Latest ms motor Tenders | Government ms motor Tenders

Central Government/Public Sector

CTN :45296198

12 Jun, 2026 1.60 Lacs

Barmer - Rajasthan

Tender For supply of filter opening wrench mahindra bolero , mahindra bolero differential drain opening socket , electric cordless impect wrench opening machine with socket set heavy duty , small socket set , fuel pipe lock opening plier , heavy vehicle hydraulic jack ten ton , filter opening wrench ashok leyland , puller for removing gear , clutch hub check nut puller for motor cycle , tappet adjuster for motor cycle , magenet puller for motor cycle , oil filter removing tool chain type , puller small for bearing remove , screw driver plus and minus two in one twelve inch , hydrometer , digital multimeter , soldering iron , nose plier , elak battery tester for testing , combination player eight inch , gas regulator for oxygen isi mark , gas regulator for da isi mark , bosch hammer drill gsb10re , welding holder , drill bit set , measurement tape 05 mtr , welding cable 25 meter , cutting plier , impact goti set , ball pin hammer 800 gm and 500 gm , white goggles , angle cutter machine bosch , bench grinder wheel fine , bench grinder wheel ruff , writing brush zero to twelve no , painting brush two inch , scale steel rule 2.5 feet , buffer machine , painting mask , spray gun for painting , air liner pipe , heavy duty tyre lever big size , hammer three kg , tyre buffing machine , hot puncture machine , liquid tyre pressure gauge , file for buffing , chisel sixteen inch for tyre puncture , hacksaw frame taparia , chisel for carpentary , scissor , motor for sewing machine ) /bid number : gem/2026/b/7575969 * /dated: 22-05-2026 & & / bid document 1 / 39

Central Government And Public Sector

CTN :45279869

04 Jun, 2026 2.90 Lacs

Ahmedabad - Gujarat

Tender For supply of service 11 kv ht panel as per sepcifications , sf new mineral oil for panel etc as per sepcifications , calibration relay etc as per sepcifications , replacement digital ammeter for ht panel , replacement digital voltmeter for ht panel , replacment ryb ind lamp led type in ht panel , sf 2a hrc fuselink in ht panel , servicing 1500kva dry type transformer as per sepcifications , servicing 2 runs 2500a tpn bustrunking as per sepcifications , service mv lt panel with 2500a 4p acb 3 nos as per specifications , service mvlt panel with mccb incoming as per specifications , checking and repair of em intelocking , dismentaling 3.5 sq mm 240 or 300 sq mm al cable as required , pf adaptor box aprx 1.5 ft x 1.5 ft x 1.5ft of 16swg ms sheet as reqd , pvdg panel module door key as reqd , pvd and fixing operating handle for 250a 4p changeover as reqd , replacement 160a hrc fuse with base in extg cap panel , replacement 3p 50kvar cap duty contactor in extg cap panel , replacement 25sq mm cu lead wire 1ft length in extg cap panel , checking etxg 2no 25kvar cap bank and fault repair reinstallation , dismentaling uv protection connections as reqd , replacement digital ammeter for lt panel , replacement digital voltmeter for lt panel , replacment selector switch in lt panel , replacment ryb ind lamp led type in lt panel , sf 2a hrc fuselink in lt panel , sf 32a hrc fuseling incl removing faulty item from lt panel as reqd , sf 63a hrc fuseling incl removing faulty item from lt panel as reqd , sf 100a or125a hrc fuseling incl removing faulty item from lt panel as reqd , sf 250a hrc fuseling incl removing faulty item from lt panel as reqd , sf new 5 or 6 amp piano switch in replacement of faulty item , sf new 5 or 6 amp 3pin socket outlet in replacement of faulty item , sf new 15 or 16 amp piano switch in replacement of faulty item , sf new 15 or 16 amp 6pin socket outlet in replacement of faulty item , rewinding ceiling fan motor , sf 4ft 20w led fitting against faulty fitting , service of 750kva dg set as per specification , service dgset control panel 1250a 4p acb as per specification , repacement ryb ind lamp in dg set panel , repacement digital ammeter in dg set panel , earthing testing in existing earth pits and report submission

CTN :45294044

10 Jun, 2026 5.25 Lacs

Midnapore - West Bengal

Tender For supply, installation, testing and commissioning of 75 hp submersible pump motor set

CTN :45057581

27 May, 2026 9.50 Lacs

Farrukhabad - Uttar Pradesh

Tender For corrigendum : supply of fabrication and erection work e e - places , replacing wornout runner base and installing a new runner base of cane carrier and baggage elevator and r b c , replacing wornout runner with new one of cane carrier and baggage elevator and r b c , removing wornout angle iron and t iron of the cane carrier and reinstalling it by straightening the crooked part , removing the wornout part of the suit from different places and fitting it with new one , chevron grooving of new rollers of the mill , chevron grooving of old rollers of the mill , remove the wornout partition plates of the juice box above and below the juice heater by 10 or 12 mm ms plate and install it , installing ribs at the top and bottom partitions of the juice heater , repairing save all of qurdbody , removing old wornout gutters installed at various places and installing it with new gutters , remove the old wornout save all from pan and quard and install it with new one , reinstalling the new umbrella fitted inside the pan by making a new one and removing the old one , replacement ribbon arm of the mascute receiving crystallizer , making new separator of a centrifugal machine , removing the wornout truff of the hopper and installing it with new one , making and installing new separators for continuous centrifugal machines , removing the tubes of quad juice heater and dynamic juice heater and expanding them by installing new tubes and giving their hydraulic testing satisfactory of size 42 mm , removing the tubes of pan installing new tubes and expanding them and giving hydraulic tesing with satisfactory trial of size 96 mm , removing the wornout flue gas ducting of both the boilers and installing it with newone making from new or old plates , removing the wornout front and roof plate at boiler number 1 and 2 and installing with a new plate , removing the damaged boiler damper and installing a new one , making bagasse suit and installing. , replacement of juice over flow box of clarifier , making and installing bed of motor and pumps at various places as per requirement , replacement 6 inch dia cooling pipe of sulfur furnace , removing the monitor casing of a machine from old machine and installing it and giving its a trial , making amd replacing manholes at various places , making and replacing the enternals of cather of the pan. , making and replacing the new hood of cane cutter , removing the old bottom plate of the lowest compartment of the clarifier and placing a new plate on it after placing an angle trap as per the instructions and giving a satisfactory water trial , reinstalling the stirrer of the clarifier and giving a satisfactory trial , removing the shaft of a pug mill and replacing the old bushes on both sides and fitting new ones , removing and refitting the shaft of a brown sugar magma mixer and installing with new bush , reinstalling the trufff of connecting rod of the hopper , making and installing new catcher strainer , removing the old rail line of the trolley of the unloader and fitting the new rail line satisfactorily and doing water level , reinstalling the old rail line of the unloader s bridge and fitting it and checking water level etc , removal of old and weak channels of 3 inches to 10 inches diameter installed at various places and installation of new ones as per requirement , cutting and straightening old plates installed at various places as per requirement , removal of old and wornout scrubber installed on sulfur furnace and making and replacing with 8 or 10 mm plate and making all the connections , removing the trufff plate including support corroded shell and top cover plate of the top chamber of the clarifier and fitting the new plate and giving it s a water proof trial , re-installation alignment and //bid details 2 / 47 trial of hopper driving end , making and installing the top cover of the centrifugal machine , making an arm and installing it on the shaft of pug mill , making and installing scrubber and bot

CTN :44989585

25 May, 2026 NA

Mumbai - Maharashtra

Tender For corrigendum : supply and installation of training items for drone technician trade under craftsman training scheme (cts) at consignee locations - pliers, soldering station, multi meter, binoculars, anemometer, magnifier, unassembled drone kit, unassembled drone kit - standard with hd camera & thermal camera, electricity lab, smd technology kit with wall chart, dc regulated variable programmable dc power supply, drone workbench, analog-digital circuits development platform, applied mechanics training platform, drone battery management training systems, charge controller training system, bldc (brushless dc) motor training system, inverted pendulum, drone sensor trainer kit, antenna training system, advanced microwave integrated circuit lab, gps training platform, wireless communication modules, fcb and esc training platform, drone gimbal set with motor and control, npnt compliant micro uav built for mapping and surveillance, field repair kits, drones and spare parts kit, balance charger, power distribution board, laptop latest configuration, thrust measurement meter, indoor netted facility, outdoor controlled netted testing facility, various electronic and electrical components, 3d printer, drone ( long range)

CTN :45254893

27 May, 2026 NA

Jamshedpur - Jharkhand

Tender For supply & testing of high vacuum type transformer oil filtration machine of capacity: 1000 lph for 415v, ac, 3 phase operation, operating temperature range 40' c - 70' c and conform to is: 60341989 (reaffirmed 2005), compact type with dimension not more than length: 2.0 mtr. and breadth: 1.0 mtr. including suitable size of trolley and wheel with all accessories. the machine shall include suction pump with flow rate 1 hp 20 lpm, motor capacity (cg/havells/siemens/kirloskar make), vacuum pump motor capacity 0.75 hp (cg/havells/siemens/kirloskar make), magnetic strainer, degassing chamber capacity 95 itr or higher, suitable size dirt bag. the cost is inclusive of complete set with powder coating painted control panels, protection devices, flow meter to monitor volume of oil filtered, temperature gauge, safety relief valve, inlet & outlet pipe each of 10 mtr. length and all accessories necessary for transformer oil filtration operation. the machine shall be capable for removal of moisture, gas and solid particles and achieve breakdown voltage(dielectric) 270 kv post filtration. after supply, contractor shall arrange demonstration, training on operation, maintenance and troubleshooting in presence of concerned ssee(g) & staff/operator. make: cbs technologies/ sbe or reputed make conforming to is as approved by dee(g)/ckp before supply, gad of filtration plant set with details of all parts including trolley, wheel etc. shall be submitted to dee(g)/ckp for approval. [warranty period: 30 months after the date of delivery ] ]

CTN :45214159

27 May, 2026 NA

Tonk - Rajasthan

Tender For corrigendum : supply of design engineering inspection testing supply of flp motor driven hydraulic variable suction cng booster compressor with canopy having avg flow capacity of 400 scmh , lcv unloading post with coriolis mass flow meter 4 inch dial size pressure gauge , installation and commissioning at site along with field performance acceptance test , operation charges for 1st year i e during warranty period , comprehenesive maintenance charges for 1st year after completion of warranty period , comprehensive maintenance charges for 2nd year i e after completion of 1st year post warranty , comprehensive maintenance charges for 3rd year i e after the completion of 2nd year post warranty , comprehensive maintenance charges for 4th year i e after the completion of 3rd year post warranty

CTN :43369597

23 May, 2026 NA

Nagpur - Maharashtra

Tender For bid to ras corrigendum : providing of custom bid for services - one time repairing replacement of both sides bearing of siemens make spindle motor type no 1ph 8165 1df00 1ca1 including motor servicing and testing

CTN :45264542

25 May, 2026 NA

Malda - West Bengal

Tender For 1) supply of condenser motor suitable for water cooler of different capacity as per site requirement - 20 nos (2) supply of thermostat switch suitable for water cooler of different capacity as per site requirement - 42 nos (3) supply of starting relay & overload starting capacity complete set suitable for water cooler of different capacity as per site requirement -25 nos (4) supply of r-22 gas brezzing oiling leak testing complete fitting suitable for water cooler of different capacity as per site requirement -23 set (5) supply of following materials (i) fan blade suitable as per site requirement ? 25 set. (ii) water drain pipe of suitablelength. (iii) pvc water tap (1/2?_ -25 nos. for water cooler of different capacity as per site requirement -01 job. [ warranty period: 30 months after the date of delivery ] ]

corporations/Associations/Others

CTN :45275625

03 Jun, 2026 3.70 Lacs

Kolkata - West Bengal

Tender For repairing, overhauling and heat varnishing of stator and rotor with necessary testing and commissioning of 580 bhp h.t. motor unit no. 2 at mullick ghat pumping station

Ms Motor Tenders

By Cities

By States

By Agencies

By Ownerships

By Sectors

Central Government/Public Sector

Central Government And Public Sector

corporations/Associations/Others