Latest motor parts scrap Tenders | Government motor parts scrap Tenders

Central Government/Public Sector

CTN :45102682

18 May, 2026 NA

Ambala - Haryana

Tender For supply installation testing commissioning of dg set, 10 kva, 3 phase, 415 volts, 10.4 amp, 50 hz, 1500 rpm, air/liquid cooled diesel engine. kirlosker. type da 01. suitable for lifting plateform of 8 wheeler tower wagon.make- kirlosker, general motor volvopanta , with remote sencering system. or better or similar firm should integrated the item with existing system [ warranty period:30 months after the date of delivery ]

Central Government/Public Sector

CTN :45102860

01 Jun, 2026 NA

Chennai - Tamil Nadu

Tender For provision, commissioning and testing of existing igbt-based three-phase propulsion (medha) non-ac motor coach for conversion into ac-enabled coach, including mounting and installation of rmpus, supply andfitment of stainless-steel trough assembly below rmpus, air-distribution ducting, and drain-water pipe arrangement to ensure zero leakage into passenger area, as per enclosed specification/annexure. note: rmpus, control panel, and necessary roof-wiring cables will be supplied by railways. prior approval of coach ga drawings for rewiring and modification shall be obtained before commencement of work. [ warranty period: 30 months after the date of delivery ]

State Government

CTN :45095860

21 May, 2026 5.60 Lacs

Navsari - Gujarat

Tender For drilling 200 mm dia up to 60 mtrs deep tube well by dr drilling rig supply, installation, testing and commissioning of three phase sub pump motor set with assigned electro-mechanical acessories at police housing board eru, ta- jalalpor, dist. navsari under deposite work 2025-26

Central Government And Public Sector

CTN :45104682

12 May, 2026 NA

Bangalore - Karnataka

Tender For magnetic drum separator (double stage type) conforming to model/part no. efe-rwf-md-00 of electro flux equipments pvt ltd or model/part no. pml-917134510 of permanent magnet ltd or model/part no. bmx-369/1 of wesman engineering company pvt ltd, with the following specifications: technical specifications: 1. type of magnet: high power high gradient rare earth magnet (nd-fe-b) 2. magnet grade: n50 3. magnetic strength: minimum 3000-3500 gauss or higher at drum surface 4. maximum operating temperature: 80 deg c 5. separation efficiency: minimum 90% (preferably up to 95% or above) 6. drum material: stainless steel (ss) 7. drum diameter: 300 mm 8. drum width: 600 mm 9. number of drums: double10. drum surface hardness: 500-700 vickers drive system: 11) geared motor: 1.0 hp x 2 nos, 1440 rpm, 415v +/- 10%, 50 hz, 3 phase, continuous duty (s1), insulation class f or better 12) make of geared motor: premium make such as sew / bonfiglioli / nord or equivalent make 13) drive type: v-belt and pulley note: the supply consists of 1.complete unit with base frame, guards, fasteners and all accessories required forinstallation 2.suitable for continuous heavy-duty industrial operation 3. proper sealing arrangement to prevent dust ingress 4. anti-corrosive painting (except ss parts) 5. nameplate indicating model, serial number, year of manufacture and technical details (a) the bearings should be procured from authorised dealers and should be of skf/fag/ntn / timken / ina make only. (b) the firm should furnish bearing inspection certificate from manufacturers or their authorised testing agents along with the supply. (c) magnet strength certificate (gauss report) from manufacturer or nabl accredited lab to be furnished along with the supply. (d) material test certificate (mtc) for drum from nabl accredited lab to be furnished along with the supply. (e) warranty: warranty shall be 18 months from date of supply or 12 months from commissioning, whichever is earlier. (f) makes : electro flux / wesman / permanent magnet ltd only. [ warranty period: 18 months after the date of delivery ]

CTN :45123879

30 May, 2026 40.35 Lacs

Khorda - Odisha

Tender For supply installation testing and commissioning of pump motor sets required for pump houses and stps at aiims bhubaneswar

CTN :45101283

11 May, 2026 NA

Malda - West Bengal

Tender For supply of supply, installation, testing and commissioning of industrial grade high performance desert cooling system which enhanced humidity upto 30% to reduce dry heating effects, the unit must include a compatible motor (copper based), corrosion resistant housing, suitable for invertor operation and non- corrosive body. [ warranty period: 12 months after the date of delivery ]

CTN :45120113

29 May, 2026 NA

Kanpur - Uttar Pradesh

Tender For supply of manufacture & supply of h. s. c. centrifugal pump 25cusec capacity and 32mtr head, complete with base , supply of suitable 3.3 kv ht squirrel case induction motor at stage-1 of umarahat pump canal phase-1 , supply of suitable 3.3 kv ht vcb panel (1 incomer+ 3 outgoing) at stage-1 of umarahat pump canal p , supply of suitable pipe reducers in suction side of sluice valve & pump suitable pipe expander in de , installation, testing & commissioning of above equipment at stage-1 , manufacture & supply of h. s. c. centrifugal pump 50cusec capacity and 22mtr head, complete with base , supply of suitable 3.3 kv ht caca induction motor at stage-2 , supply of suitable 3.3 kv ht vcb panel (1 incomer+ 1 outgoing) at stage-2 , supply of suitable pipe reducers in suction side of sluice valve & pump, suitable pipe expander in d , installation, testing & commissioning of above equipment at stage-2 , supply of suitable 3.3 kv ht capacitor at stage-1 & stage-2 of umarahat pump canal phase-1.

CTN :45099179

27 May, 2026 NA

Shahapura - Rajasthan

Tender For supply of thermometer digree , series test lamp , knife switch dpdt fuse terminals , knife switch tpdt fuse terminals , miniature circuit breaker mcb , earth plate copper , earth plate , earth electrode copper , mccb , elcb , rccb , fuse hrc type , fuse glass type , fuse rewire type , rheostat sliding type 0 to 25 2a , rheostat sliding type 0 to 300 2a , rheostat sliding type 0 to 1 10a , rheostat sliding type 0 to 10 5a , capacitor electrolytic type , capacitor ceramic type , capacitor polyester film type , capacitor variable type , capacitor dual run type , lamp halogen incandescent type , lamp fluorescent tube type , hp lamp mercury vapour , hp lamp sodium vapour , lp lamp sodium vapour , lamp led , plug socket piano switch lamp holder , cables , bus bar brackets , rubber mat thick , electrician helmet , rcc pole accessories lt line , safety belt , ohm meter series type , ohm meter shunt type , digital multimeter , voltmeter multirange , milli voltmeter centre zero , ammeter mc ma portable lab type , ammeter mc portable lab type 0 to 5 a , ammeter mc portable lab type 0 to 25 a , ammeter mi portable lab type 0 to 1 a , ammeter mi portable lab type 0 to 5 a , ammeter mi portable lab type 0 to 25 a , kw meter analog , digital wattmeter , energy meter single phase , energy meter three phase , three phase power factor meter digital , frequency meter , magnetic flux meter , lux meter , tachometer analog , digital tachometer photo sensor , tong tester clamp meter digital , megger , 3 point starter , 4 point starter , wheatstone bridge galvanometer battery , single phase variable auto transformer , phase sequence indicator , growler , resistance type starter , direct on line dol starter , star delta starter manual , star delta starter semi automatic , star delta starter fully automatic , soft starter 3 phase , auto transformer type starter , oscilloscope dual trace , function generator , soldering iron 25w , soldering iron 65w , soldering iron 120w , temperature controlled soldering iron , discrete component trainer , linear ic trainer , digital ic trainer , electric hot plate induction type , electric kettle , electric iron , immersion heater , ceiling and table fan , geyser storage type , mixer and grinder , washing machine , motor pump set 1 hp , oil testing kit , inverter input output battery , voltage stabilizer input output , power supply , battery charger , current transformer , potential transformer , solar panel battery , computer system , laser printer , manual motor coil winding machine step arbor , ceiling fan coil winding machine , primary current injection set , smart meter single phase , smart meter three phase , ev charger 3 phase , ev charger home single phase , working bench , wiring board projection , instructors table , instructors chair , metal rack , lockers drawers , almirah , black board white board , fire extinguisher , fire buckets , turnkey execution of electrician lab setup measuring steel tape- specification not available, combination plier insulated 200 mm- specification not available, screw driver 4150 mm diamond head- specification not available, screw driver insulated 6150 mm- specification not available, electrician screw driver - specification not available, heavy duty screw driver insulated- specification not available, electrician screw driver- specification not available, punch centre- specification not available, knife double bladed electrician - specification not available, neon tester 500 volt- specification not available, steel rule 300 mm (metric & english)- specification not available, hammer cross peen 250 gm- specification not available, hammer ball peen 500 //bid details 2 / 130 gm- specification not available, pincer 150 mm- specification not available, clamp 'c' 100 mm- specification not available, clamp 'c' 200 mm- specification not available, spanner 150 mm adjustable drop forged ss- specification not available, spanner 300 mm adjustable drop forged ss- specification not avail

CTN :45127699

14 May, 2026 62.0 Thousand

Jaipur - Rajasthan

Tender For supply, installation, testing and commissioning of submersible motor at hawa mahal, jaipur.

CTN :45118218

06 Jun, 2026 NA

Bhagalpur - Bihar

Tender For supply, installation, testing and commissioning of fully automatic cnc celing fan motor winding machine with digital display counter, single drive single head, main motor (ac): 1hpx1, power source : 220 volt ac (+/-10%), 50hz, single phase, maximum speed: 100-4500 rpm, indexing motor, traverse motor - stepper motor, traverse motor- stepper motor, no. of spindle: 1, stator dimension: 35 mm-180mm, stator thickness: 8mm-36mm, wire size 29 swg to 37 swg, dimension of m/c: 400x750x750 mm (approx) with 14 pole die, similar to model : kddk-149, make kddk/techno/vew or similar. [ warranty period: 30 months after the date of delivery ]

Motor Parts Scrap Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government/Public Sector

State Government

Central Government And Public Sector