Tender For supply of 1. 3ton capacity flt with fuel and drivers (01 flt with rotary fork attachment , 01 flt with 6 meters lifting height and three sets of fork extensions of appropriate sizes as per the field requirement) - 08 nos for 312 days. 2. 06 ton capacity flt with fuel and driver (01no.-6 meters lifting height and twosets of fork extensions of appropriate sizes as per the field requirement)- 01 nos for 312 days. 3. mobile crane with 16mt capacity with fuel, driver and lifting tackles, wire ropes, chains, etc. - 01 no for 312 days.4. jcb with fuel and driver with front loader and backhoe with bucket attachment - 01 no for 100 days. 5. high reach stacker (capacity- 1600 kgs) with driver specification: lift height of 7500mm and three stage mast with closed height below 3100 mm( similar to yale model mr-16)- 01 no for 312 days. 6. assistants (i.e. four assistants with each 3ton & 6ton flts and two assistants with jcb and 16 mt mobile crane) i.e. (9 x 4) + (2 x 2) = 40. the rate for labour is fixed. (i.e. rs.902/- for unskilled labour as per minimum wage notice of chief labour commissioner for industrial workers duly considering the average increase during the contract period plus pf, epf, edli, etc.) - 40 nos for 312 days. 7. supervisor the rate for labour is fixed. (i.e. rs.1083/- for skilled labour as per minimum wage notice of chief labour commissioner for industrial workers duly considering the average increase during the contract period plus pf, epf, edli, etc.) - 01 nos for 312 days. (this will change during the contract period as and when the minimum wage is revised as per the calculation specified in the tender document) kindly see the detailed description in the scope ofwork, special conditions of contract in documents attached. the tenderer should quote total value for oneset in ireps duly attaching unit rate against each schedule of item and value against each including total value and should be attached along with the offer . ]
Tender For supply of carbide tipped blade chain saw - conforming standards for the item - en/din/us/equivalent standards, type of engine- 2 stroke petrol driven air cooled, displacement-79 cc, output power - 5.5 hp, engine speed at no load - 10500 rpm, type of fuel - petrol, fuel tank capacity - 0.7l, ignition system should be electronic with preferably one button start up, fully automatic and adjustable chain lubrication system, automatic chain brake system for quick stoppage when required, air filteration system for petrol engine, type of blade - carbide tipped blade, length of guard bar- 16 inch (one piece construction), adjustable depth of cut ? 6 inch, full blade guard with adjustable depth limiter in inches - 8 (minimum 1 cm adjustment), chain speed- 25 meter per second, adjustable depth of cut - 06 inch, weight of carbide tipped chain saw- 6.3 kg, cutting chain detail- carbide tipped chain with 3/8 pitch with heavy duty tie straps and tempered rivets, protective carry case should be supplied with the machine, copies of test certificates and certifications as applicable to be furnished to buyer on demand at time of supplies, demonstration of equipment and training to be provided after completing supplies,make: makita-ea7900p45e/ hikoki/ dewalt, warranty- 03 years (oem). ]
Tender For supply of fuel oil gauge dlw. drg. no. 792 v 11342 alt. "f" or latest. (dlw pt.no.11440417) along with all part drgs. [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]
Tender For supply of fuel injection pump bosch part no.9410035001. [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variationpermitted: max 8 lacs ] ]
Tender For tender for supply of pressure transmitter , o ring , locking screw , loctite 601 , conditional actuator safeties card , overspeed detection card , bearing for timing gear , bevel pinion , o ring , gasket joint , v belt a49 , valve guide , expansion bellow , o ring - exh valve guide 60 c7 id18x2.5 , press switch set at 1.5bar mode pe2.5 , pressure transmitter , set bolt m27 item no 203 , gfl nut , washer , valve relief assy , set bolt m24x3x140 8.8 , screw set , nut , allen screw , circlip external 19mm , banjo boltm12x1.5 , washer plain , washer copper , copper washer 18x24 , washer copper , washer copper , worm drive hose clip 30mm , conical spring washer , disc spring , spherical brg assembly , main bolt , links , spacer , cap screw position 40 , spring washer position 41 , overload roller , cap screw position 80 , main bearing assly , eccentric shaft , pinion , punched gasket , flexmast coupl pipe 88.9mm o.d 096500v3.650 , circlip internal , flexmast conn gm10006 038 38 od pipe , joint , key for damper , damping bush , fuel feed pump del suction conn , sleeve dn32 pn16 , sleeve dn200 pn16 , rubber compensative sleeve dn150 pn16 , element for lo thermostat 63 71 deg c , o ring an28 , oil level contact type 20007 , speed sensor 19050 , rubles compens sleeves dn50 pn16 lf130 , injection pump assly dia23 grad , 2 way pneumatic valve , o ring 05x260 , main bolts , temp sensor rtd pt100 mbt 2 s 80 1/2 fie dgf , overspeed air intlet connection , governor control air inlet connection , fuel rack position limiter air inlet connection , flow switch , pressure switch xml bso4b2s11 , sleeve nt1 cc pn16 dn40 av cb , spacer , gasket , addesive super cyano 495 , metallic gasket , corrugated metallic joint , expansion bellow , pressure reducer 30 7 bar , filter pad set fx4000 , lid seal for fx4000 , tie rod , bush , bush , lgc pin lgc g5 8x30 , group small end bearing , o ring , bush , roller valve gear bar , valve guide , snap ring , sealing ring an 13 60c7 , stud , spring collar , spring , o ring ms29-513/126 21a7 nse 6.531 , nozzle injector , injector nozzle , needle , safty valve on cyl. head , pin for rack bar , link for rack , valve feed , spring , coupling holder , top spring collar , scale shim bar , serrated pin , positioning pin , filter oil fuel pump 1set 16nos , adjusting screw bar , o ring , metafram bush bp25 16/20x20 , ball bearing skf 6307 , shim for gov control , spacer bar , o-ring an 49 nse6.5 60c7 , o ring anno 53 nse 6.5 60 , bearing roller , water pipe gasket , retaining valve rk44dn65 , seal housing flange , o ring , o ring , spring collar bar , gasket , o ring no18 nse6.5 60c7 , loctite 573 , gasket , particle detection filter , b.s.ring type c30 nse6.51 20a8 , thermocouple for turbocharger , fuel filter element , o ring 162x8 , nut for shaft , limit switch for gachot valve , protect cyl head tie rod , guide piece f valve gear , lock washer pair , dome nut m30x2 , piston ring p3712 , pneumatic distributor pneu/pneu , inlet valve seat , solenoid valve safety stop , hexagon bolt , ht water pump assly cw , o ring ms 295 13/245 60c7 viton , ring spanner for nuts 17 19 22 24 46 50 mm , solenoid over speed air , pressure regulator , pressure transmitter 10 bar 24vdc o/p-4-20 ma , gasket , exhaust valve seat , bush , displaying and protection module , illuminated blue push button 2no , hexagon bolt , o ring an53 60c7 , o ring kalrez , set bolt m30 x 3.5 , joint 65x65x2mm , ball bearing skf 6212 , o ring-exh valve guide-60 c7 id 18x2.5 , actuator safeties card , gasket , starting air hose assly , pressure switch 2.5-28 bar , regr safeties temp card rsp card , pressure transmitter 6 bar 24vdc o/p-4-20 ma , oil seal for fuel booster pump 16x40x10 , bs ring-bsb d12 nse6.51 20a8 , piston , nut , roller bearing 110 60 22 , bush , socket for pressure sensor or switch , air filter , power switch , field communication module 170fnt11001 , illuminated green push button 2no , gasket , sensor for exh temp tc , filter for pressure redu
Tender For supply of coke dust/powder (fine carbonaceous material derived from the screening or grinding of metallurgical coke), required for open hearth furnace operations as a fuel and reducing agent. form : fine powder / dust. particle size : passing through 4 mm sieve. grade : any grade of foundry coke. packing : 25 - 50 kg plastic bags. [ warranty period: 30 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted: max 8 lacs ] ]
Tender For supply of fuel filter, for t-28 machine. part no.: 3531-0032a, make- sun-vm motori, hsn code.: 84212300, annual maintenance contract no.: 96, [ warranty period: 6 months after the date of delivery ][quantity tolerance (+/-): 5 %age , item category : normal , total po value variation permitted:max 8 lacs ] ]
Tender For tender for supply of control valves - fuel oil flow control valve as per boq line item 1 , pyrolysis fuel oil flow control valve as per boq line item 2 , fuel gas flow control valve as per boq line item 3 , spray control valves as per boq line item 4 , steam to sb pressure control valve as per boq line item 5 , cbd level control valve as per boq line item 6 , atom steam pres cont valve as per boq line item 7 , mandatory spares as per boq line item 8 , commissioning spares as per boq line item 9