Latest motor shaft Tenders | Government motor shaft Tenders

CTN :45519945

22 Jun, 2026 37.35 Lacs

Chhabra - Rajasthan

Tender For requirement of spares of m/s ingersoll rand make conveying air compressor model r-160i-x 7.5wc and up5-22-7 for dry fly ash dense phase system,unit#3 and 4, ctpp, chhabra - model no. r160i-x7.5 wc, seal, shaft high pressure part no. 89292445, element, seprator tank 18 inch part no. 23566938/ 23545841, oil cooler, water cooled part no.23572415, after cooler, water-cooled part no.23572423, cap screw m6x25 soc hd cap w/nylon insert part no.22168710, pressure transducer 0-225 psig part no.47545275001, pressure transducer 0-15 psig part no.47560902001, assembly gear set 160 kw single stage 7.5 bar part no.23521859, pin dowel [motor] part no.39194915, pad pre filter part no.23523772, actuator service kit part no.23467251, inlet valve part no.23421217, elbow 1/4" 90 degree straight thread ms part no.96757604, spacer gear (ce177g) part no.39326483, sleeve motor shaft 4.25 od m132/160 part no.89292478, key,square both ends 0.88sq x1.25 part no.95135638, valve in line check part no.23453020, tube gear case scavenge part no.23453129, air cleaner assembly nlg37-42 pico standard part no.23390156, ultra coolant (208 litres) drum part no.39433743, key, rect one round end part no.96759212, clamp, plate part no.35295336, screw, socket head part no.32555819, housing, seal part no.22880744, gasket, gear case part no.39454558, pin, dowal [air end] part no.35295336, valve, orifice [separator tank] part no.23449200, oil filter assembly part no.23523434, o ring set part no.ok002222, pressure transducer cable part no.23529373, temprature sensor part no.23522246, valve min press check 132-160 kw part no.23521297, 5sv solinied cable part no.23562432, model no. up5-22-7, element coolant filter part no.54672654, element seprator 194cfm (spin-on) part no.54749247, pad pre filter part no.22053722, element air filter part no.89295976, kit, inlet valve repair part no.22067177, kit-mpcv part no.22064695, kit thermal valve repair part no.22393326/ 22832885, valve solenoid 125 inch npt part no.54774302, valve solenoid 1/2 in npt 110 volt part no.54654652, spring gas part no.54749114, elbow .31tx .50sae part no.95993572, elbow , 90deg male 37a10c3xz2 part no.95937686, tube oil feed (rear bearing) part no.85581858, tube, vmc block to bare part no.85581866, belt part no.89265052, ultra coolant (20litres) drum part no.38459582, tempreture sensor part no.22137848, conteroller part no.22128763, tube nylon part no.39124813, tube nylon part no.39124821, elbow part no.39155650, elbow part no.39155577, nipple part no.22354989

CTN :45488935

30 Jun, 2026 41.38 Lacs

Murshidabad - West Bengal

Tender For procurement of esp spares for unit 4 esp overhauling during under ahp-em,stage ii during 2026,sgtpp - procurement of esp spares for unit 4 esp overhauling during under ahp em ,stage ii during 2026,sgtpp, ci bearing,collecting rapping ( plain bearing (ci) for crm & erm system,mat-is-210 gr-20 with 02 nos bolt, id-51 mm and 50 mm thickness. ), ci bearing for erm vertical shaft for esp dia-40mm. ( bush along with outer assembly. ), set ring for bush bearing for esp for 500mw esp, thrust bearing of em vertical rapping shaft ( mat-en-8. ), bottom bearing # of em rapping vertical shaft, major pin wheel big ( mat- pin en-8 with hardness -300-350 bhn, body-is-2062(assly). ), minor pin wheel small ( mat- pin en-8 with hardness -300-350 bhn, body-is-2062(assly). ), heating element for esp hopper for esp for 500mw esp. ( 440vac,for 500mw bhel esp, rating-500w. ), heating element for shaft insulator for esp for 500mw esp. ( for 500mw bhel esp, rating -1.0kw,type- breathing type tubular, 415v. ), heating element for support insulator for esp for 500mw esp., shaft insulator for esp for esp for 500mw esp. ( suitable for 500mw esp,make-m/s. bhel. ), support insulator, type-cylindrical for esp for 500mw esp ( od: 435 + 10 mm; id: 379 + 10 mm; height: 375 + 5 mm,for 500 mw bhel make esp. ), anvil for shock bar assembly #, inner arm for rapping hammer for esp moc-en 8 ( inner arm(ms) for rapping hammer suitable for m/s. bhel make esp ,2x500mw. ), emitting electrode for 500mw esp for esp model faa-9x45m-2x100150-2, hammer assembly,em rapping system # ( outer arm/hammer for eerm of 500 mw bhel make esp ), hammer assembly,col rapping system # ( outer arm/hammer for cerm of 500 mw bhel make esp ), pin insulator for disconnecting switch for esp c.no-71-999, crm horizontal shaft, dia-50mm for esp shaft 1-3 length -4250mmrnshaft 2-3 length -4650mmrnshaft 3-3 length -4790mm ( moc- en8, 400 mm pitch, as per drg. no: 2-79-725-04299 of 500mw bhel unit. section: 02,03 & 04. sleeve tube to be given seperate 04 nos. per set. ), shaft,end,d50xl940mm,en8 w/key&key slot for esp cerm shaft as per bhel drg no: 2-79-725-04299 ( moc: en8 ), shaft,eerm shaft,vertical,dia-40mm for esp 9900mm long,with sleeve,moc-en8 or080m40-bs970 or equivalent ( for 500 mw bhel make esp ), shaft,eerm shaft,horizontal,dia-50mm for esp 9270mm long,with sleeve and set rings,moc-en8 or080m40-bs970 or equivalent ( 03 parts(part-i with key,part-ii & part-iii) with 02 number set ring,02 number sleeve.bhel drawing no.-2-79-716-03812. ), gdrm d-50 shaft moc-en-8 with 19 holes for 500 mw esp serial no-faa-9x45m-2x100150-2 , 3 parts shaft with 19 holes.shaft with sleeve and set rings., big hammer for cerm shaft for 500 mw esp serial no-faa-9x45m-2x100150-2 drg no:2-79-725-04299

CTN :45482035

15 Jun, 2026 19.50 Lacs

Rohtak - Haryana

Tender For supply of various parts of horizontal pumps and tools... - ms flat 50*5 mm, ms angle 50*50*5mm, 50*50*6mm (tata,sail,jindal make), ms channel ismc 100 (tata,sail,jindal make), ss round bar 30 mm(line shaft), ss round bar 40 mm(line shaft), plastic rope 3/4", nut & bolt 5/8"x 3", m.s nut & bolt 5/8" x 21/2", ms nut bolt 5/16x 1.5", ms nut bolt 1/2" x 2", ms nut bolt 1/2" x 11/2", ms nut & bolt 1/2" x 21/2", ms nut & bolt 1/2" x 3", ss nut bolt 3/4x3, stud with nut 11/16 x 5/8 x 3", stud with nut 5/8x 5/8 x 3", gi wire 8 swg, gland packing 3/8", gland packing 1/2", lift belt 5ton cap x 4 mtr, lift belt 3ton cap x 3 mtr, lift belt 3ton cap x 2 mtr, gland plate for n.w-12d, gm gland plate for 5 c/s v.t pump as per sample, g.m gland plate for 10 c/s v.t pump as per sample, pipe wrench 12"(300mm size) (taparia/pye/miranda/spartan/stanley make ), hammer 1lbs, screw driver 10" 250mm (taparia/pye/miranda/spartan/stanley make ), screw driver 12" (taparia/pye/miranda/spartan/stanley make ), screw driver 8" (taparia/pye/miranda/spartan/stanley make ), ring spanner 24x26mm (taparia/pye/miranda/spartan/stanley make ), insulated plier 8" (200mm) (taparia/pye/miranda/spartan/stanley make ), long nose plier 8" (taparia/pye/miranda/spartan/stanley make ), d-e spanner 21x23 (taparia/pye/miranda/spartan/stanley make ), d-e spanner 24x26mm (taparia/pye/miranda/spartan/stanley make ), d-e spanner 14x15mm (taparia/pye/miranda/spartan/stanley make ), d-e spanner 12x13mm (taparia/pye/miranda/spartan/stanley make ), ring spanner 14x15 (taparia/pye/miranda/spartan/stanley make ), ring spanner 21x23 (taparia/pye/miranda/spartan/stanley make ), ring spanner-12x13 (taparia/pye/miranda/spartan/stanley make ), line tester (7"- 8") (taparia/pye/miranda/spartan/stanley make ), freemans 5mx19mm measuring tape with belt clip and lock, hexa blade one side/double side mix, welding holder heavy duty, hdpe tirplaine 15 x12 heavy duty, coupling tyre tc 13, delivery casing for nw-12d inner for kirlosker pump, delivery casing for nw-12d outer for kirlosker pump, impeller 6x6 nw-12d kirloskar pump, bearing pedestal for nw-12d kirlosker make, shaft for nw-12 d pump kirlosker make, lantern ring for nw-12 d pump kirlosker make, water deflector for nw-12 d pump kirlosker make, abrasive cutting wheel 14 (grindwell norton, 3m, bosch make), motor shaft with check nut 5 c/s v.t pump as per sample, impeller nut mf for 5 cs horizontal pump as per sample, fuel pump gear tv-2 kirlosker make, servo super oil mg 20w-40, log book of vehicle (25 page) as per sample, mas register (50 page) as per sample, log book of machinery (25 page) as per sample, cyl liner with joint ring 1800801 kirlosker make, valve kit tv-2 kirlosker make, liner piston chota jawan kirlosker make, head gasket 87.5 mm 1180090300 kirlosker make, air cleaner kirlosker make, packing kit tv-2 kirlosker make, pipe t type kirlosker make, fuel tank complete kirlosker make, fuel filter assy kirlosker make, nozzale chota jawan kirlosker make, air cleaner chota jawan kirlosker make, packing kit chota jawan kirlosker make, valve kit chota jawan kirlosker make, head gasket chota jawan kirlosker make, diesel filter chota jawan kirlosker make, banjo bolt tv2 kirlosker make, nozzle 9430034216 kirlosker make, piston assy.180061000-1800615000 kirlosker make, cr bolt tv2 kirlosker make

Corporations And Associations And Others

CTN :45442968

22 Jun, 2026 NA

Jalandhar - Punjab

Tender For supply of planertary gear box and spares - spares for planetary gearbox make premiumtype p2bh-30, ratio 160/1 ,inputrpm 1000, input bevel pinion, 1st stage bevel gear, 2nd stage pinion, 2nd stage gear, 2nd stage pinion with 1st stage sun, 1st stage ring, 1st stage planet, 2nd stage sun, output ring, output planet, output sun, planetary gear box with motor shaft mounted for open horizontal crystallizer a-massecuitemodel: 5kt-09chm , ratio:- 1454.30input power : 5 hp , input speed : 1440 rpmoutput shaft : hollow (range 96 to 225mm)output speed : 1.00 rpm , rated torque : 60,000nm generated torque :25.070.00nmlubrication :oil , service factor :2.39make: kavitsu transmission/ dynamic oil/flender /magtorque/ premium/max gear note:- depute concern engineer for the same for taking exact dimensions., planetary gear box with motor shaft mounted for irctype p3-20, ratio 160/1 , input rpm 1300make: kavitsu transmission/ dynamic oil/flender/magtorque/ premium/max gear note:- depute concern engineer for the same for taking exact dimensions, reductiongear box make elecon/ radicon/cromptontype u 600ratio 20:1drive both sides

Central Government/Public Sector

CTN :45457375

22 Jun, 2026 5.42 Lacs

Dhanbad - Jharkhand

Tender For (1) complete rewinding/repairing of 120 hp,440 volt,1485 rpm,make simens type-flp,sl.no.64522625 and repairing/machining and motor shaft both side and threading key size making of bearing

Central Government/Public Sector

CTN :45422655

17 Jun, 2026 NA

Jamalpur - Bihar

Tender For supply of set of spares of jamalpur whiting jack capacity 25 ton as per the attached annexure - wj 11/m checknut screw spindle, ball bearing (6215-skf), ball bearing (skf-2310) (top collar bearing), ky-43 key, wj-102 side wheel axle, ky-36 key (right & left link key), ky-63 key for motor shaft, wj-23 sprocket wheel (small), chain duplex roll, wj-29 chain cover (f.r.p), wj-7 top bracket (mod), brake coil (electromagnetic coil) (3.45 kgm, fall safe disc brake, 380/415v, 50 hz, 3 phase), 25 amp starter, n/o-n/c contact (nons contact), ncno contact

Corporations And Associations And Others

CTN :45328794

11 Jun, 2026 19.95 Lacs

Delhi - Delhi

Tender For corrigendum : providing t and p items and garden tools for ward no. 171 (cr park) south zone - providing t & p items and garden tools for ward no. 171 (cr park) south zone., supply of telescopic pole pruner:-specification:-pole length including blade: 6.5mblade material: hardened & tempered high carbon steel. the head of the blade shall have a hooked tip useful for cutting twigssaw blade shape: hooked type curved sawblade type & no of cutting teeth: tripple grounded 86 teeth blade length: 15"-16"pole type: light weight telescopic tubular aluminum alloy extendable poleno of positions for pole heightadjustment: 10 positionslocking mechanism: ergonomicvally designed two way locking mechanismtotal working length: max 219"(6623 mm), mln 103" (3103mm) branch cuttingcapacity: 200mm max, petrol operated brush cutterengine: single cylinder, 2 stroke, aircooled onlyengine displacement: 40.2ccpower output: 2kw/2.7hpmax output shaft speed at cuttingattachment: should be minimum 9000 rpmcarburetor: diaphragm with compensator technology.fuel tank capacity: minimum 600 ml.weight(dry, without cutting attachment & deflector): should not be more than 7.5 kgclutch: centrifugal type, clutch shoe support base & lining metal only.multi function handle: should have acceleration, on/off switch at right handle.brushcutter harness: should be double shoulder harness only.anti vibration system: must have 4- point aniti vibration system.vibration level in m/s2 at right handle: should not be more than 2.5 m/s2sound pressure level db(a): should not be more than 105 db(a)drive shaft design: must have drive shaft ends square design type only.certification: must have valid en certification, telescopic petrol operatedpole prunerengine: single cylinder, 2 stroke, air cooled onlydisplacement: should be between 25-30 ccpower output: should be minimum 1.2 hpweight (dry without cutting attachment & fuel): should not be more than 7.5 kgfuel tank capacity (ml): should be minimum 400mlchain oil capacity (ml): must have minimum 200 ml.clutch: clutch shoe linining should be metal only.guide bar length: minimum 30cmguide bar and chain: should have same manufacture onlychain type: every drive link need groove & small oil holes for better lubrication. saw chain pitch should be 1/4" or 3/8picco only and drive link thickness must have 1.1 mm or 1,3 mm.max. output shaft speed (rpm): should be minimum 8000 rpm at chain sprocket.equipment total length with guide bar and chain (cm): should be minimum 220 cm - compressed & total length of equipment -minimum 350 cm - extended.sound pressure level (db/a): should not be more than 95 db(a)vibration measurement m/s2 at control handle extended position: should not be more than 5.5 m/s2certification: must have tuv certification with test standard en iso 11680, supply of lawn mower:-specification:- type of machine walk behind lawn mowers power sourcepetrol engine engine displacement 224ccstart type recoil / pull startspeed control variable speeddrive type all wheel driveblade style rotary typeblade engagement electromagneticcut width (mm) 525 to 549minimum cut height 20 millimetermaximum cut height 80 millimeterblades hardened steelnumber of blades 1number of positions for cut height adjustment 6number of levers for cut heightadjustment: single levernumber of wheels 4front wheel size 203 millimeterrear wheel size 250 millimeterwheel tyres pneumaticif yes, grass catcher / collector / bag volume 70 liter"engine power rating (watt)" 4000 to 4999engine fuel tank capacity 1.4 ltr., supply of synthetic enamel paint in all shades as per required and direction of officer-in-charge., petrol operated chain sawengine : single cylinder, 2stroke, aircooled onlydisplacement: 45.4cc poweroutput: 2.3kw. 3.0 hpmax. engine speed (with guide bar & chain): at least 12500 rpmcarburetor: diaphragm type compensator technology.fuel tank capacity: should be minimum 450 ml.dry weight(without cutting attachment):should not be mor

Central Government/Public Sector

CTN :45155298

09 Jun, 2026 NA

Solapur - Maharashtra

Tender For corrigendum : repair and amp testing of abb make 770 kw mill motor shaft of ntpc solapur

Central Government/Public Sector

CTN :45002291

05 Jun, 2026 NA

Bhopal - Madhya Pradesh

Tender For bid to ras corrigendum : supply of # 01-tubular shaft assembly complete with fabrication and machining as per annexure-i , # 02- top oil retainer assy complete with fabrication and machining as per annexure-i

Central Government / Public Sector

CTN :45084644

09 Jun, 2026 NA

Begusarai - Bihar

Tender For corrigendum : supply of coupling escodisc dpull 38 make: esco coupling &transmission pvt ltd model: escodisc dpull 38, coupling,model:rem- 65 (140) - i/ ii, rathi, coupling complete set including fastener, coupling complete set including fasteners [rev o2] p/n:xcp501006810030002 model: rem- 25 (140) - iii / iv coupling make:rathi motor: 30 kw / 2950 rpm, coupling,model:rem-65 (255) ii/ii /9797 cplg,rathi tran coupling complete set including fasteners, cplg,discoflex,m165,rathi, cplg,discoflex,m40/180-ii/ii,rath, cplg,discoflex,m40/140-ii/ii,rathi, cplg,discoflex,m65/180-i/ii,rath, unique transmission coupling,, cplg,discoflex,lm10/100,rathi, m-25 suitable for pump shaft d-29.3mm & mtr shft d-48mm, coupling,dbz-c-301,dbse:180, coupling,dbz-c-226,dbse:250, cplg,discoflex,lm/35,rathi, 80 spl 180 dbse size : 180mm, cplg-dbz-c-126/spl/140, coupling, metaflex, comp coupling, dsg power : 1.0-2.0 kw/100 rpm, comp coupling, dsg power : 0.25-0.50 kw/100 rpm, comp coupling, dsg power : 0.50-0.75 kw/100 rpm, comp coupling, dsg power : 8.0-9.0 kw/100 rpm, dbse : 140mm pump shaft dia : 42mm motor shaft dia : 60mm speed : 2955rpm, dbse : 140mm pump shaft dia : 32mm motor shaft dia : 55mm speed : 2960rpm, comp coupling, dsg power : 10.0-11.0 kw/100 rpm

Motor Shaft Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Corporations And Associations And Others

Central Government/Public Sector

Central Government/Public Sector

Corporations And Associations And Others

Central Government/Public Sector

Central Government/Public Sector

Central Government / Public Sector