge clip), single clip, m.s. tube 40 mm dia, double clip (bridge clip), single clip, m.s. tube 40 mm dia, smooth wheeled roller 8 to 10 tonne, water tanker 5 to 6 kl capacity, water, well graded material for sub base grading i, 53 mm to 9.5 mm below @ 50 percent, well graded material for sub base grading i, 9.5 mm to 2.36 mm below @ 20 percent, well graded material for sub base grading i, 2.36 mm below @ 30 percent, interlocking c.c. paver block (80 mm thick, m-30), stone aggregate(single size): 06 mm nominal size, stone aggregate(single size): 40 mm nominal size, second class kail wood in planks, second class kail wood in scantling, twisted steel/deformed bars, solid blocks of size 30x20x15cm, fine sand (zone iv), mild steel tubes hot finished welded type, red oxide zinc chromate primer, welding by electric plant, synthetic enamel paint in black or chocolate shade, gi trafford profile sheet 0.35mm thick, bitumen washer, g.i limpet washer, galvanised steel j or l hooks 8 mm dia, galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots, pvc pipe 63 mm outer dia . 6kgf/cm2, pvc bend 63 mm dia