Tender For requirement of spares of m/s ingersoll rand make conveying air compressor model r-160i-x 7.5wc and up5-22-7 for dry fly ash dense phase system,unit#3 and 4, ctpp, chhabra - model no. r160i-x7.5 wc, seal, shaft high pressure part no. 89292445, element, seprator tank 18 inch part no. 23566938/ 23545841, oil cooler, water cooled part no.23572415, after cooler, water-cooled part no.23572423, cap screw m6x25 soc hd cap w/nylon insert part no.22168710, pressure transducer 0-225 psig part no.47545275001, pressure transducer 0-15 psig part no.47560902001, assembly gear set 160 kw single stage 7.5 bar part no.23521859, pin dowel [motor] part no.39194915, pad pre filter part no.23523772, actuator service kit part no.23467251, inlet valve part no.23421217, elbow 1/4" 90 degree straight thread ms part no.96757604, spacer gear (ce177g) part no.39326483, sleeve motor shaft 4.25 od m132/160 part no.89292478, key,square both ends 0.88sq x1.25 part no.95135638, valve in line check part no.23453020, tube gear case scavenge part no.23453129, air cleaner assembly nlg37-42 pico standard part no.23390156, ultra coolant (208 litres) drum part no.39433743, key, rect one round end part no.96759212, clamp, plate part no.35295336, screw, socket head part no.32555819, housing, seal part no.22880744, gasket, gear case part no.39454558, pin, dowal [air end] part no.35295336, valve, orifice [separator tank] part no.23449200, oil filter assembly part no.23523434, o ring set part no.ok002222, pressure transducer cable part no.23529373, temprature sensor part no.23522246, valve min press check 132-160 kw part no.23521297, 5sv solinied cable part no.23562432, model no. up5-22-7, element coolant filter part no.54672654, element seprator 194cfm (spin-on) part no.54749247, pad pre filter part no.22053722, element air filter part no.89295976, kit, inlet valve repair part no.22067177, kit-mpcv part no.22064695, kit thermal valve repair part no.22393326/ 22832885, valve solenoid 125 inch npt part no.54774302, valve solenoid 1/2 in npt 110 volt part no.54654652, spring gas part no.54749114, elbow .31tx .50sae part no.95993572, elbow , 90deg male 37a10c3xz2 part no.95937686, tube oil feed (rear bearing) part no.85581858, tube, vmc block to bare part no.85581866, belt part no.89265052, ultra coolant (20litres) drum part no.38459582, tempreture sensor part no.22137848, conteroller part no.22128763, tube nylon part no.39124813, tube nylon part no.39124821, elbow part no.39155650, elbow part no.39155577, nipple part no.22354989
Tender For supply of helical inline gear motor to the model no. sk 973.1 - 112mp/4 tf for axle pusher chain conveyor of make m/s nord or substantially equivalent with following features: input speed(rpm): 1440; output speed(rpm): 21; gear ratio: 68.5; power (kw): 4; service factor: 1.8; output torque: 1817 nm; overhung load: 25 kn; axial load: 22 kn; motor inverter speed range: standard line powered inverter capable; voltage: 400/690 v; frequency: 50 hz; efficiency class: ie3; current 1: 7.85 a; current 2: 4.53 a; cosinus: 0.83; motor duty: s1 - continuous; enclosure: ip55; insulation class - f; mounting pos - m1; housing material: cast iron housing; type of housing: foot mount; output shaft: solid keyed shaft; output shaft (dia x length): 60x120mm; output shaft material: standard; gearbox breather options: auto vent; gearbox sealing options:fkm seals; bearing design: standard bearings; motor cooling: tefc - totally enclosed fan cooled; motorthermalprotection: thermistor; motor option: fluoro rubber motor seals; height of output shaft center frombottom of base plate: 225 mm; mounting base plate details: minimum plate thickness: 50 mm; 04 holes of 22 mm dia each with square pattern; distance between holes along the shaft: 310 mm; distance between holes perpendicular to shaft: 250 mm; note: - (i) material of construction: fabricated steel housing (stress relieved) (ii) all gears shall be manufactured from steel forgings or rolled bar made from steel 17cr ni mo6/18cr ni mo6 (case hardening steel). (iii) all gears shall be case hardened to 58-62 hrc and profile ground. (iv) output shaft shall be of en 9 material normalized to 201 bhn (min) (v) bearing used shall be rolling element type of make skf/ntn/timken/fag only. special conditions: above specified materials are the minimum required standard to be considered while designing the gear motor. [ warranty period: 18 months after the date of delivery ] ]
Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - iti palanpur; rewinding of 1 hp single phase water cooler fan motor; service provider,repair, maintenance, and installation of plant/ systems/equipments (version 2) - iti palanpur; rewinding of 2 hp single-phase motor of grass cutter machine; service provider
Tender For providing of repair, maintenance, and installation of plant/ systems/equipments (version 2) - tent cooler motor rewinding with coper wire bearing of motor to be replaced where necessary rear side iron net installation of motor and fitting of attachments screws for fixing of nets/motors and other accessary
Tender For repair maintenance of comprehensive maintenance through outsourcing of various electrical and mechanical services installed at gtb hospital, shahdara, delhi. - rmo comprehensive maintenance through outsourcing of various e&m services installed at gtb hospital, shahdara, delhi. (sh:- sitc of window ac unit and desert cooler motor at various location in gtb, hospital complex, shahdara, delhi).
Tender For supply of voltas 320 ltrs deep freezer repair , 1 and half ton window ac repair lg , 100 ltr water ro repair and servicing , 1 and half ton videocon ac repair , purchase of cooler grass small , purchase of cooler grass medium , purchase of cooler grass large , replacement of cooler fan motor , replacement of cooler fan , replacement of cooler water pump , replacement of cooler water pump pipe , replacement of cooler switch plate , replacement of cooler water pump large , replacement of cooler capacitor , cooler wiring repair , bicycle repair , diesel generator set 15 kw three phase engine
Tender For supply of replacement of vinyl flex printed size 16 feet x 5 feet , repair of wall fan and replacement of condenser , repair of desert cooler motor , repair of commercial ro incl servicing and replacement of filter , repair of ac motor copper rewinding , repair of ac consenser coil , repair of ac service charges , office table glass